<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[How To Tell?]]></title><description><![CDATA[<p dir="auto">Is there a way to tell whether the scales on a SAK are hollow or solid, other than removing them? I want to make a small hole for the straight pin, but it seems I can only do this on the hollow scales and I don't want to pry off every set of scales I own if it's not necessary.</p>
<p dir="auto">Also, if I want to cut a slot for the pen, will the stock scales work, or are they too thin? I think the Plus scales area little thicker to allow the pen to slide in and out.</p>
]]></description><link>https://multitool.ninja/topic/39974/how-to-tell</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 02:12:41 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/39974.rss" rel="self" type="application/rss+xml"/><pubDate>Thu, 20 Sep 2012 00:12:11 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to How To Tell? on Thu, 20 Sep 2012 14:17:46 GMT]]></title><description><![CDATA[<ol start="24">
<li>The Officer can write<br />
Any of the Officer models that has a toothpick or tweezer can have<br />
an SAK pen instead of the T or T: Remove the T (or T). Hold the knife between<br />
the jaws of a vise, padded with cardboard, so the plastic scale will<br />
not bulge away from the liner when the bit goes in. Send a twirling drill bit<br />
down the T or T hole, keeping the bit against the liner. All Vic pens, long<br />
(91mm knives) and short (58 mm Signature I and II), are .09” or 2.2mm<br />
wide; a 3/32 (or a #41 = .096”) bit works. If you are installing a long pen<br />
the bit will be too short and you will have to remove the scale and finish<br />
the groove with a knife or other tool; snap or glue the scale back on (see<br />
Repair 11).<br />
The SAK Owner's Manual</li>
</ol>
]]></description><link>https://multitool.ninja/post/640533</link><guid isPermaLink="true">https://multitool.ninja/post/640533</guid><dc:creator><![CDATA[J Mackrel Jones]]></dc:creator><pubDate>Thu, 20 Sep 2012 14:17:46 GMT</pubDate></item><item><title><![CDATA[Reply to How To Tell? on Thu, 20 Sep 2012 07:32:10 GMT]]></title><description><![CDATA[<p dir="auto">Are plus scales really solid these days?</p>
<p dir="auto">I've got a few unused ones at home that I got from Tom earlier this year.. could've sworn they weren't solid.. but I haven't looked at them for quite some time now however.</p>
]]></description><link>https://multitool.ninja/post/640458</link><guid isPermaLink="true">https://multitool.ninja/post/640458</guid><dc:creator><![CDATA[Northern Geek]]></dc:creator><pubDate>Thu, 20 Sep 2012 07:32:10 GMT</pubDate></item><item><title><![CDATA[Reply to How To Tell? on Thu, 20 Sep 2012 06:41:21 GMT]]></title><description><![CDATA[<p dir="auto">i dug out some scales to compare. The Plus scales seem to be thicker bay the same amount of Cellidor which is covering the Pen´s slot, so basically this slot is as deep as a standard scale. I would doubt taht you can fit it into a standard scale.</p>
<p dir="auto">Solid scales will accept the pin, the plus scales are solid (except for the slots), yet have the pin slot.<br />
Older hollow scales do not have enough material on the inside to hold a pin.<br />
I do not know a way to tell hollow from solid scales. sorry.</p>
]]></description><link>https://multitool.ninja/post/640448</link><guid isPermaLink="true">https://multitool.ninja/post/640448</guid><dc:creator><![CDATA[lowtech]]></dc:creator><pubDate>Thu, 20 Sep 2012 06:41:21 GMT</pubDate></item></channel></rss>