<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Schrade ST1 variations]]></title><description><![CDATA[<p dir="auto">The ST1 Tough Tool was produced in the USA from 1997 until Schrade shut down in 2004. There are a suprising number of variations in the tools considering the short time they were in production. We recently talked about it in this thread <a href="/topic/3765">HERE</a>. After buying and borrowing a number of different Tough Tools I've managed to identify these four variations here:</p>
<p dir="auto"><strong>JAWS:</strong><br />
The original Series 1 tools had jaws produced by stamping six different pieces out from heavy gauge sheet metal then laminating them together with rivets. Fine and coarse serrations were then cut into this sandwich of jaw plates, no doubt an expensive operation. Wire cutter area was also cut after stamping. Note stylized SCHRADE logo and right-side-up USA logo.</p>
<p dir="auto"><img src="https://wiki.multitool.org/show_image.php?id=838" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Series 2 tools appeared sometime before 2000 (based on a photograph in the 2000 Field &amp; Stream ad) Jaws were still produced from six pieces riveted together, but the pieces had changed somewhat. Now the center sections were investment cast, while only the outer four plates were stamped steel. Serrations were still cut after assembly. Wire cutters however were cast in from the start, eliminating some cost. Note plain SCHRADE logo and upsidedown USA logo.</p>
<p dir="auto"><img src="https://wiki.multitool.org/show_image.php?id=840" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">The entire jaw was cast solid on the Series 3 tools. Somewhat humorously, fake rivet heads were also cast into the jaws. (even though they serve no function) Jaw serrations were also cast in instead of cut in afterwards. By eliminating the rivets and the "sandwich" construction, number of pieces for a complete plier head was reduced from ten down to only two. Plus no more labor involved in assembly, riveting, and cutting serrations. Cost savings must have been considerable.</p>
<p dir="auto"><img src="https://wiki.multitool.org/show_image.php?id=841" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">After Taylor Brands acquired the Schrade name, production of the ST1 was resumed in China. These Series 4 Tough Tools resemble the American made models in appearance only. Close examination makes it clear that none of the dies or tooling from the original plant is being used to manufacture today's tools. Jaws remain entirely cast, with heavy burrs on a number of inner surfaces. The SCHRADE logo is now cast in place. Also note the flush plier pivot.</p>
<p dir="auto"><img src="https://wiki.multitool.org/show_image.php?id=839" alt="" class="img-markdown  img-fluid" /></p>
]]></description><link>https://multitool.ninja/topic/4767/schrade-st1-variations</link><generator>RSS for Node</generator><lastBuildDate>Mon, 16 Nov 2026 00:40:48 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/4767.rss" rel="self" type="application/rss+xml"/><pubDate>Sun, 11 May 2008 01:15:17 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Schrade ST1 variations on Mon, 12 May 2008 17:16:15 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/j-sews" aria-label="Profile: J-sews">@<bdi>J-sews</bdi></a> <a href="/post/78543">said</a>:</p>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/leatherman123" aria-label="Profile: Leatherman123">@<bdi>Leatherman123</bdi></a> <a href="/post/78531">said</a>:</p>
<blockquote>
<p dir="auto">It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though!  ???</p>
</blockquote>
<p dir="auto">They don't <em>look</em> that bad, but trust me, they are. I'm embarrassed to admit that I paid $14 for this one.  :-[</p>
</blockquote>
<p dir="auto">At least you've SAVED a few of us $14 mate <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f642.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--slightly_smiling_face" style="height:1.4em;width:auto;vertical-align:middle" title=":)" alt="🙂" /></p>
]]></description><link>https://multitool.ninja/post/78665</link><guid isPermaLink="true">https://multitool.ninja/post/78665</guid><dc:creator><![CDATA[Mike, Lord of the Spammers!]]></dc:creator><pubDate>Mon, 12 May 2008 17:16:15 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Mon, 12 May 2008 14:53:53 GMT]]></title><description><![CDATA[<p dir="auto">If anybody is interested if have one T1 Tough Tool series 3 for trade, is used but not abused.<br />
I'm looking for a Black Oxide CORE or SWISSTOOL.<br />
PM me or drop me a line to <a href="mailto:jfcm44@hotmail.com" rel="nofollow ugc">jfcm44@hotmail.com</a></p>
<p dir="auto">Thanks.</p>
]]></description><link>https://multitool.ninja/post/78636</link><guid isPermaLink="true">https://multitool.ninja/post/78636</guid><dc:creator><![CDATA[tango44]]></dc:creator><pubDate>Mon, 12 May 2008 14:53:53 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 22:46:52 GMT]]></title><description><![CDATA[<p dir="auto">It looks like mine is a second generation model:</p>
<p dir="auto"><a href="http://www.multitool.org/miscellaneous-tools/large-tools/schrade-st1.html" rel="nofollow ugc">http://www.multitool.org/miscellaneous-tools/large-tools/schrade-st1.html</a></p>
<p dir="auto">I'll have a closer look and let you know if there are any other variations on mine, but mine has seen better days so if they are subtle, they may not be visible.</p>
<p dir="auto">Def</p>
]]></description><link>https://multitool.ninja/post/78573</link><guid isPermaLink="true">https://multitool.ninja/post/78573</guid><dc:creator><![CDATA[Grant Lamontagne]]></dc:creator><pubDate>Sun, 11 May 2008 22:46:52 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 19:31:28 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto">@Defender <a href="/post/78500">said</a>:<br />
........it's obvious quality went downhill after Schrade went out of business, but how is the Gen 3 quality overall?  Do you think the difference between cast heads and laminated heads changes the quality any?  The change makes sense <em>if</em> there's no appreciable loss of quality/strength but it's cheaper to manufacture.</p>
<p dir="auto">Def</p>
</blockquote>
<p dir="auto">Oops, guess I should clarify. In my opinion, the overall quality of Series 1 thru 3 made in USA tools are all quite good. Changing from labor-intensive laminated plier jaws to investment cast ones did not take away anything from the tool. If anything it made the ST1 more comparable to multitools from Leatherman and Gerber and everyone else who ALWAYS used cast plier heads.</p>
<blockquote>
<p dir="auto">@Defender <a href="/post/78500">said</a>:<br />
......Have you identified any other generational differences between the various incarnations?.....</p>
</blockquote>
<p dir="auto">As a matter of fact there is an entire Encyclopedia page devoted to just that topic: <a href="https://wiki.multitool.org/tiki-index.php?page=ST1+Tough+Tool+variations" rel="nofollow ugc">https://wiki.multitool.org/tiki-index.php?page=ST1+Tough+Tool+variations</a></p>
<p dir="auto">Does anyone have an ST1 model with features other than what is listed?</p>
]]></description><link>https://multitool.ninja/post/78545</link><guid isPermaLink="true">https://multitool.ninja/post/78545</guid><dc:creator><![CDATA[J-sews]]></dc:creator><pubDate>Sun, 11 May 2008 19:31:28 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 19:22:04 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/leatherman123" aria-label="Profile: Leatherman123">@<bdi>Leatherman123</bdi></a> <a href="/post/78531">said</a>:<br />
It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though!  ???</p>
</blockquote>
<p dir="auto">They don't <em>look</em> that bad, but trust me, they are. I'm embarrassed to admit that I paid $14 for this one.  :-[</p>
]]></description><link>https://multitool.ninja/post/78543</link><guid isPermaLink="true">https://multitool.ninja/post/78543</guid><dc:creator><![CDATA[J-sews]]></dc:creator><pubDate>Sun, 11 May 2008 19:22:04 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 16:58:27 GMT]]></title><description><![CDATA[<p dir="auto">It really is a POS! Bob, how much did you pay for it?/! I saw a Chinese made one at Kmart yesterday.. It didn't look AS bad as yours though!  ???</p>
]]></description><link>https://multitool.ninja/post/78531</link><guid isPermaLink="true">https://multitool.ninja/post/78531</guid><dc:creator><![CDATA[Leatherman123]]></dc:creator><pubDate>Sun, 11 May 2008 16:58:27 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 16:23:51 GMT]]></title><description><![CDATA[<p dir="auto">Thanks for that Bob, it was very interesting.  <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f642.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--slightly_smiling_face" style="height:1.4em;width:auto;vertical-align:middle" title=":)" alt="🙂" /></p>
<p dir="auto">That chinese one is shockingly awful isn't it.  <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f615.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--confused" style="height:1.4em;width:auto;vertical-align:middle" title=":-\" alt="😕" /></p>
]]></description><link>https://multitool.ninja/post/78520</link><guid isPermaLink="true">https://multitool.ninja/post/78520</guid><dc:creator><![CDATA[Benner]]></dc:creator><pubDate>Sun, 11 May 2008 16:23:51 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 16:10:06 GMT]]></title><description><![CDATA[<p dir="auto">That really is awful <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f620.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--angry" style="height:1.4em;width:auto;vertical-align:middle" title="&amp;gt;:(" alt="😠" /></p>
]]></description><link>https://multitool.ninja/post/78517</link><guid isPermaLink="true">https://multitool.ninja/post/78517</guid><dc:creator><![CDATA[Mike, Lord of the Spammers!]]></dc:creator><pubDate>Sun, 11 May 2008 16:10:06 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 13:51:54 GMT]]></title><description><![CDATA[<p dir="auto">Wow- it actually hurts to look at that!</p>
<p dir="auto">Have you identified any other generational differences between the various incarnations?  It might be interesting to see the other goodies- it's obvious quality went downhill after Schrade went out of business, but how is the Gen 3 quality overall?  Do you think the difference between cast heads and laminated heads changes the quality any?  The change makes sense <em>if</em> there's no appreciable loss of quality/strength but it's cheaper to manufacture.</p>
<p dir="auto">Def</p>
]]></description><link>https://multitool.ninja/post/78500</link><guid isPermaLink="true">https://multitool.ninja/post/78500</guid><dc:creator><![CDATA[Grant Lamontagne]]></dc:creator><pubDate>Sun, 11 May 2008 13:51:54 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 11:44:33 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/spoonrobot" aria-label="Profile: Spoonrobot">@<bdi>Spoonrobot</bdi></a> <a href="/post/78438">said</a>:<br />
Excellent!</p>
<p dir="auto">Thanks for taking the time and energy to put this together. I have a series 2 but will be on the lookout for other ones now that we have some more information on the subject.</p>
<p dir="auto">You washed your hands after handling the series 4, right?  <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f61b.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--stuck_out_tongue" style="height:1.4em;width:auto;vertical-align:middle" title=":P" alt="😛" /></p>
</blockquote>
<p dir="auto">Washed AND disinfected!  <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f61b.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--stuck_out_tongue" style="height:1.4em;width:auto;vertical-align:middle" title=":P" alt="😛" /></p>
<p dir="auto">This Chinese version is sooooo bad. The sheet metal on the left handle is warped and distorted. Two of the knife blades don't fold into it properly. Chinese solution? Simply bend the tips of the blades over until they do fit. ::)</p>
<p dir="auto"><img src="http://img.photobucket.com/albums/v307/jooliesews/Bobbys/chineseschrade.jpg" alt="" class="img-markdown  img-fluid" /></p>
]]></description><link>https://multitool.ninja/post/78474</link><guid isPermaLink="true">https://multitool.ninja/post/78474</guid><dc:creator><![CDATA[J-sews]]></dc:creator><pubDate>Sun, 11 May 2008 11:44:33 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 05:41:13 GMT]]></title><description><![CDATA[<p dir="auto">Excellent!</p>
<p dir="auto">Thanks for taking the time and energy to put this together. I have a series 2 but will be on the lookout for other ones now that we have some more information on the subject.</p>
<p dir="auto">You washed your hands after handling the series 4, right?  <img src="https://multitool.ninja/assets/plugins/nodebb-plugin-emoji/emoji/android/1f61b.png?v=b41cf6e2207" class="not-responsive emoji emoji-android emoji--stuck_out_tongue" style="height:1.4em;width:auto;vertical-align:middle" title=":P" alt="😛" /></p>
]]></description><link>https://multitool.ninja/post/78438</link><guid isPermaLink="true">https://multitool.ninja/post/78438</guid><dc:creator><![CDATA[Spoonrobot]]></dc:creator><pubDate>Sun, 11 May 2008 05:41:13 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 04:14:37 GMT]]></title><description><![CDATA[<p dir="auto">If it don't say USA,stay away!!!</p>
]]></description><link>https://multitool.ninja/post/78434</link><guid isPermaLink="true">https://multitool.ninja/post/78434</guid><dc:creator><![CDATA[Smitty44]]></dc:creator><pubDate>Sun, 11 May 2008 04:14:37 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 02:30:03 GMT]]></title><description><![CDATA[<p dir="auto">Yeah nice pics Bob the first 2 pics were definately best quality, while the l;ast you can visibly see is of much less quality. Sad to see such a nice tool degrade like that.</p>
]]></description><link>https://multitool.ninja/post/78418</link><guid isPermaLink="true">https://multitool.ninja/post/78418</guid><dc:creator><![CDATA[Poncho65]]></dc:creator><pubDate>Sun, 11 May 2008 02:30:03 GMT</pubDate></item><item><title><![CDATA[Reply to Schrade ST1 variations on Sun, 11 May 2008 02:25:19 GMT]]></title><description><![CDATA[<p dir="auto">Thanks a lot Bob, I always wondered about the variations! It's amazing how companies can go down hill to save a buck!</p>
]]></description><link>https://multitool.ninja/post/78417</link><guid isPermaLink="true">https://multitool.ninja/post/78417</guid><dc:creator><![CDATA[Leatherman123]]></dc:creator><pubDate>Sun, 11 May 2008 02:25:19 GMT</pubDate></item></channel></rss>