<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[SAK Assembler]]></title><description><![CDATA[<p dir="auto">I originally put SAKs together "freehand" trying to get the layers to stay together while compressing springs and juggling tools.   If you've ever tried it, you'll know how frustrating it can be.</p>
<p dir="auto">I made this jig to hold the pins steady as layers are added and wanted to share it here.   The jig takes minutes to make and will simplify things a lot.</p>
<p dir="auto">Start with a piece of corian, sturdy wood, thick plastic, micarta or whatever you can find.    Figure out the pin sizes you need for the mod and find drill bits just a hair larger than the pin diameter (I mean it!  1 or 2 thousanths over the diameter of the pin for best results)</p>
<p dir="auto">A decent set of fractional drill bits can be found at <a href="http://knifekits.com" rel="nofollow ugc">knifekits.com</a> that has all the sizes you need and lots more for around $35</p>
<p dir="auto">Use one of the liners fro the SAK you're modding as a template for drilling the hole patterns into your SAK platform.</p>
<p dir="auto">Set the liner close enough to the edge so when you are assembling, you can use the edge of the platform as a pry point for your pliers for compressing the springs.</p>
<p dir="auto">Check out the pictures below and it should make sense.</p>
<p dir="auto">The tighter holes you drill and the deeper the hole you use, the stronger the system will be and the easier it will be to put the knives together.</p>
<p dir="auto">Here are some pin sizes and the drill bits I use that work well</p>
<p dir="auto">84mm SAK - uses 0.085in pins (2.25mm)  - Drill holes that are .086-.088in about 7-10mm deep.</p>
<p dir="auto">91mm SAK - uses .085in pins for the inside pins and .098in (2.5mm) for the outside pins.    Drill holes that are .086-.088in and .099-0.100in 10mm deep</p>
<p dir="auto">You will waste some brass pinstock by drilling the holes deeper, but its cheap and the other alternative is to drive yourself nuts until you start breaking things which is quite a bit more costly!</p>
<p dir="auto"><img src="http://i9.photobucket.com/albums/a75/scibeer/SAKassembler001.jpg" alt="" class="img-markdown  img-fluid" /><br />
<img src="http://i9.photobucket.com/albums/a75/scibeer/SAKassembler005.jpg" alt="" class="img-markdown  img-fluid" /><br />
<img src="http://i9.photobucket.com/albums/a75/scibeer/post100k.jpg" alt="" class="img-markdown  img-fluid" /></p>
]]></description><link>https://multitool.ninja/topic/5063/sak-assembler</link><generator>RSS for Node</generator><lastBuildDate>Tue, 17 Nov 2026 02:16:43 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/5063.rss" rel="self" type="application/rss+xml"/><pubDate>Sun, 01 Jun 2008 03:51:44 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to SAK Assembler on Fri, 28 May 2010 15:10:39 GMT]]></title><description><![CDATA[<p dir="auto">Yes.  That's exactly what I wanted to know. :)</p>
]]></description><link>https://multitool.ninja/post/379780</link><guid isPermaLink="true">https://multitool.ninja/post/379780</guid><dc:creator><![CDATA[porteiro]]></dc:creator><pubDate>Fri, 28 May 2010 15:10:39 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Fri, 28 May 2010 14:49:34 GMT]]></title><description><![CDATA[<p dir="auto">The pins I assemble the knife on in the jig are the pins I peen.   I don't flatten out one side first.   Both sides are normal pinstock when I'm done assembling.   I pull the knife off the jig (carefully!) and peen each side after trimming and grinding the pins to the correct length with pliers and a dremel or belt sander.</p>
<p dir="auto">Rest one side of the pins on a piece of metal or little anvil of some kind to peen against.   Does that help?</p>
]]></description><link>https://multitool.ninja/post/379773</link><guid isPermaLink="true">https://multitool.ninja/post/379773</guid><dc:creator><![CDATA[scibeer]]></dc:creator><pubDate>Fri, 28 May 2010 14:49:34 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Thu, 27 May 2010 05:00:45 GMT]]></title><description><![CDATA[<p dir="auto">I know this is an old thread, but...</p>
<p dir="auto">Once you have the knife assembled on the jig, how do you then transfer it to the pins that have one end peened over?</p>
<p dir="auto">Or do you peen over the pins in place in the jig?</p>
]]></description><link>https://multitool.ninja/post/379255</link><guid isPermaLink="true">https://multitool.ninja/post/379255</guid><dc:creator><![CDATA[porteiro]]></dc:creator><pubDate>Thu, 27 May 2010 05:00:45 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Thu, 05 Jun 2008 03:21:37 GMT]]></title><description><![CDATA[<p dir="auto">I'm glad it was useful to someone.</p>
<p dir="auto">I bled plenty for the both of us my friend!</p>
]]></description><link>https://multitool.ninja/post/85582</link><guid isPermaLink="true">https://multitool.ninja/post/85582</guid><dc:creator><![CDATA[scibeer]]></dc:creator><pubDate>Thu, 05 Jun 2008 03:21:37 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Tue, 03 Jun 2008 11:20:20 GMT]]></title><description><![CDATA[<p dir="auto">Cheers Bill.  Thanks to seeing your jig over on SOSAK I never had to go through the frustration of using clips and clamps for my first mods.  The first thing I did was make a jig.</p>
<p dir="auto">So thank you for the hours and blood saved <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /></p>
<p dir="auto">Neil</p>
]]></description><link>https://multitool.ninja/post/85058</link><guid isPermaLink="true">https://multitool.ninja/post/85058</guid><dc:creator><![CDATA[Neil]]></dc:creator><pubDate>Tue, 03 Jun 2008 11:20:20 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Sun, 01 Jun 2008 20:41:19 GMT]]></title><description><![CDATA[<p dir="auto">Thanks Bill!</p>
]]></description><link>https://multitool.ninja/post/84615</link><guid isPermaLink="true">https://multitool.ninja/post/84615</guid><dc:creator><![CDATA[Leatherman123]]></dc:creator><pubDate>Sun, 01 Jun 2008 20:41:19 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Sun, 01 Jun 2008 13:43:20 GMT]]></title><description><![CDATA[<p dir="auto">Very generous of you to share that Bill. I must admit not understanding what you meant about <em>"using the edge of the platform as a pry point for your pliers for compressing the springs"</em> but one glance at your photo and it all makes sense.  :)</p>
]]></description><link>https://multitool.ninja/post/84543</link><guid isPermaLink="true">https://multitool.ninja/post/84543</guid><dc:creator><![CDATA[J-sews]]></dc:creator><pubDate>Sun, 01 Jun 2008 13:43:20 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Sun, 01 Jun 2008 10:35:35 GMT]]></title><description><![CDATA[<p dir="auto">Thanks for that Bill.  :)</p>
<p dir="auto">Very interesting.</p>
]]></description><link>https://multitool.ninja/post/84507</link><guid isPermaLink="true">https://multitool.ninja/post/84507</guid><dc:creator><![CDATA[Benner]]></dc:creator><pubDate>Sun, 01 Jun 2008 10:35:35 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Sun, 01 Jun 2008 08:01:59 GMT]]></title><description><![CDATA[<p dir="auto">Great post mate, very informative :)</p>
]]></description><link>https://multitool.ninja/post/84491</link><guid isPermaLink="true">https://multitool.ninja/post/84491</guid><dc:creator><![CDATA[Mike, Lord of the Spammers!]]></dc:creator><pubDate>Sun, 01 Jun 2008 08:01:59 GMT</pubDate></item><item><title><![CDATA[Reply to SAK Assembler on Sun, 01 Jun 2008 04:20:47 GMT]]></title><description><![CDATA[<p dir="auto">Right Click -&gt; Select All -&gt; Copy -&gt; Save To Desktop.</p>
<p dir="auto">:)</p>
<p dir="auto">Thanks for the information! Althought I am probably quite a way from modding my own SAKs it's really cool of you to show some of the information you had to learn the hard way.</p>
]]></description><link>https://multitool.ninja/post/84465</link><guid isPermaLink="true">https://multitool.ninja/post/84465</guid><dc:creator><![CDATA[Spoonrobot]]></dc:creator><pubDate>Sun, 01 Jun 2008 04:20:47 GMT</pubDate></item></channel></rss>