<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Electrical fun...]]></title><description><![CDATA[<p dir="auto">So to make a relatively long story shorter, the flat next to ours had some recent renovation work done, and while they were knocking out a non-structural brick wall close to the front door (which is beside our front door) the glass lampshade over our entry light jiggled free (I'm actually surprised that's the only thing besides my patience that broke) and crashed to the floor.</p>
<p dir="auto">We went out the other day to the DIY store to look for a simple replacement (it's just the entry way and only used briefly on entering or exiting our flat no need for flashy) and we picked up a pretty basic similar model to what we're replacing. I'm guessing our building is somewhere in it's 30-40s. The wiring in our flat has not been touched for the most part since the day it was built with the exception of some rewiring in the kitchen which was renovated when we moved in about 10 years ago. And I know from experience in the past (trying to swap plugs) that the standards have changed and it's not as easy as swap over. As I gently attempted to disconnect the old socket, I noticed the wiring was quite brittle... not a surprise, and luckily I had previously bought some spools which I had intended to run new wires to our office for the PCs to feed off.</p>
<p dir="auto">One of the good things is that all wiring is run in channels. There are junction boxes in pretty much every room, and some rooms like living/dining have a few. Everything for the most part is easily accessed. Rather somewhat rediculously the nylon wire runner I have is like 20metres long, complete overkill and often gets all twisted up so I have to untangle as I feed. Now I assumed the feed to the light would be from the switch directly to the actual light. Wrong. It would appear that the wire runs across the ceiling and into the <strong>main electrical panel</strong>, and then back out through another channel to the switch, at least one of the wires does.  <img src="/assets/uploads/smileys/facepalm.gif" alt=":facepalm:" title="Facepalm" class="forum-smiley emoji" /> the other ends there connected with all the other lights of our flat on the same (incredibly low rated) breaker... (another project I'd like to do at some point, rerun ALL the wiring, add more breakers on a per room basis perhaps). Safety first of course, flipped off the main feed of the apartment before actually messing with any of this.</p>
<p dir="auto">Obviously I'm not an electrician, however we did do some wiring in electronics class some 25 years ago or so. So rather than change anything dramatically I only replaced like for like with new wires, and hooked it all up. And no surprise, it all works fine. Given that what should be a very simple setup seems overly complicated, I can't imagine how much fun it will be to rewire the whole place!</p>
<p dir="auto">At some point I really do want to sub out all the old plugs/switches for new modern ones, however it will not only require messing with the wiring but also readjusting the plaster around the boxes as the dimensions are different... normally that wouldn't be an issue but in this entire place all the walls and ceilings except kitchen/bathroom are stucco/textured. I personally hate it, but we can't afford to do anything about it right now, and there are other issues that would be prioritized over that. Also I'd like to find some sort of app that would allow me to map the existing wiring before I go changing anything... Ideally it's a project I won't start until I have all the materials and a clear execution plan. Also maybe a safety yoke for my flashlight as I knocked it off the ladder twice this time... the second time it actually broke and I had to use a small flashlight to finish. A quick resolder of the broken wires in my big flashlight had it back up and running in no time.</p>
<p dir="auto">All things said... it took me about two hours to change the bloody entry light on what should have been a quick swap out.  :ahhh</p>
]]></description><link>https://multitool.ninja/topic/59263/electrical-fun</link><generator>RSS for Node</generator><lastBuildDate>Tue, 17 Nov 2026 16:46:43 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/59263.rss" rel="self" type="application/rss+xml"/><pubDate>Tue, 05 May 2015 17:25:45 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Electrical fun... on Tue, 05 May 2015 17:49:07 GMT]]></title><description><![CDATA[<p dir="auto">[everyone in the same volume and tone]</p>
<ul>
<li>Hello Whoey, thanks for sharing!</li>
</ul>
]]></description><link>https://multitool.ninja/post/1083601</link><guid isPermaLink="true">https://multitool.ninja/post/1083601</guid><dc:creator><![CDATA[wmoco]]></dc:creator><pubDate>Tue, 05 May 2015 17:49:07 GMT</pubDate></item></channel></rss>