<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Lansky Standard Sharpening System - WAVE issue]]></title><description><![CDATA[<p dir="auto">Hello, guys, I just bought the Lansky sharpening kit , but reflected a problem with my Wave knife blade. I can't sharpen the blade well because it is small and does not have much on board to be fixed on the support. Plus I do not understand what angle I have to sharpen it, because even using the marker method on the blade, this is taken away, at 25 degrees and also at 30 degrees. To be clear, the two upper holes tool.  <img src="/assets/uploads/smileys/facepalm.gif" alt=":facepalm:" title="Facepalm" class="forum-smiley emoji" /></p>
<p dir="auto">Thank you so much for helping me!  <img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/topic/69488/lansky-standard-sharpening-system-wave-issue</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 00:25:10 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/69488.rss" rel="self" type="application/rss+xml"/><pubDate>Thu, 24 Nov 2016 10:12:25 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Sat, 26 Nov 2016 00:26:13 GMT]]></title><description><![CDATA[<p dir="auto">It is possible that you may have to reprofile the blade as it may not be uniform or even angled on each side.  The way Aloha describes the process to check and sharpen is spot on.</p>
<p dir="auto">The first sharpening may take more time and you may have to use a more course stone to get it beveled correctly too.  If you do have to rebevel the edge to match each side or to get the degree you prefer your edges to be at will also take more time and patience.  Like it was mentioned, I would not go as high as the 30 degree but that too is my opinion.  Stick to either 20 or 25 per side.</p>
]]></description><link>https://multitool.ninja/post/1384978</link><guid isPermaLink="true">https://multitool.ninja/post/1384978</guid><dc:creator><![CDATA[sir_mike]]></dc:creator><pubDate>Sat, 26 Nov 2016 00:26:13 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Fri, 25 Nov 2016 22:23:18 GMT]]></title><description><![CDATA[<p dir="auto">Evil did a good thread on how he's made his Lansky even better.  I like mine very much.  I will also be doing some of Evils mods but in the mean time I really only use mine to RE bevel or even out grinds.</p>
<p dir="auto">Once I've gotten the angle I like ( typically 20 &amp; 25 degrees ) all I really ever do is use my Spyderco Ceramic or Strop to bring back the cutting edge.</p>
<p dir="auto">My SAKs however, a few strokes on either my Spyderco or Lansky ( turn box ) ceramic stones and voila hair popping sharp.</p>
]]></description><link>https://multitool.ninja/post/1384933</link><guid isPermaLink="true">https://multitool.ninja/post/1384933</guid><dc:creator><![CDATA[Aloha]]></dc:creator><pubDate>Fri, 25 Nov 2016 22:23:18 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Fri, 25 Nov 2016 19:47:20 GMT]]></title><description><![CDATA[<p dir="auto">Thanks for that Aloha <img src="/assets/uploads/smileys/like-sign.gif" alt=":like:" title="I like this" class="forum-smiley emoji" /> I rarely use the lanky and I am glad you came in with a more detailed description of how to overcome his issues <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /> Good luck posceve <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/1384843</link><guid isPermaLink="true">https://multitool.ninja/post/1384843</guid><dc:creator><![CDATA[Poncho65]]></dc:creator><pubDate>Fri, 25 Nov 2016 19:47:20 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Thu, 24 Nov 2016 17:58:15 GMT]]></title><description><![CDATA[<p dir="auto">Clamping blades that aren't very wide will be a challenge.  It can be done but the pressure when sharpening will need to be monitored as the clamp grip can and will loosen.  Make sure to note where you clamp so you can re-clamp at the same place.</p>
<p dir="auto">Mark the egde with a sharpie.  Start on the 20 degree and use a light touch to see if that sharpie mark is removed evenly across the bevel.  If you are happy then proceed if not then try the 25 degree.  I would not use the 30 at all, that my opinion.  Keep in mind you may take off material above the sharpie.  This is normal as the factory grind may nt be even across the edge.  The Lansky will event out in most grinds regardless of what initial bevel you had on the knife.</p>
<p dir="auto">For example.  If you have a knife that is set a 25 degree and you prefer a thinner edge you'd go with 20 degree.  The Lansky will level out ( flatten ) the old 25 degree grind to a NEW 20 degree grind removing much of the sharpie marks, tho not at the very edge ( cutting part ) plus much of the shoulder of the old grind.  The sharpie in this case is a reference.  The very edge wont be touched till you flatten the shoulders of the old 25 grind.</p>
<p dir="auto">I hope that made sense.</p>
<p dir="auto">Ask yourself this, what edge angle do you like?  The Lansky system is great at RE- beveling an edge to your desired degree.  It will closely match most edges however there is a bit of variance to the preset angles.  I like to use 20 degree on my Wave and Surge.  Most of my every day edges are also 20 degree give or take a couple degrees.</p>
<p dir="auto">I hope I have helped and not mucked up my attempt at doing so.</p>
<p dir="auto">Take a look at these great links.<br />
/post/1251673</p>
<p dir="auto">This is a terrific video explaining that the angles Lansky has aren't exact.  You can compensate tho and end up with awesome edge.<br />
<a href="https://youtu.be/ZH0ZOjcOZss" rel="nofollow ugc">https://youtu.be/ZH0ZOjcOZss</a></p>
]]></description><link>https://multitool.ninja/post/1384273</link><guid isPermaLink="true">https://multitool.ninja/post/1384273</guid><dc:creator><![CDATA[Aloha]]></dc:creator><pubDate>Thu, 24 Nov 2016 17:58:15 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Thu, 24 Nov 2016 16:17:37 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/neillcurrie" aria-label="Profile: neillcurrie">@<bdi>neillcurrie</bdi></a> <a href="/post/1384114">said</a>:<br />
I've no idea what angle your blade was previously sharpened at, but I sharpen mine using the 20 degree holes in the Lansky.</p>
</blockquote>
<p dir="auto">I'm searching here, and i found that Leatherman use 25/30 degrees angle for a knife blade. My problem it's that i cant sharp. Maybe after i can post a picture for explain better this problem!!</p>
]]></description><link>https://multitool.ninja/post/1384217</link><guid isPermaLink="true">https://multitool.ninja/post/1384217</guid><dc:creator><![CDATA[posceve]]></dc:creator><pubDate>Thu, 24 Nov 2016 16:17:37 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Thu, 24 Nov 2016 14:26:43 GMT]]></title><description><![CDATA[<p dir="auto">You will have to try and get as close to the previous angle as possible with the preset angles in the Lansky and the first time sharpening may take a bit longer but once you get the angle set to one of those it will go much easier <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /> <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /> <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/1384135</link><guid isPermaLink="true">https://multitool.ninja/post/1384135</guid><dc:creator><![CDATA[Poncho65]]></dc:creator><pubDate>Thu, 24 Nov 2016 14:26:43 GMT</pubDate></item><item><title><![CDATA[Reply to Lansky Standard Sharpening System - WAVE issue on Thu, 24 Nov 2016 13:06:12 GMT]]></title><description><![CDATA[<p dir="auto">I've no idea what angle your blade was previously sharpened at, but I sharpen mine using the 20 degree holes in the Lansky.</p>
]]></description><link>https://multitool.ninja/post/1384114</link><guid isPermaLink="true">https://multitool.ninja/post/1384114</guid><dc:creator><![CDATA[neillcurrie]]></dc:creator><pubDate>Thu, 24 Nov 2016 13:06:12 GMT</pubDate></item></channel></rss>