<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Backspring to tool reference guide?]]></title><description><![CDATA[<p dir="auto">Greetings SAK friends.  I have begun modding a half dozen Vic knives and would like to build a 91mm knife to have the clean look of the 93mm backsprings.  With that in mind, I would like to know if I could make my knife configuration using only full-length backsprings and leave off the Awl, Hook, and corkscrew or mid-pivot phillips.  I want to have the following blades/tools on the knife:<br />
Large Blade<br />
Can Opener/(Large Flat Head/Wire Stripper)<br />
Scissors<br />
Pliers<br />
End Pivot Phillips</p>
<p dir="auto">Optional tools (not replacing any of the above)<br />
File<br />
Electrician's knife</p>
<p dir="auto">Also, is there a published reference guide which shows what tools/blades will work with which back springs?</p>
<p dir="auto">Thank you!</p>
]]></description><link>https://multitool.ninja/topic/85955/backspring-to-tool-reference-guide</link><generator>RSS for Node</generator><lastBuildDate>Tue, 17 Nov 2026 20:25:59 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/85955.rss" rel="self" type="application/rss+xml"/><pubDate>Thu, 12 Nov 2020 03:00:29 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Backspring to tool reference guide? on Thu, 12 Nov 2020 05:41:14 GMT]]></title><description><![CDATA[<p dir="auto">Thank you so much Kamakiri.  You have laid out everything for me clearly.  It is obvious that you know so much about these knives/tools and even more obvious that I need to learn a whole heck of a lot more!</p>
<p dir="auto">I appreciate the photo as well.  It is essentially what I am going for.  I have found a scale maker in Germany (w3rktrieb) who will make scales for me without the cutout for the corkscrew.  You have me thinking though.  I might be better off to build out a 93mm knife and start with a Farmer X so I'll have one of the two back springs (from the saw) I'll need for adding pliers.  I don't know how to get an inline Phillips yet but I'd basically have just about everything I want in that configuration.  I've seen a couple that Bob Lessard has done which was my original inspiration for the knife.  I'd basically need to buy a Farmer (I have a new low priductuon run Topo pattern Farmer X en route from a seller in Germany) to get the second saw spring.  Then I'll reshape and add pliers from a 91mm.  Any thoughts you have on which direction you'd take it if you were to build out this particuar configuration?  91mm or 93mm?  I'll be using the same scale maker for either build.</p>
<p dir="auto">Thank you again.</p>
]]></description><link>https://multitool.ninja/post/2178641</link><guid isPermaLink="true">https://multitool.ninja/post/2178641</guid><dc:creator><![CDATA[tlcrawford]]></dc:creator><pubDate>Thu, 12 Nov 2020 05:41:14 GMT</pubDate></item><item><title><![CDATA[Reply to Backspring to tool reference guide? on Thu, 12 Nov 2020 04:17:19 GMT]]></title><description><![CDATA[<p dir="auto">...and you have to figure out what you want to do about the backside scale, since you don’t need the cutout area for the corkscrew.</p>
]]></description><link>https://multitool.ninja/post/2178631</link><guid isPermaLink="true">https://multitool.ninja/post/2178631</guid><dc:creator><![CDATA[kamakiri]]></dc:creator><pubDate>Thu, 12 Nov 2020 04:17:19 GMT</pubDate></item><item><title><![CDATA[Reply to Backspring to tool reference guide? on Thu, 12 Nov 2020 04:27:39 GMT]]></title><description><![CDATA[<p dir="auto">Cool project. You’re gonna need a LOT of vintage tools from before they had backside tools for each layer.</p>
<p dir="auto">Pliers- no problem. None have backside tools.</p>
<p dir="auto">Inline Phillips (2nd) EDIT: no problem if you’re going to include either the magnifier or a Lite module to go on the opposite side.</p>
<p dir="auto">Opener layer- I think the easiest route is a Phillips/magnifier spring and make the seats match the year/style of openers, including milling down to match the thickness.</p>
<p dir="auto">Scissors-  Pre- ‘91 have no hook.</p>
<p dir="auto">Main blade- I think if you flip sides, it should work on a scissor spring with a thin spacer.</p>
<p dir="auto">File can be added with a wood saw spring from either pre-‘85 knife or a Fieldmaster.</p>
<p dir="auto">Small blade can be paired with main blade on a phillips spring and spacers for both sides or mill the spring sides ~0.3mm as needed.</p>
<p dir="auto">An ‘86-‘87 Champ would be a good starting point. The ‘thin’ 2.5mm wide pliers are sleek/clean looking IMO. But any Champ up to ‘90 would work effectively the same.</p>
<p dir="auto"><img src="/assets/uploads/_imported_attachments/migrated/492722_13D53FAF-9F0E-4F77-B41C-E54A62BF4480.jpeg" alt="13D53FAF-9F0E-4F77-B41C-E54A62BF4480.jpeg" class="img-markdown  img-fluid" /></p>
]]></description><link>https://multitool.ninja/post/2178621</link><guid isPermaLink="true">https://multitool.ninja/post/2178621</guid><dc:creator><![CDATA[kamakiri]]></dc:creator><pubDate>Thu, 12 Nov 2020 04:27:39 GMT</pubDate></item></channel></rss>