<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Trouble with oil]]></title><description><![CDATA[<p dir="auto">I have tried all kinds of oil,,including Victorinox brand, and the Vitorinox knives get extremely hard to open and close after I apply the oil.</p>
<p dir="auto">I have tried to give the knives just a small drop of oil, but they still work the same.</p>
<p dir="auto">Oh, yes I have done the Down soap and hot water trick and it brings the knives back to original condition.  There must be something I have not tried.</p>
<p dir="auto">Any help would be appreciated.  Thanks, Bryan</p>
]]></description><link>https://multitool.ninja/topic/87455/trouble-with-oil</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 03:38:15 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/87455.rss" rel="self" type="application/rss+xml"/><pubDate>Mon, 24 May 2021 22:57:03 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Trouble with oil on Thu, 19 Aug 2021 14:12:12 GMT]]></title><description><![CDATA[<p dir="auto">A tip when using oil, use very little.</p>
]]></description><link>https://multitool.ninja/post/2272470</link><guid isPermaLink="true">https://multitool.ninja/post/2272470</guid><dc:creator><![CDATA[Aloha]]></dc:creator><pubDate>Thu, 19 Aug 2021 14:12:12 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Thu, 19 Aug 2021 09:47:04 GMT]]></title><description><![CDATA[<p dir="auto">Wow, I can't believe how much time has passed... Anyway, I noticed this thread: anyway, hot water alone does nothing. In years of refurbishing gritty knives for me and friends, I developed the following procedure:<br />
First I spray the closed knife with kitchen/home degreaser, that white stuff that goes under a number of brands and you use to clean the oven. Then I open the knife and spray it with the kitchen sink water jet. At this point old tootbrushes, toothpicks and pointed chopsticks are used to remove any contamination. At this stage the knife is completely deprived of any lubrication and it is better not to attempt to close it.<br />
The knife is dried with compressed air and soaked in ballistol: this gives back lubrication an helps removing residual water. The SAK can now be closed. At this point I check for any remaining dirt, then I wrap the knife in a rag (old tennis socks or similar) to expel the excess oil. This phase takes about 15 minutes then the knife is ready for final cleaning with a clean rag &amp; application of food grade oil of your preference. A perfect result requires to leave the knife another 24 hours wrapped in kitchen paper to let any remaining ballistol/water come out.</p>
<p dir="auto">Hope it helps.</p>
]]></description><link>https://multitool.ninja/post/2272426</link><guid isPermaLink="true">https://multitool.ninja/post/2272426</guid><dc:creator><![CDATA[GArBa]]></dc:creator><pubDate>Thu, 19 Aug 2021 09:47:04 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Sat, 29 May 2021 07:31:30 GMT]]></title><description><![CDATA[<p dir="auto">Olive oil tends to become sticky and go rancid.</p>
<p dir="auto">Great for salads</p>
]]></description><link>https://multitool.ninja/post/2249169</link><guid isPermaLink="true">https://multitool.ninja/post/2249169</guid><dc:creator><![CDATA[dks]]></dc:creator><pubDate>Sat, 29 May 2021 07:31:30 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Fri, 28 May 2021 15:34:35 GMT]]></title><description><![CDATA[<p dir="auto">used olive oil once in a pinch one time....</p>
<p dir="auto"><img src="/assets/uploads/smileys/facepalm.gif" alt=":facepalm:" title="Facepalm" class="forum-smiley emoji" /></p>
<p dir="auto">It was a mistake.</p>
]]></description><link>https://multitool.ninja/post/2248924</link><guid isPermaLink="true">https://multitool.ninja/post/2248924</guid><dc:creator><![CDATA[Explorer]]></dc:creator><pubDate>Fri, 28 May 2021 15:34:35 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Thu, 27 May 2021 18:54:13 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/aloha" aria-label="Profile: Aloha">@<bdi>Aloha</bdi></a> <a href="/post/2247756">said</a>:<br />
Liner could be interfering?  Could be some corrosion?</p>
<p dir="auto">There was some great advice given in this thread that may help<br />
/topic/87409  <img src="/assets/uploads/smileys/shrugging.gif" alt=":dunno:" title="I dunno" class="forum-smiley emoji" /></p>
<p dir="auto">I use 3in1 oil, mineral oil, and hoppes #9 with no issues.</p>
<p dir="auto">I hope you can figure out whats going on and resolve it.   <img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
</blockquote>
<p dir="auto">Strongly recommend Hoppes #9.</p>
]]></description><link>https://multitool.ninja/post/2248650</link><guid isPermaLink="true">https://multitool.ninja/post/2248650</guid><dc:creator><![CDATA[Knerml]]></dc:creator><pubDate>Thu, 27 May 2021 18:54:13 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Wed, 26 May 2021 02:01:09 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/hardtimeslures" aria-label="Profile: hard.times.lures">@<bdi>hard.times.lures</bdi></a> <a href="/post/2247588">said</a>:<br />
I have tried all kinds of oil,,including Victorinox brand, and the Vitorinox knives get extremely hard to open and close after I apply the oil.</p>
<p dir="auto">I have tried to give the knives just a small drop of oil, but they still work the same.</p>
<p dir="auto">Oh, yes I have done the Down soap and hot water trick and it brings the knives back to original condition.  There must be something I have not tried.</p>
<p dir="auto">Any help would be appreciated.  Thanks, Bryan</p>
</blockquote>
<p dir="auto">I don’t think it’s the oil. I primarily use the Victorinox oil and never ever had it <em>cause</em> a problem on any knife. It’s also never ‘allowed’ a fixed stiff knife to go back to being stiff.</p>
<p dir="auto">But one thing I would suggest, is to stop using the hot water. I suppose it temporarily helps loosen things up with the heat by expanding things enough to operate...but ultimately increasing the corrosion and oxides which as far as I know do cause knives to get unusable. And I’m guessing that’s what’s happening after the knife cools down and gets oiled.</p>
<p dir="auto">For what it’s worth, I only use water on individual tools and only rarely for whole knives if too dirty to disassemble without a soaking first.</p>
<p dir="auto">It’s my opinion that this issue is worse on modern knives that don’t have all anodized liners. Those seem to have lots of other issues when they get corroded.</p>
<p dir="auto">That aside, I suggest using mechanical means to help stretch the pins where they are worst. In extreme cases I’ve used (old) blades as a wedge between the tight tools and the adjacent liners to create enough loosening to clean the internal corrosion. Another quick trick I use to clean out corrosion is to use a tiny bit of clay to help degrade and displace the oxides. Ironically, that’s one time I do use water...to wash the clay out.</p>
<p dir="auto">Good luck with a more permanent solution.</p>
]]></description><link>https://multitool.ninja/post/2247987</link><guid isPermaLink="true">https://multitool.ninja/post/2247987</guid><dc:creator><![CDATA[kamakiri]]></dc:creator><pubDate>Wed, 26 May 2021 02:01:09 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 15:24:36 GMT]]></title><description><![CDATA[<p dir="auto">Liner could be interfering?  Could be some corrosion?</p>
<p dir="auto">There was some great advice given in this thread that may help<br />
/topic/87409  <img src="/assets/uploads/smileys/shrugging.gif" alt=":dunno:" title="I dunno" class="forum-smiley emoji" /></p>
<p dir="auto">I use 3in1 oil, mineral oil, and hoppes #9 with no issues.</p>
<p dir="auto">I hope you can figure out whats going on and resolve it.   <img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/2247756</link><guid isPermaLink="true">https://multitool.ninja/post/2247756</guid><dc:creator><![CDATA[Aloha]]></dc:creator><pubDate>Tue, 25 May 2021 15:24:36 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 14:34:22 GMT]]></title><description><![CDATA[<p dir="auto">Thank you for your replies.  Bryan</p>
]]></description><link>https://multitool.ninja/post/2247736</link><guid isPermaLink="true">https://multitool.ninja/post/2247736</guid><dc:creator><![CDATA[hard.times.lures]]></dc:creator><pubDate>Tue, 25 May 2021 14:34:22 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 13:22:16 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/dks" aria-label="Profile: dks">@<bdi>dks</bdi></a> <a href="/post/2247653">said</a>:<br />
It could be dust or pocket lint mixing with the oil, making the blades hard to open.</p>
<p dir="auto">Try without any oil and see what happens</p>
</blockquote>
<p dir="auto"><img src="/assets/uploads/smileys/agreesign.gif" alt=":iagree:" title="I agree" class="forum-smiley emoji" /> This is a good point.  I make sure to clean thoroughly before lubricating.  Truth be told, I probably only lubricate most of my users once a year or so.  Most of them just don't need it unless they've gotten especially dirty.</p>
]]></description><link>https://multitool.ninja/post/2247717</link><guid isPermaLink="true">https://multitool.ninja/post/2247717</guid><dc:creator><![CDATA[NutSAK]]></dc:creator><pubDate>Tue, 25 May 2021 13:22:16 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 06:45:52 GMT]]></title><description><![CDATA[<p dir="auto">It could be dust or pocket lint mixing with the oil, making the blades hard to open.</p>
<p dir="auto">Try without any oil and see what happens</p>
]]></description><link>https://multitool.ninja/post/2247653</link><guid isPermaLink="true">https://multitool.ninja/post/2247653</guid><dc:creator><![CDATA[dks]]></dc:creator><pubDate>Tue, 25 May 2021 06:45:52 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 01:07:02 GMT]]></title><description><![CDATA[<p dir="auto">I also use a mineral oil, though not very often.  A drop is too much though; I smear a small amount on the back of the tang with a toothpick, then open and close the blade a couple of times to work it in.</p>
]]></description><link>https://multitool.ninja/post/2247610</link><guid isPermaLink="true">https://multitool.ninja/post/2247610</guid><dc:creator><![CDATA[nate j]]></dc:creator><pubDate>Tue, 25 May 2021 01:07:02 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 00:55:17 GMT]]></title><description><![CDATA[<p dir="auto"><img src="/assets/uploads/smileys/agreesign.gif" alt=":iagree:" title="I agree" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/2247609</link><guid isPermaLink="true">https://multitool.ninja/post/2247609</guid><dc:creator><![CDATA[Nix]]></dc:creator><pubDate>Tue, 25 May 2021 00:55:17 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 00:52:32 GMT]]></title><description><![CDATA[<p dir="auto">I should have mentioned that I default to mineral oil because it's food safe. I like to keep my blades clean and ready for food prep whenever needed.</p>
]]></description><link>https://multitool.ninja/post/2247607</link><guid isPermaLink="true">https://multitool.ninja/post/2247607</guid><dc:creator><![CDATA[NutSAK]]></dc:creator><pubDate>Tue, 25 May 2021 00:52:32 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Tue, 25 May 2021 00:24:31 GMT]]></title><description><![CDATA[<p dir="auto">I use Rem Oil. I figure if it is good enough for the firearms, it should be good enough for the SAKs. No complaints yet.</p>
]]></description><link>https://multitool.ninja/post/2247603</link><guid isPermaLink="true">https://multitool.ninja/post/2247603</guid><dc:creator><![CDATA[Chako]]></dc:creator><pubDate>Tue, 25 May 2021 00:24:31 GMT</pubDate></item><item><title><![CDATA[Reply to Trouble with oil on Mon, 24 May 2021 23:32:30 GMT]]></title><description><![CDATA[<p dir="auto">I haven't experienced the issue you're having. I use mineral oil. If it's a particularly tight knife I use Nano-oil. Rarely have I had a particularly tight Victorinox unless it was damaged or very old.</p>
]]></description><link>https://multitool.ninja/post/2247596</link><guid isPermaLink="true">https://multitool.ninja/post/2247596</guid><dc:creator><![CDATA[NutSAK]]></dc:creator><pubDate>Mon, 24 May 2021 23:32:30 GMT</pubDate></item></channel></rss>