<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Swapping the corkscrew/phillips on a SAK - A how to.]]></title><description><![CDATA[<p dir="auto">As requested by max6166 here's a quick run down of how to replace a corkscrew with a phillips driver on a SAK.  In this case a Waiter.  I've shown these pics before in some ancient thread but I can't find it  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /> so here they are again :)</p>
<p dir="auto">Step 1 - remove the scales of your victim</p>
<p dir="auto"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/wm1.jpg" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Step 2 - file off the head of the corkscrew pin, you can also drill it out if you're careful</p>
<p dir="auto"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/wm2.jpg" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Step 3 - using a small nail or punch smaller than the pin, knock the pin out. At this stage the backspring will shift out of place. Panic not, slot your previously extracted screwdriver into place as best you can and then use a vice to compress the arrangement until the pin holes all line up.</p>
<p dir="auto"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/wm3.jpg" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Step 4 - take a small piece of 2.25mm diameter brass rod that you've tapered a little at one end and gently tap into through the hole. Once its in you can release the knife from the vice</p>
<p dir="auto"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/wm4.jpg" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Step 5 - now snip, cut or saw off the brass rod until you have around 1.5mm proud of either side (hint, dremell cut off wheel is good) and begin peening.  Do not over peen, keep checking the action to make sure you don't do it too tight.</p>
<p dir="auto"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/wm5.jpg" alt="" class="img-markdown  img-fluid" /></p>
<p dir="auto">Step 6 - rescale and admire your handiwork. Or if you overdid the peening go back to step 2 :)</p>
<p dir="auto"><a href="http://s303.photobucket.com/albums/nn153/NKB_Pocket_Tools/?action=view&amp;current=simple-waiter-mod-1.jpg" rel="nofollow ugc"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/th_simple-waiter-mod-1.jpg" alt="" class="img-markdown  img-fluid" /></a> click for big versions <a href="http://s303.photobucket.com/albums/nn153/NKB_Pocket_Tools/?action=view&amp;current=simple-waiter-mod-2.jpg" rel="nofollow ugc"><img src="http://i303.photobucket.com/albums/nn153/NKB_Pocket_Tools/th_simple-waiter-mod-2.jpg" alt="" class="img-markdown  img-fluid" /></a></p>
<p dir="auto">Step 7 - Share with us how it turned out  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">Neil</p>
]]></description><link>https://multitool.ninja/topic/9057/swapping-the-corkscrewphillips-on-a-sak-a-how-to</link><generator>RSS for Node</generator><lastBuildDate>Mon, 16 Nov 2026 11:44:32 GMT</lastBuildDate><atom:link href="https://multitool.ninja/topic/9057.rss" rel="self" type="application/rss+xml"/><pubDate>Mon, 02 Feb 2009 19:46:24 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Thu, 30 Apr 2009 18:40:26 GMT]]></title><description><![CDATA[<p dir="auto">I've been scratching my head a little wondering if this was possible, and lo, Neil has already figured it out, posted a tutorial and put my head scratching to bed  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/200995</link><guid isPermaLink="true">https://multitool.ninja/post/200995</guid><dc:creator><![CDATA[nuphoria]]></dc:creator><pubDate>Thu, 30 Apr 2009 18:40:26 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 10 Feb 2009 16:40:14 GMT]]></title><description><![CDATA[<p dir="auto">Exactly.  I hadn't heard of the Apprentice until I looked at the list on the SAKwiki.  Your tutorial happily coincided with a small Tinker coming up on eBay and so it all seems a bit serendipitous not to do one.  Plus I can put together a Tourist, another 84mm I don't have.  :D</p>
]]></description><link>https://multitool.ninja/post/169477</link><guid isPermaLink="true">https://multitool.ninja/post/169477</guid><dc:creator><![CDATA[Gareth]]></dc:creator><pubDate>Tue, 10 Feb 2009 16:40:14 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 10 Feb 2009 15:55:50 GMT]]></title><description><![CDATA[<p dir="auto">It is one of those tool combinations that I'm surprised is no longer available.</p>
<p dir="auto">Neil</p>
]]></description><link>https://multitool.ninja/post/169465</link><guid isPermaLink="true">https://multitool.ninja/post/169465</guid><dc:creator><![CDATA[Neil]]></dc:creator><pubDate>Tue, 10 Feb 2009 15:55:50 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 10 Feb 2009 15:48:53 GMT]]></title><description><![CDATA[<p dir="auto">well I liked the look of this so much I've got a Tinker Small on the way to do one for myself.  :D</p>
]]></description><link>https://multitool.ninja/post/169463</link><guid isPermaLink="true">https://multitool.ninja/post/169463</guid><dc:creator><![CDATA[Gareth]]></dc:creator><pubDate>Tue, 10 Feb 2009 15:48:53 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 20:41:20 GMT]]></title><description><![CDATA[<p dir="auto">Great tutorial Neil thank you  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /> <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" />, keep em coming  <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166989</link><guid isPermaLink="true">https://multitool.ninja/post/166989</guid><dc:creator><![CDATA[donvito]]></dc:creator><pubDate>Tue, 03 Feb 2009 20:41:20 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 19:45:27 GMT]]></title><description><![CDATA[<p dir="auto">Great job on that, and that I would say is the perfect off day Sak!</p>
<p dir="auto">Now make me one!</p>
]]></description><link>https://multitool.ninja/post/166969</link><guid isPermaLink="true">https://multitool.ninja/post/166969</guid><dc:creator><![CDATA[hawkchucker]]></dc:creator><pubDate>Tue, 03 Feb 2009 19:45:27 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 12:27:37 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/neil" aria-label="Profile: NKB">@<bdi>NKB</bdi></a> <a href="/post/166752">said</a>:</p>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/glorn" aria-label="Profile: glorn">@<bdi>glorn</bdi></a> <a href="/post/166720">said</a>:</p>
<blockquote>
<p dir="auto">Excellent! Thanks!<br />
Now.. could you show us how to swap the Phillips for a corkscrew?  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /></p>
<p dir="auto">;)</p>
</blockquote>
<p dir="auto">::)  :D</p>
<p dir="auto">Mike, I will do something for Sosakonline just don't hold me to a time frame :)</p>
<p dir="auto">Neil</p>
</blockquote>
<p dir="auto">Good man <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166805</link><guid isPermaLink="true">https://multitool.ninja/post/166805</guid><dc:creator><![CDATA[Mike, Lord of the Spammers!]]></dc:creator><pubDate>Tue, 03 Feb 2009 12:27:37 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 11:53:31 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/gareth" aria-label="Profile: Gareth">@<bdi>Gareth</bdi></a> UK <a href="/post/166793">said</a>:</p>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/benner" aria-label="Profile: Benner">@<bdi>Benner</bdi></a> <a href="/post/166787">said</a>:</p>
<blockquote>
<p dir="auto">Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.</p>
</blockquote>
<p dir="auto">You'll see that on newer knives.  I don't know when exactly but Vic started making their blade tangs slimmer a few years back.  Rather than put a spacer next to the blade they put that indent into the scale.  I'm not sure I've explained that very well.  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /></p>
</blockquote>
<p dir="auto">No I get ya!  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">Thanks for that.</p>
]]></description><link>https://multitool.ninja/post/166794</link><guid isPermaLink="true">https://multitool.ninja/post/166794</guid><dc:creator><![CDATA[Benner]]></dc:creator><pubDate>Tue, 03 Feb 2009 11:53:31 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 11:51:42 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/benner" aria-label="Profile: Benner">@<bdi>Benner</bdi></a> <a href="/post/166787">said</a>:<br />
Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.</p>
</blockquote>
<p dir="auto">You'll see that on newer knives.  I don't know when exactly but Vic started making their blade tangs slimmer a few years back.  Rather than put a spacer next to the blade they put that indent into the scale.  I'm not sure I've explained that very well.  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166793</link><guid isPermaLink="true">https://multitool.ninja/post/166793</guid><dc:creator><![CDATA[Gareth]]></dc:creator><pubDate>Tue, 03 Feb 2009 11:51:42 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 11:35:54 GMT]]></title><description><![CDATA[<p dir="auto">Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.</p>
]]></description><link>https://multitool.ninja/post/166787</link><guid isPermaLink="true">https://multitool.ninja/post/166787</guid><dc:creator><![CDATA[Benner]]></dc:creator><pubDate>Tue, 03 Feb 2009 11:35:54 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 09:52:43 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/glorn" aria-label="Profile: glorn">@<bdi>glorn</bdi></a> <a href="/post/166720">said</a>:<br />
Excellent! Thanks!<br />
Now.. could you show us how to swap the Phillips for a corkscrew?  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /></p>
<p dir="auto">;)</p>
</blockquote>
<p dir="auto">::)  :D</p>
<p dir="auto">Mike, I will do something for Sosakonline just don't hold me to a time frame :)</p>
<p dir="auto">Neil</p>
]]></description><link>https://multitool.ninja/post/166752</link><guid isPermaLink="true">https://multitool.ninja/post/166752</guid><dc:creator><![CDATA[Neil]]></dc:creator><pubDate>Tue, 03 Feb 2009 09:52:43 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Tue, 03 Feb 2009 04:15:42 GMT]]></title><description><![CDATA[<p dir="auto">Excellent! Thanks!</p>
<p dir="auto">Now.. could you show us how to swap the Phillips for a corkscrew?  <img src="/assets/uploads/smileys/thinking.gif" alt=":think:" title="Thinking" class="forum-smiley emoji" /></p>
<p dir="auto">;)</p>
]]></description><link>https://multitool.ninja/post/166720</link><guid isPermaLink="true">https://multitool.ninja/post/166720</guid><dc:creator><![CDATA[glorn]]></dc:creator><pubDate>Tue, 03 Feb 2009 04:15:42 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 21:59:17 GMT]]></title><description><![CDATA[<p dir="auto">Cool thanks for that Neil <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /> Very informative and clear :)</p>
]]></description><link>https://multitool.ninja/post/166511</link><guid isPermaLink="true">https://multitool.ninja/post/166511</guid><dc:creator><![CDATA[Poncho65]]></dc:creator><pubDate>Mon, 02 Feb 2009 21:59:17 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 21:17:23 GMT]]></title><description><![CDATA[<p dir="auto">Nice trick that Neil - nice one!</p>
]]></description><link>https://multitool.ninja/post/166493</link><guid isPermaLink="true">https://multitool.ninja/post/166493</guid><dc:creator><![CDATA[DaveK]]></dc:creator><pubDate>Mon, 02 Feb 2009 21:17:23 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 21:09:13 GMT]]></title><description><![CDATA[<p dir="auto">Damn fine tutorial mate <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">If you've got time, maybe you could do some for Sosakonline :)</p>
]]></description><link>https://multitool.ninja/post/166489</link><guid isPermaLink="true">https://multitool.ninja/post/166489</guid><dc:creator><![CDATA[Mike, Lord of the Spammers!]]></dc:creator><pubDate>Mon, 02 Feb 2009 21:09:13 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 20:22:19 GMT]]></title><description><![CDATA[<p dir="auto">Making it an Apprentice.  <a href="http://www.sakwiki.com/tiki-index.php?page=Apprentice+Victorinox" rel="nofollow ugc">http://www.sakwiki.com/tiki-index.php?page=Apprentice+Victorinox</a></p>
<p dir="auto">Great tutorial; nice and clear.  Also a great little knife.  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166460</link><guid isPermaLink="true">https://multitool.ninja/post/166460</guid><dc:creator><![CDATA[Gareth]]></dc:creator><pubDate>Mon, 02 Feb 2009 20:22:19 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 20:07:39 GMT]]></title><description><![CDATA[<p dir="auto">Great tutorial buddy.  <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166456</link><guid isPermaLink="true">https://multitool.ninja/post/166456</guid><dc:creator><![CDATA[Benner]]></dc:creator><pubDate>Mon, 02 Feb 2009 20:07:39 GMT</pubDate></item><item><title><![CDATA[Reply to Swapping the corkscrew/phillips on a SAK - A how to. on Mon, 02 Feb 2009 20:02:06 GMT]]></title><description><![CDATA[<p dir="auto">What a great tutorial, Neil! I am sure many people will find this very useful. Thank you very much for posting it.  <img src="/assets/uploads/smileys/cheers.gif" alt=":cheers:" title=":cheers:" class="forum-smiley emoji" /></p>
]]></description><link>https://multitool.ninja/post/166455</link><guid isPermaLink="true">https://multitool.ninja/post/166455</guid><dc:creator><![CDATA[max6166]]></dc:creator><pubDate>Mon, 02 Feb 2009 20:02:06 GMT</pubDate></item></channel></rss>