Skeletool loose bit holder
-
I took a LM Skeletool on holiday with me along with plenty of other tools but I wanted to test the Skeletool out and take a close look at it . One thing that quickly came too light was the spare bit wasn't held in very securley and with one sharp tap on my hand it would fall out :( Not good if your working on something and you drop the tool . A dark night with water about and a LM bit changer don't mix anyway but thats another story . I thought about wrapping bits of paper around the spare bit and it does work but its a bit of a pain and you shouldnt need to do it .
I only went 50 miles up the coast but its a change on the eyes and the coastline is very different but I know the area and my wife and I are very fond of the local villages .Ok I know you all want to know how I fixed the Skeletool ::) But I'm going to make you suffer by hearing my drivling little stories >:D
It all started when the clip came loose :( I didnt have a correct bit to fit it so I made a post on here asking about the correct size bit and ratflash7 replied and told me it was a #8 Torx ( thanks btw ) . So everyday that we went out I kept an eye open for somewhere that may sell torx bits . It was quite funny because my wife thought I was going up all these little streets looking for cute ornaments for our home >:D One day we were in a village called Wells which is quite famous in these neck of the woods and has ties with Lord Nelson , it is said he was a guest of his Brothers at a Gentlemans club there ( no not that sort of club
) on a couple of occasions . Anyway I found this fishing tackle shop that also had a very good range of Leathermans at the usual rip off Britain prices :( but they also had a 32 piece security bit set for £5 ( trust me thats a good price here ) . A quick check on the back confirmed it contained a Torx #8 and one fiver later it was mine :D
Back at the cottage the clip screw was quickly tightened .I remember Speaking to DaveK via PM about the loose clip and he thought that it might be a contributing factor to the loose bit holder because they are on the same handle and bolt . Made sense too me but only made a tiny bit of difference when I tightened up the clip :( Not good I thought .So Gentlemen you will need a #8 torx bit , I got on fine with just one but its best to use two ( one for each side because they can spin ) . Hold the tool so the Bit holder is uppermost ( forget about the clip ) with the screw at the top . Undo it and remove it along with the collar/washer . Now rotate out the metal bar that retains the spare bit . Now very slightly bend it inwards ( see pics ) . Don't go mad just a little , remember you can always undo the screw and bend it a bit more if you haven't done it enough .Rotate the bar back in place and replace the washer/collar and tighten screw . Don't tighten the screw up hard as you wont be able to open the blade . Just a little at a time and you can get the blade with the exact right tension to suit you . Since doing this two weeks ago none of the screws have come loose . If they did then I would use a little Loctite . My spare bit is just right now and I'm really happy with it . But please remember that you do this at your own risk and neither me or Multitool.org can be held responsible for anything you cock up ::)
So there you go :) I told you I would make you suffer :D Just be thankfull I havent posted pics of the Village I bought the bits in :D




Dunc
-
Thanks Dunc.....you made that clear and easy. Now i just have to wait for my skeletool........

-
Great tutorial mate :)
-
Great post and pics!

-
-
This is no use to me! I don't have one. Actually, I don't think I want one. I keep passing up the Shnoop deals. =(
-
-
So Dunc - do you think the bit holder was loose because it got dinged or something? If you had to bend it rather than just tighten it, it sounds as though one of the component parts was damaged in some way I guess.
-
@DaveK said:
So Dunc - do you think the bit holder was loose because it got dinged or something? If you had to bend it rather than just tighten it, it sounds as though one of the component parts was damaged in some way I guess.No not at all . The bar needed bending inwards , so if it had been dinged it may have had the same result . I had been over this tool with a magnifying glass ( like all my tools ) and absolutely no dings .
Its great now , although you can't see any difference . The bend is very subtle .Dunc
-
The reason I ask is on mine (without any fiddling performed upon it), the SS bar that holds the bit is really quite taught.
Looking really closely, the inserted bit actually lifts the SS bar ever so slightly, so that it doesn't touch the aluminium strip until half way to the rivet (dunno if you can picture it from that description).
Any way - the point is that inserting the bit pushes the bar so that creates the tension that holds it in place - so I'm wondering where the "difference" was with yours, as it seems pretty simple and reliable.
I'll see if I can get a decent pic to illustrate ......
-
Yes please do take some pics , I will take some more of mine looking down the tool . Looking at it you cant see its been bent .like I said its very subtle but enough to work .
Dunc
-
Ok - hopefully you can see from this:

So, if yours wasn't gripping the bit tightly enough, there seems to be two likely possible reasons:
-
The bar was bent (which you've confirmed it wasn't);
-
The tool maybe wasn't "square" meaning that the bar wasn't parallel to the aluminium spacer somehow. I wonder therefore of it was related to the loose clip, and simply something wasn't tightened to the right torque in the factory?
I know I'm only guessing, but it would be interesting to know if the two problems always go hand in hand

-
-
After I tightened the clip it made a tiny bit of difference but not enough , the bit would still come out after a sharp tap on the hand . But after removing the screw and bending the bar its now perfect .


Dunc
-
Look at all 'dem security drivers.
If I saw you about town with that I'd be right suspicious I would.
-
-
Not to worry about the locking one hander I have clipped to my pocket
Heh, reminds me about visiting the pub
"Hey mate, you got steel caps on?"
"eh, yes."
"You can't wear steelcaps at the pub mate, It's all right this time, just remember though."
(Guess I won't mention all the knives then ::) )
Having built the bugger apart, does it seem like there is room for more models/variations using the same chassis? (Probably not as modular as a Juice, but could they make some more designs using the same equipment)
-
Not to worry about the locking one hander I have clipped to my pocket
Having built the bugger apart, does it seem like there is room for more models/variations using the same chassis? (Probably not as modular as a Juice, but could they make some more designs using the same equipment)
I hope so , if they could somehow fit scissors in there then I think they would be onto a sure winner .
Dunc
-
Nomad what are steel caps? ???
A few hours ago I unscrewed the bolt and bent the metal retaining strip, and the bit sits a lot more firlmy in it's compartment now

-
Nice simple solution Dunc--bravo!

I don't have a Skeletool yet, but I'll sure keep this in mind when I do.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login