Yet another PST Restoration Thread
-
I recently acquired a PST from ebay. The listing said that there was "some rust" on one side of the tool, but on the other side it had rusted so badly that the seller couldn't actually get the tools to open.
Well, I like a challenge, and it arrived yesterday.
I couldn't get the tools on the side with the file to open either, totally seized up with rust, so it was a WD40 bath, and then out with the Crunch and Kick pocket clips to start taking it apart.


I've done a few of these now, but usually, the rust is just near the surface and can be removed fairly easily. Not so with this one. The previous owner said that it had been in his shed for at least 5 years, and this made for the worst condition PST I've ever seen!
Totally disassembled it looked pretty horrible:


With hindsight, I should have taken a few more "before" photos, but I was determined to get it finished last night and forgot to take any. I did get these though, showing the clip point blade before and after:

As usual, the biggest challenge for rust removal is always the file, but I had a decent crack at it, and whilst there are still clear marks. it's perfectly acceptable and useable as I hope the below pictures show.



I managed to assemble it without damage to the knurled screws, and used a fine grit sandpaper to remove some of the deeper scratches on the handles, and I hope you'll agree that this is now a nice little tool again. Several hours work, and worth every bit of it to me.
PSTs never die, they just need a little bunk-up from time to time ;)
-
Great work there Dave.

You gotta love the PST. :)
-
Good job there mate

Another one rescued :)
-
great work mate

-
A job well done, and even without the proper tools.

This one will go many miles again before it needs it's next tune-up.
My guess is that someone is going to be very happy with this one in the near future.This is also some sort of hobby of mine too, restoring older tools to their former glory, or at least to a workable existence again.
But it's much easier when you have a good set of tools and a reasonable supply of new original parts, :D -
It's always nice to see new life pumped into such a pedigree,thanks for the post and pic's!!!

-
@kwakster said:
A job well done, and even without the proper tools.
This one will go many miles again before it needs it's next tune-up.
My guess is that someone is going to be very happy with this one in the near future.This is also some sort of hobby of mine too, restoring older tools to their former glory, or at least to a workable existence again.
But it's much easier when you have a good set of tools and a reasonable supply of new original parts, :DHaha - I bet it is!
That reminds me - PM on way..... ;)
-
Great thread Dave
You've done a great job . You are probably the top UK bloke for LM resuscitation ;)Dunc
-
Great restoration effort on that one Dave! 8)
I enjoyed your comment about the file - every other part can be polished to an unblemished condition except a file. Getting the rust bogeys out of the teeth can be maddening, and one always has to settle for "good enough" it seems. :P I use a fine wire brush, then a stiff toothbrush, with plenty of gun oil/solvent. -
Dunc - I'm probably the ONLY UK bloke for LM Restoration.... oh.... :D
Bob - the file is a PITA if the rust has gotten hold. This one was rusted shut, so anything barely presentable was a result. Myself, I tend to use loads of WD40, wire wool, and then finally scratch out anything that will move from between the grooves with a smaller blade (micra, sak, whatever's nearest). If you spend long enough at it, you can get some decent results.
Not particularly enjoyable work though the files.
-
Dave,
Looks great....you are a patient man

Whats your secret to removing rust?
-
No secret Flash, WD40, fine grit sandpaper (I used 1000 grit on this one) and loads of patience.
I actually find this sort of thing therapeutic, so yesterday I was on here whilst rolling various components in sandpaper at the same time.
You should try it. Pick up a manky PST from ebay. Probably one that everyone else has left well alone :D, and give it a go. It's very rewarding.
-
My respects Dr Davek, I would have fainted at the sight of so much bl...rust
:DSeriously a restoration job to be proud of
-
Another tool saved... by spending <u>way</u> too much time restoring it. Just do a single hours overtime and buy one in good condition instead :P
I even here some idiots do this with old SAKs ::) ... ... oh...
;)Very nice job mate

Neil
-
@NKB said:
Another tool saved... by spending <u>way</u> too much time restoring it. Just do a single hours overtime and buy one in good condition instead :PI even here some idiots do this with old SAKs ::) ... ... oh...
;)Very nice job mate

Neil
Lol yeah. I don't think there's a living in this somehow, but I do enjoy doing it.
-
This may be a dumb question, but I noticed the specialized wrenches used on the knurled screws here, and I gotta know where I can get a couple. Any help, pms, or offers would be greatly appreciated.
P.S. Awesome restoration job, man.

STik -
@STik said:
This may be a dumb question, but I noticed the specialized wrenches used on the knurled screws here, and I gotta know where I can get a couple. Any help, pms, or offers would be greatly appreciated.
P.S. Awesome restoration job, man.

STikgreat job and always a pleasure to have accompanying pictures! I echo the wrench enquiry.
sean
-
Awesome job, Dave!
I love to see great tools rescued. ;) -
Those "wrenches" are actually Kick pocket clips. Dave mentioned it in his original post but I know it is kinda stealthy if you haven't seen this thing before... :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
