Babola's Acid Wave project
-

So I just send you my Wave? Or is there some other method?
I am guessing this is for someone else since all you own are Surge's?

Good looking job by the way.
-
So I just send you my Wave? Or is there some other method?
I am guessing this is for someone else since all you own are Surge's?

Good looking job by the way.
Haha, thanks. I do own number of modded Waves too, not just Surges ;)
-
Here's all the bits lined up together, awaiting assembly.
Well, all except the scissors, they are shown by mistake as I will be swapping them with an awl.

Although it doesn't show well on the photo I polished a living daylight out of those spacers and washers, they're very smooth now.
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

-
You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
Right.
I was just wondering because I am planning my Wave mods.
You ever do work for other people?
-

You could switch out the small driver for the awl also right?
I see you got the Rebar head too.

Sure you can, they're the same size. However I find myself using small 2-way driver more often than scissors. 8)
Right.
I was just wondering because I am planning my Wave mods.
You ever do work for other people?
Unless you're Downunder the whole excersize becomes cost prohibitive. Ancient NZ postal practices (read: exorbitant eye gouging on registered/courier International shipping cost) kill all the fun. :(
-
looks awesome so far.

-
Finished product! :ahhh
Please meet 'Acid Wave'




-
Nice job !
-
I like the look!

-
Thanks guys!
Included few more photos below.
Re-profiled Rebar awl:


The finish is sort of subdued gray, the stonewash texture is visible under angle. There is also a little bit of surface 'sparkle'.

Pliers and awl borrowed from Rebar, Wave scissors removed and used for another project.
All fits well after awl re-profiling.

-
@HarleyXJGuy said:
The awl has to be messed with for it to fit on a Wave?Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
So you do not need to mess with the sharp part, you can shave it off the back?
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
So you do not need to mess with the sharp part, you can shave it off the back?
Correct. The total awl's length is unchanged.
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
So you do not need to mess with the sharp part, you can shave it off the back?
Correct. The total awl's length is unchanged.
Thanks.
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
I like the slimmer version of the awl too! :D and there's certainly some satisfaction to be had when you do another test fit and the handles close nicely without that gap. ;)
really nice work on this mod... I love the way it turned out!

just out of curiosity -- do the handles have a different texture to them now? I had the handles cerakoted for one of my Wave mods, and I really liked the feel of the handles after cerakoting.
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
I like the slimmer version of the awl too! :D and there's certainly some satisfaction to be had when you do another test fit and the handles close nicely without that gap. ;)
really nice work on this mod... I love the way it turned out!

just out of curiosity -- do the handles have a different texture to them now? I had the handles cerakoted for one of my Wave mods, and I really liked the feel of the handles after cerakoting.
Thanks M

The awl now reminds me of the SAK awl a little bit, not that I was going for that look but it turned out that way in the end.
The texture is now actually very smooth, silky even. After the initial acid treatment the feel is rough, almost sandpaper 1000 grit like. However, stone washing process de-burrs the edges a little and smooths out the surface, so it's almost slippery on touch now :)
-
The awl has to be messed with for it to fit on a Wave?
Yes, by about 1mm that needs to be 'shaved' off the top arch. Otherwise the pliers head interferes with it on closing the handles leaving an unsightly gap between the handles.
Strangely enough, I prefer this thin-profile awl look to the original one. ::)
I like the slimmer version of the awl too! :D and there's certainly some satisfaction to be had when you do another test fit and the handles close nicely without that gap. ;)
really nice work on this mod... I love the way it turned out!

just out of curiosity -- do the handles have a different texture to them now? I had the handles cerakoted for one of my Wave mods, and I really liked the feel of the handles after cerakoting.
Breeze you have any extra Rebars laying around?

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login