The Hacked Leatherman Owners Club.
-
Cool mod!
Nate
Thanks.

I really like what you did with the screws!
-
So this is work in process...
I can tell you that I like it and most of all I like doing it. Its a bit out of my comfort zone my first project working with metal.



-
@Etherealicer said:
So this is work in process...I can tell you that I like it and most of all I like doing it. Its a bit out of my comfort zone my first project working with metal.
That is cool.
Welcome to the club.
Will you cut down the fasteners once you make some scales? -
So this is work in process...
I can tell you that I like it and most of all I like doing it. Its a bit out of my comfort zone my first project working with metal.
That is cool.
Welcome to the club.
Will you cut down the fasteners once you make some scales?Well, what are the fasteners you are talking about ??? :P
That said, I make it up as I go, so I don't know yet.
Next step is to use a router (is that the right word) to make a center liner... probably make it first of Aluminum if that works out I will make it out of carbon fiber. -
I made a small adjustment to the PST III mod of mine this weekend. Here it is before I tweaked it ...

The SOG scissors actually worked quite well in the PST frame, and didn't suffer as much from being "upside down" as they do in a SOG Powerlock frame. For those who weren't aware, they're kind of an outboard scissor configuration for inboard tools, which means the scissors lever goes the opposite direction to all other scissors. With the PST frame being so thin, this didn't matter so much when using the scissors, but when you weren't using the scissors they were a little too broad to fully stom into the handles. This meant that the tool never really closed properly.
I decided to switch these out for Fuse scissors, and found that actually created enough room to get an awl in there too. Here it is after the re-hash ...
Seems to be working out quite well. The drivers deploy slightly ... well .. overdeployed, by which I mean they go beyond stright with the body of the tool, but I don't find that a problem at all. In fact if you are just nipping up a loose screw, it can actually be a bit of a benefit. This tool originally came about because a while back I had an empty PST II frame after fitting all the innards into a PT-510 (which is now lost, or I believe may have actually been stolen from me at work), and so I fitted in whatever I had lying around go get it back carryable again. Overall I'm a lot happier with it like this than with the SOG scissors, and this actually gets a little more carry time than my original layout PST with pocket clip attached, mainly due to the scissors and serrated blade to accompany whatever plain edge knife I have on me at the time
-
-
Not got my digital calipers at the moment, but it's around 14mm
-
@50ft-trad said:
I made a small adjustment to the PST III mod of mine this weekend. Here it is before I tweaked it ...
The SOG scissors actually worked quite well in the PST frame, and didn't suffer as much from being "upside down" as they do in a SOG Powerlock frame. For those who weren't aware, they're kind of an outboard scissor configuration for inboard tools, which means the scissors lever goes the opposite direction to all other scissors. With the PST frame being so thin, this didn't matter so much when using the scissors, but when you weren't using the scissors they were a little too broad to fully stom into the handles. This meant that the tool never really closed properly.
I decided to switch these out for Fuse scissors, and found that actually created enough room to get an awl in there too. Here it is after the re-hash ...
Seems to be working out quite well. The drivers deploy slightly ... well .. overdeployed, by which I mean they go beyond stright with the body of the tool, but I don't find that a problem at all. In fact if you are just nipping up a loose screw, it can actually be a bit of a benefit. This tool originally came about because a while back I had an empty PST II frame after fitting all the innards into a PT-510 (which is now lost, or I believe may have actually been stolen from me at work), and so I fitted in whatever I had lying around go get it back carryable again. Overall I'm a lot happier with it like this than with the SOG scissors, and this actually gets a little more carry time than my original layout PST with pocket clip attached, mainly due to the scissors and serrated blade to accompany whatever plain edge knife I have on me at the time
Great tool you have there Fiddy.

-
Thanks

-
This is a very interesting thread. I had previously made my way through the first 18 pages, but now I have a tool to actually mod.
I'd like to do the following:
- Swap out the bottle opener for the micro bit holder
- Swap out the small screwdriver for a package opener (eg from the Wingman) (I hate those plastic packages!)
I know people have done the micro bit swap, but can I do it where the can opener is? Are they the same size? And finally, where can I get one?
For the second, can you move the package opener (or I suppose any tool) from the Wingman over? If not, do you know if there is a package opener that could be swapped into the Surge? And again, any idea where to get one?
I'm so excited! Thanks for any advice.
David
-
@drzeller said:
This is a very interesting thread. I had previously made my way through the first 18 pages, but now I have a tool to actually mod.I'd like to do the following:
- Swap out the bottle opener for the micro bit holder
- Swap out the small screwdriver for a package opener (eg from the Wingman) (I hate those plastic packages!)
I know people have done the micro bit swap, but can I do it where the can opener is? Are they the same size? And finally, where can I get one?
For the second, can you move the package opener (or I suppose any tool) from the Wingman over? If not, do you know if there is a package opener that could be swapped into the Surge? And again, any idea where to get one?
I'm so excited! Thanks for any advice.
David
Welcome to the forum drzeller.

The sm bit driver can go where the can opener or sm flat is with some minor work to clear the locking tab pivot, see pic.
The Wingman parts won't swap over well.
I would make a package opener out of the can opener or a flat driver.
Worth a mention is that the small bit can be used without the bit driver. -
I don't want to start a new topic.
Will a scissors fit in the can openers spot in my charge alx ???
-
???The blast scissors worked in an alx for me....
http://forum.multitool.org/index.php?action=dlattach;topic=51510.0;attach=132006;image -
Arrr

-
Yeah I don't want to grind anything.
It's fine the way it is I guess.
I don't want to lose any of my bit holders.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
