got in over my head, help me sweet baby jesus
-
Hi, welcome :D
So the washers you are trying to line up are copper color, right? Those do not go between the body and plier pivots. No washers there. Those four go between each blade/file and screw head. Sorry I cannot take a pic to show you at the moment, but hope it makes sense. Let us know when you got it man.
.For the benefit of newbies and me I think that needs a little clarification. There are copper washers between Rebar pliers and Rebar handles. Doesn't look as if there are any between Wave pliers and Wave handles.
So is it the handles or the pliers which require washers when swapping?

I leave the washers with the handles.
-
@JBW1 said:
Hi, welcome :D
So the washers you are trying to line up are copper color, right? Those do not go between the body and plier pivots. No washers there. Those four go between each blade/file and screw head. Sorry I cannot take a pic to show you at the moment, but hope it makes sense. Let us know when you got it man.
.IMO the washers on the Wave go between the handle and the tool, not the tool and the screw.
-
Thu process of elimination putting the copper washers, that came out of my wave on the plier side, at first between the pliers and body then to the the body and outside tools, then to the screw and outside tools, till it worked like original again.I had dropped it in some sand and hated the grinding sound, so i dismantled it and cleanned it up real good. Wasn't any kind of swap, but I feel your pain and frustration cus I was dealing with it last night :) good luck sir
-
@JBW1 said:
So no washers beween the pliers and body on a WAVE then, is what your sayn right?
When I put the washers between the body and blade, the liner lock hit the washer, maybe that's why you had to file yours down? But what got my wave back together was the washers between the tool and screw.This must be confusing for the OP. I'm no expert but I can see that my Rebar has a copper washer between handle and pliers and my Wave does not appear to have washers between the handle and pliers. My Rebar pliers have been temporarily removed but not my Wave pliers (I tried my Rebar pliers in a Fuse).
The Wave has copper washers between body and all external tools which does not impede the liner lock. If your Wave liner lock is hitting a washer then somehow you have ended up with an oversize washer.
Just guessing
but could it be a Rebar plier washer? zoidberg? -
JBW1, thanks for editing out that mess of quotes.
Lets try and clear this up some.
Rebar handles with Wave head. Has washers between the handles and head.
Wave handles with Rebar head. Has washers between the tools and handles.
I didn't file down the liner lock. It was the blade locking safety tabs. Now where is my coffee.
-
@zoidberg said:
JBW1, thanks for editing out that mess of quotes.Lets try and clear this up some.
Rebar handles with Wave head. Has washers between the handles and head.
Wave handles with Rebar head. Has washers between the tools and handles.
I didn't file down the liner lock. It was the blade locking safety tabs. Now where is my coffee.
It's OK to clarify but earlier you responded "I leave the washers with the handles". But that would be the Rebar handles. So I'm confused by the connection between "Rebar head" and tools. Not wrong but confusing.
-
@zoidberg said:
JBW1, thanks for editing out that mess of quotes.Lets try and clear this up some.
Rebar handles with Wave head. Has washers between the handles and head.
Wave handles with Rebar head. Has washers between the tools and handles.
I didn't file down the liner lock. It was the blade locking safety tabs. Now where is my coffee.
Haha yea I smurffed up that post,
Saftey locking tabs so that's what them little nubs are called :D
I guess we can all agree that it's easier to destroy than to create haha. -
JBW1, thanks for editing out that mess of quotes.
Lets try and clear this up some.
Rebar handles with Wave head. Has washers between the handles and head.
Wave handles with Rebar head. Has washers between the tools and handles.
I didn't file down the liner lock. It was the blade locking safety tabs. Now where is my coffee.
Haha yea I smurffed up that post,
Saftey locking tabs so that's what them little nubs are called :D
I guess we can all agree that it's easier to destroy than to create haha.Agreed. :)
-
JBW1, thanks for editing out that mess of quotes.
Lets try and clear this up some.
Rebar handles with Wave head. Has washers between the handles and head.
Wave handles with Rebar head. Has washers between the tools and handles.
I didn't file down the liner lock. It was the blade locking safety tabs. Now where is my coffee.
It's OK to clarify but earlier you responded "I leave the washers with the handles". But that would be the Rebar handles. So I'm confused by the connection between "Rebar head" and tools. Not wrong but confusing.
:D I only swap over the plier heads. All washers and tools stay in their respective places. Still with me? -
Thanks for the help with this guys, now I am more confused then before I clicked on this link.

I bet it is something I will have to see to understand and I got a couple of months before the swap happens so no worries.
-
Ok guys here's where I'm at,
I did what zoid recommended regarding the safety tab and dremeled it so it doesn't interfere with the blade. So now the rebar head is transplanted into the wave. I still have to remove some tools to allow the handles to close properly though. Currently the large flat head is grinding against the head when I try to close the handles. So I have to remove the large flat head. And probably the scissors which sucks because I really want the scissors.
The rebar body with wave head, I figured out why the posts would not snug up against the handle.. the posts were through the handle and plier head but was slightly off center and not lining up so when I tightened the screw it marred and bent the washers.. great.

-
@tinkering2much said:
Ok guys here's where I'm at,So now the rebar head is transplanted into the wave. I still have to remove some tools to allow the handles to close properly though. Currently the large flat head is grinding against the head when I try to close the handles. So I have to remove the large flat head. And probably the scissors which sucks because I really want the scissors.
Something doesn't sound right there. There is no need to do so on a Wave with Rebar head transplant. Are you sure you installed the tools in the bottom of the handle in the correct order as original?
Be aware the bottom Wave tools go in a specific order so they don't interfere with the pliers head when closed. Look at the pics of expanded un-modded Wave tool for reference.
-
I never changed the order of the tools on the wave, its still exactly the same as from leatherman all I've done is swap heads. I'm not sure why the plier head rubs the large flat head so bad but something has to change.
-
@tinkering2much said:
I never changed the order of the tools on the wave, its still exactly the same as from leatherman all I've done is swap heads. I'm not sure why the plier head rubs the large flat head so bad but something has to change.Try swapping the handles over. Make sure the fasteners are done up nice and firm. Normally it is the scissors and not the flat driver that makes contact. If you want to keep the scissors and have the handles close properly there are a few different ways to go about it.
With the Rebar handles and Wave head. Bent washers don't change anything. Just flatten them out as best you can, quick sanding if needed, put it together and tighten it up.
-
I'll flatten the washers and rub it between fine sand paper to polish.
If i open the large flat head and close the handles it closes just about perfect. Maybe this is a good thing the flat head is the problem rather than the scissors. I'm thinking I'll put the awl in the flat head spot and dremel the back of the awl to allow closure. Will that work?
-
@tinkering2much said:
If i open the large flat head and close the handles it closes just about perfect. Maybe this is a good thing the flat head is the problem rather than the scissors. I'm thinking I'll put the awl in the flat head spot and dremel the back of the awl to allow closure. Will that work?One thing to check is the Rebar pliers. I ended up with another pair sometime ago on which one side was thicker than the other, as if they forgot to re-fine its final shape in the factory. It may help to turn the pliers head around and install again. Just a thought.
It would definitely help too if you could post a photo of your Rebar pliers jaws.
Cheers.
-
one thing to mention -- I've noticed recently that there seems to be more variation in the Rebar plier heads than there was when the Rebar first came out. the first few mods I did, the scissors interfered with the Rebar plier head every single time, but all the other internal tools were fine.
the last couple mods that I've done have been more interesting. I actually had one that rubbed against the large flat driver as well, and another one that required me to reshape the can opener, of all things.

I'm not sure what the tolerances are on these plier heads. I'd be surprised if your scissors actually fit in there without any grinding/reshaping, but it's certainly possible that you got a plier head that plays nicely with the scissors.
-
This is rapidly becoming an excellent thread

Lots of great info coming out here guys, keep up the good work
-
@Breezy12 - there's something about that, for sure. I just briefly checked 4 of my Rebar pliers and the one from 2014 definitely isn't as needle-nose as the other 3 from 2012, it's slightly 'stumpier' for lack of a better word. But you really need to look for it, it's not something easy to notice even side-by-side.
Cheers.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
