Super DIY SAK Liner Cutter
-
You look like you've had a lot of practice at that mate

-
All I can say is bahahahahaha hahahhahahaha and
lol -
Ok guys, back to liner making. We left off last time with me hand cutting out a bunch of pieces, and each one had one punch mark on one side of each piece.
So after alot more cutting I ended up with 54 Al parts, and 24 brass.

Now for the drilling.. I mean lots of drilling, no really hours of drilling. (54 + 24) * 3 = 234 holes.
Ok, so each rough cut liner has the right side hole punched like so...

So I drill those out...

I end up with 78 parts with one hole drilled.

-
Here is the gear I use to drill the remaining 2 holes per liner.

Two broken carbide drill bits with tape for handles are my pins, and the drilling guide I made from simple 316 stainless, with very carefully located and drilled guide holes.
So to start, one guide pin goes through the guide and the single hole in the liner.


I visually line up the hole on the other end with the mark on the label paper underneath, and clamp the parts together with vice grips.

Now back to the drill press and the other end hole gets drilled.

And now I have both end holes drilled.

-
A second guide pin goes in the new hole and the vice grips are removed.

Next, you guessed it. The center hole is drilled.


And there we have it. One liner drilled with all three holes accurately located.

Now I just had to repeat this 77 more times to yield my 78 rough cut, but drilled liners.

That killed my wrists, so I will show the next steps tomorrow, which are fit up on the router pins, and routing to the exact profile.
I needed to make a bunch of Al liners up to go for red hard anodize, since I'm all out and people keep asking for black scales and red liners. :D
-
Thanks for documenting all this! It is fun to watch your progress and see all your skill and patience along the way.
Sent from my MB886 using Tapatalk 2
-
Thanks for the updates.
BTW did you get the mill you were talking in the birthday thread yet? Wouldn't it speed up the whole liner cutting process or would too much material go to waste? -
No mill yet. CNCing would be nice to cut the profiles for sure. I had the money saved up but I still didnt pull the trigger all they way yet...:D I think I still would cut up the pieces first for blanks then have the CNC go round a stack at a time to profile so that I dont waste as much material. But the easiest would be to have the CNC mill out the shapes from sheet stock with a 1/8 straight bit and leave some tabs. It would waste more material since Im making a 1/8 cut, but the speed might make that not matter so much.
-
No doubt, that is a LOT of holes to drill. :-\ Cheers for sharing mate.

-
A bump of my old liner making thread as a final followup.
I used to invest many many hours into doing these by hand, rough them out with a jewelers saw, drill them, stack them and use a router to shape, then hand finish....
Well it DID work, and its still worthwhile if you were only going to cut a few, but then again its just easier to sandwich a few between two stock liners and file awhile until you're happy. So I'd recommend that to anyone doing a few by hand. If you have a belt sander it speeds up the process alot as well.
Today for me though, it's just more efficient to waterjet them. Now that I know how to make the 2D CAD files, and now that I know the cut cost is about $3 each it's for sure the way to go. I still have to spend probably 15 minutes on each liner to do the edge finish and polish, but thats far less time than the old way. Live and learn. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login