One of the reasons I keep picking Gerber over Leatherman ...
-
You gave us very good points here. Good reading, thank you.
-
Great job ! I'm sure this will be very helpful for people

Maybe you could have the title of the thread Include "Comparisons of handle spread of various pliers in multi tools" so someone searching for this info could find it easier.
-
I had considered the Diesel way back when I was debating what Gerber MT to get for my second one. Now you're making me want to get one just to check it out >:D
-
This is a great overview

-
@parnass said:
Excellent series of posts, 50ft-trad. I concur with several points concerning the ease of using Gerber vs. non-Gerber pliers, but I think the majority of your analysis addresses gripping larger objects.For me, the Gerber MP400 and MP600 series don't do as well as the competition when gripping small objects. In that case, I find their handles are too close together. They are so close together that it's difficult to keep a finger in between, a technique I use to better control the gripping action of smaller objects. Perhaps spring loading the pliers would help there.
While most people sing the praises of the Leatherman Wave, the sharp top edges of the handles and tools chafe my palms when using the pliers. Plus, the knife spine can pinch my palm sometimes when using the pliers. I had the same chafing problem with the Surge (and it was just too big and heavy).
The Skeletool pliers has drawbacks, too. The asymmetric handles restrict you to holding them in only one position instead of two, and the curvature of the bottom handle forces my hand to slide towards the plier head.
I had a bad pinching experience with the original Gerber Multi Pliers several years ago. That led to using a long succession of Leatherman multitools with a few Victorinox and Shrades thrown in. More recently, I've acquired current versions of the Gerber MP400, MP600, and MP800 and have been pleasantly surprised in many respects.
My most comfortable multitool pliers at the moment are the Crescent ToolZall (aka/Bear Jaws), Super Bear Jaws, and Victorinox Spirit. The Gerber M600 blunt nose seems pretty good, too, but I've not had sufficient experience with it yet.
Just revisiting this post again, as I didn't pay it full attention before ...
The Skeletool is actually a tool which doesn't suffer from the handle splay as found on so many other Leatherman models. For me it is a tool which suffers a host of other problems instead. The concave handle is quite slim and there is very little spread of load across the fingers, which means the gripping force is focussed in a small area. I also find that my fingers end up uncomfortably scrunched together and instead of force being transmitted to the handle, most of it just coes into contorting your hand. The spiky lump on the convex side doesn't help matters either. It's a fantastic example of how NOT to design plier handles in my opinion.
You are right, the Ye Olde Mr Pinchy was another great example of "what not to do". I think the tool I sold to Gareth was in my posession for less than 15 minutes before I decided I had to get rid of it. What a nasty bitey vindictive piece of equipment. As soon as I picked it up it bit me, and then once I'd looked at the tools inside and closed it up, it bit me again ... and didn't stop biting me until I put the bloody thing down :ahhh Evil!
The original Bear Jaws tool I had was very good for comfort, but I ended up letting those go in favour of a more refined toolset. Whilst the handles were very comfortable, I just felt the tools were just a little too agricultural. They did the job, but it wasn't everyday user material when thre were so many other options that weren't as clunky.
As to sprung pliers, the Strata might be worth a try for you if you don't use your pliers too hard, but please do note my comments on the hollow plier head. I know Tom (Jerseydevil) is a big fan of the Strata and I believe it's one of his primary multitools. When he gets back he'll be able to give you a better insight than I can (the standard Strata is also very slightly different to the BG variant)
-
Thanks guys
I really appreciate the comments 
-
I do not own one to check with, but the OHT might be closer to the gerber when it comes to handle seperation. (since they basically used Gerber's design concepts)
I checked, you are right about that
Any chance you could offer up any comparison pics with one of the other tools that I have shown? Obviously your hands will be different to mine, but if there's a "like for like" shot with one of the tools I've covered, we should get a good enough idea of how it compares

-
@Grant Lamontagne said:
This is an amazingly well thought out post, and I tend to agree with you.SOG also is able to be used in the closed position, with the handles and head pointed the same way, but I feel the same way about it in that configuration- the handles just open too wide to be of much use.
Def
Sent from my smurfing hunk of techno sorcery
Thanks Grant

I agree on the "head inwards" configuration too. In fact that way, you might be able to get a bit of gripping force, but no leverage to turn/pull/twist or do anything with it.
Considering how bad the ergonomics are on the "Power" range of tools (particularly those with exposed "gears of madness", it's quite surprising how good the ergonomics were on some of their other tools. The Toolclip looks like it should be a bloody horrible tool to use, but is surprisingly comfortable and robust too. As for the Switchplier, that has got to be the best multitool EVER when used as a screwdriver. Mine has the bit adaptor (as you know ;)) and I don't think there's another multitool that I have owned that has come anywhere close to being as comfortable in "driver mode". It's just a humongous shame that the pliers are so flawed in their strength/integrity due to that pathetic little cast noggin taking all the load
-
@Syncop8r said:
I can better appreciate the shape of the Spirit/Swisstool (and normal pliers) now - to prevent hands slipping towards the plier heads. Spring loaded pliers would also help solve this.
I find the Skeletool usable both ways around but a spring would improve it a lot IMO.Are you going to compare with a Wave? I imagine it would be similar to the Surge which I find very comfortable.
As I mentioned earlier (reply #35) I just can't get on with the Skele at all. To me it needs the same corrective maintenance that Harley gave the Camillus/Less Proud tool ;) >:D But if other folks find it suits their hand, then that's all well and good

I'll dig out my Wave and see just how dismantled it is at the minute
I started looking at doing some more tweakification to it not long back, but I can't remember what state I left it in. From fairly recent memory, the grip is better than the Charge AL as it is slightly slimmer, but also not as angular.I do know from meeting up with the UK guys, that the Surge was in the realms of the ST300 for me, and could never be as efficient for me as the Wave. Trying to use it was a bit like wearing boots three sizes too big :P It did the job, but so many other tools would do the same thing a heck of a lot better
-
@parnass said:
Adjustable arc joint and slip joint pliers overcome the problem of having the handles too close or too far apart when gripping an item. That's why I often carry a Knipex Cobra pliers.Incorporating that into a reasonably sized multitool which also has a wire cutter would be interesting.
... and I'll dig out the Wichard tool too ... This has slipjoint, chrome plated, forged pliers ... and I'm pretty sure it has a small wire cutting area too. Unfortunately it's a bit limited with other tools. A flat driver/pry thing on the end of the plier handle, a semi serrated blade, and a can opener/caplifter
-
@av8r1 said:
This is my main complaint about the Wingman. The plier handles are wider open than the Wave's by a significant margin so the tool feels too big in the hands during use. That coupled with the spring action and the smooth steel grips means the tool slides backward in your hands during use. None of my other Leathermans seem to suffer that problem.I must express a dissenting opinion regarding small tools, though. Compare a Squirt to a Dime. The Squirt is a better tool by far. The pliers are much grippier, the wire cutters work, the blade holds an edge, and the bottle opener isn't anywhere near as obnoxious. Only thing I liked about the Dime better was the paint. The Squirt's anodized coating feels much easier to scratch off. They're about equal in scissors; I don't really like the leaf spring design. Maybe if it worked more like a Wingman in that spring tension is removed when the tool is closed, but meh.
I agree 100% with your comments on the Wingman. It's almost like they went out of their way to make that tool unwieldy. Assymetrical, heavily splayed, and uncomfortable pokey bits too.
Squirt vs Dime? Well, I agree the pliers are significantly better on the Squirt. For a start they don't have the weakness of the hollow head (like the MP700 and Strata mentioned earlier, but also the backsprings are much better supported. As regards the rest of the tool though, I personally prefer the Dime and consider it to be overall a better pocket tool (again ... for me).
Opinions generally seem to be split about 60/40 in favour of the Squirt I believe, but as this thread (hopefully) highlights, we don't all rate tools on the same sliding scale. I also still don't think it stands out as prominantly from the competition as the ST300, Surge or MUT do
-
Its funny as the only leathermans that hurt my hands are the ST/ST300 and the pst/pst2 and pulse,ive never felt that my old wave is that uncomfortable in plier position,oddly prefer it to the charge,i did find the mp800 comfortable if not a tad too chunky,
-
@Zed said:
Its funny as the only leathermans that hurt my hands are the ST/ST300 and the pst/pst2 and pulse,ive never felt that my old wave is that uncomfortable in plier position,oddly prefer it to the charge,i did find the mp800 comfortable if not a tad too chunky,It's been ages since I've had a go with an old style Wave. Do the handles sit differently to the new style?
-
@SteveC said:
Great job ! I'm sure this will be very helpful for people
Maybe you could have the title of the thread Include "Comparisons of handle spread of various pliers in multi tools" so someone searching for this info could find it easier.
I'm not sure how big a title can be :D Maybe the mods will suggest something if they feel it needs to be easy to search for .....
-
@50ft-trad said:
Adjustable arc joint and slip joint pliers overcome the problem of having the handles too close or too far apart when gripping an item. That's why I often carry a Knipex Cobra pliers.
Incorporating that into a reasonably sized multitool which also has a wire cutter would be interesting.
... and I'll dig out the Wichard tool too ... This has slipjoint, chrome plated, forged pliers ... and I'm pretty sure it has a small wire cutting area too. Unfortunately it's a bit limited with other tools. A flat driver/pry thing on the end of the plier handle, a semi serrated blade, and a can opener/caplifter
Schrade also used to make an MT with slipjoint pliers: the Schrade ST5 (and the Craftsman Professional 45471 re-labelled version). The pliers are reputed to be quite robust due to the laminated and overlapping construction of the jaws.
-
@50ft-trad said:
Adjustable arc joint and slip joint pliers overcome the problem of having the handles too close or too far apart when gripping an item. That's why I often carry a Knipex Cobra pliers.
Incorporating that into a reasonably sized multitool which also has a wire cutter would be interesting.
... and I'll dig out the Wichard tool too ... This has slipjoint, chrome plated, forged pliers ... and I'm pretty sure it has a small wire cutting area too. Unfortunately it's a bit limited with other tools. A flat driver/pry thing on the end of the plier handle, a semi serrated blade, and a can opener/caplifter
Schrade also used to make an MT with slipjoint pliers: the Schrade ST5 (and the Craftsman Professional 45471 re-labelled version). The pliers are reputed to be quite robust due to the laminated and overlapping construction of the jaws.
I never realised that tool had slipjoint pliers

Wasn't that one a hellish tool to try and use?
-
@50ft-trad said:
I had considered the Diesel way back when I was debating what Gerber MT to get for my second one. Now you're making me want to get one just to check it out >:D
I think I was trying to sway you when you were looking at the Flik (?)
but you wouldn't listen :PYeah you were ;) Maybe someday when I feel the need to buy another MT to try, I will get the Diesel. I think it will be at least one of the ones I consider anyway. I really don't think I have much need at this point to get anything else, unless there's something new someday that really appeals to me.
-
@50ft-trad said:
@50ft-trad said:
Adjustable arc joint and slip joint pliers overcome the problem of having the handles too close or too far apart when gripping an item. That's why I often carry a Knipex Cobra pliers.
Incorporating that into a reasonably sized multitool which also has a wire cutter would be interesting.
... and I'll dig out the Wichard tool too ... This has slipjoint, chrome plated, forged pliers ... and I'm pretty sure it has a small wire cutting area too. Unfortunately it's a bit limited with other tools. A flat driver/pry thing on the end of the plier handle, a semi serrated blade, and a can opener/caplifter
Schrade also used to make an MT with slipjoint pliers: **the Schrade ST5 (and the Craftsman Professional 45471 **re-labelled version). The pliers are reputed to be quite robust due to the laminated and overlapping construction of the jaws.
**I never realised that tool had slipjoint pliers

Wasn't that one a hellish tool to try and use?**
I haven't put mine to heavy usage as they are a bit rare these days, but I haven't noticed any particular issues. They are fairly large and heavy. If you can remember what specific problem there was I'll check it out on my examples.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
