My newest tool, the Mega Pry!
-
I had forgot that this was the site that I had a problem posting in before so I'll take care of that before I post anything else. Yes I posted my product here to advertise it, what better place than a multi tool forum? I'll get on the rights to sell/advertise and then I'll post updates.
-
@olaf_anderson said:
I had forgot that this was the site that I had a problem posting in before so I'll take care of that before I post anything else. Yes I posted my product here to advertise it, what better place than a multi tool forum? I'll get on the rights to sell/advertise and then I'll post updates.Good Call..

-
@olaf_anderson said:
I had forgot that this was the site that I had a problem posting in before so I'll take care of that before I post anything else. Yes I posted my product here to advertise it, what better place than a multi tool forum? I'll get on the rights to sell/advertise and then I'll post updates.Superb!

We'll look forward to the future updates

-
What if you just made a "notch" and a band that goes around the joining section?
Or maybe some dimples and ridges that allow them to be clicked together. Similar to a ratchet and socket.
-
@NKlamerus said:
Or maybe some dimples and ridges that allow them to be clicked together. Similar to a ratchet and socket.
It's called a ball detent, it will allow the user to hold the tool one handed in extended form instead of having to carry 2 seperate smaller pieces.
-
I really don't see why the 1/2 inch cutouts wouldn't hold. As long as it's a tight fit; the force of the user just pushes one end of the cutout against the frame of the other tool and should remain in place. I'm talking forces in a vertical or horizontal position, you start moving in ways that compromise the two joints I can see it not holding but up/down movements should be OK. I've seen tight tolerance when pieces fit together on some of my pocket knives and the fit between these two pieces would have to be at least that tight to work without fail.
-
@David Bowen said:
I really don't see why the 1/2 inch cutouts wouldn't hold. As long as it's a tight fit; the force of the user just pushes one end of the cutout against the frame of the other tool and should remain in place. I'm talking forces in a vertical or horizontal position, you start moving in ways that compromise the two joints I can see it not holding but up/down movements should be OK. I've seen tight tolerance when pieces fit together on some of my pocket knives and the fit between these two pieces would have to be at least that tight to work without fail.Isn't the same concept used to get more leverage with two wrenches?
-
Actually your right, the fit would be much better though.
Sent from my iPhone using Tapatalk
-
The only other take down / foldable crowbars ive seen, are that folding hammer/crowbar that was also a kickstarter project, an a military telescopic type pry tool.
I think you probably mean the groove in the handle improves strength to weight ratio, and not strength, as that is incorrect. Removing material doesnt make something stronger.
440C is not the best choice of steels for this type of tool, there are tougher/stronger steel choices. I wouldn't rank corrosion resistance on this type of tool very high as its not a blade.
The locking together isnt for strength but in general use, you dont want the thing to fall apart. If you can hold the tool vertical and it wont fall apart then thats fine, but then again a friction fit over time will fail. So some form of detent would be a great upgrade.
-
@Syph007 said:
The locking together isnt for strength but in general use, you dont want the thing to fall apart. If you can hold the tool vertical and it wont fall apart then thats fine, but then again a friction fit over time will fail. So some form of detent would be a great upgrade.+1
Yes, holding vertical wouldn't be an issue as is, but you couldn't use it sideways or upside down without a detent. -
Man... I gotta say, I've been looking at this thread since it's revival, and I think this might be a winning design, detents or not. Sure, it won't be as strong/reliable as a solid crowbar, but it should offer a LOT more leverage than a single piece of the tool alone. And the small storage profile is awesome.
As with multitools, it has its limits, but for the space savings, I think it's worth the limitations. By space savings, I suppose I mean that limiting the length dimension, even if doubling the thickness when stored, is an improvement.
I don't know anything about metallurgy, but it seems a spring steel would be best for this? Or if you could make it out of brass, it might be more useful in rescue situations (so it wouldn't spark and potentially ignite gas leaks and such).
Then, duracoat it Plain Brown Earth and slap the word 'Tactical' on it, and it'd be a huge seller. :D
-
I kind of look at this tool the same way I look at using two wrenches together for extra leverage. It works, and you don't have one big tool to have to store. I like the idea of this quite abit.
I also think that the pressure fit should suffice, and not really hinder its use. -
@Lynn LeFey said:
I don't know anything about metallurgy, but it seems a spring steel would be best for this? Or if you could make it out of brass, it might be more useful in rescue situations (so it wouldn't spark and potentially ignite gas leaks and such).The best attribute to consider for a steel for this purpose would be what is normally referred to as 'toughness'. A good medium carbon steel with high toughness is the best choice.
This was the other kickstarter one I found, if you havent seen it.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login