charge lanyard ring - silly?
-
I'm with the other guys! Remove the fixed lanyard ring, that's what I did with my wave and it works great. What this does is allow you to attach the pocket clip on either side so you can have your preferred blade ready for quick deployment straight out of the pocket, if you know what I mean. Using the standard pocket clip location in a right pocket it lends towards the plain edge blade being first preference, without flipping the tool over. Removing the fixed lanyard ring allows you to put your pocket clip there so the serrated blade is first preference out of the pocket for an emergency situation, eg. cutting your way out of a seatbelt in a flipped car leaking petrol onto you... Anybody else done this??
-
@danilo said:
OK,
thank you all for the suggestions!I hadn't thought about replacing the fixed ring with the removable one (although it will present the same problem, except you can detach it to deploy the tool next to it, either the scissors or the bit holder).
Since the charge is quite new, I'm not into modding it as of yet, so I'll try some other ways before removing the fixed ring, or drilling the clip (this one would be a soft mod, as the clip is easily replaceable, but I see there isn't much space in there anyway...)
Anyway I was thinking that maybe some flat paracords, which I've seen in some videos, maybe they'll fit in there without mods? Has anyone tried them out?
Danilo
Well from what i tried gutted paracord doesn't work quite well.
I also have a quite new charge that im not afraid to mod because it is just taking a simple piece off.
I recommend storing the lanyard ring that you don't use where you'd put the clip or ring when not in use
Sent from my iPhone using Tapatalk
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
-
@danilo said:
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps. -
You will need T-10 security bit. not the normal ones.
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps.oh I see, and I've read something about it before now that you say that...
thanks for the info, but how can I heat it up? with just a cigarette lighter?
p.s. I've mistakenly reported your message as spam while trying to quote it... darn Tapatalk... sorry
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps.oh I see, and I've read something about it before now that you say that...
thanks for the info, but how can I heat it up? with just a cigarette lighter?
p.s. I've mistakenly reported your message as spam while trying to quote it... darn Tapatalk... sorry
Yeah a lighter works fine. No stress re the spam report mate. :)
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps.oh I see, and I've read something about it before now that you say that...
thanks for the info, but how can I heat it up? with just a cigarette lighter?
p.s. I've mistakenly reported your message as spam while trying to quote it... darn Tapatalk... sorry
Yeah a lighter works fine. No stress re the spam report mate. :)
Yup, the bottom, inside tools pivot pin is D shaped so one screwdriver should be enough. I'm just not sure which side is the actual screw. :P
If you ever decide you need to tighten or unscrew the plier pivots, then you'll need two screwdrivers.
-
ah the other side isn't d-shaped, nice to know.
but I also understand tightening the pliers end screws doesn't make the plier head tighter, I can't remember the thread I l've read it in, but someone said it just acts on the external tools tension (blades, file and saw)
nice to know anyway, thanks
-
Correct.

-
A 15mm split ring will do the trick:
Simply slide it on clip, once clip in place the split ring won't fall out.
Tool can be pull out quickly with index finger.
The ring is small enough not to interfere the usage of any implement.
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps.oh I see, and I've read something about it before now that you say that...
thanks for the info, but how can I heat it up? with just a cigarette lighter?
p.s. I've mistakenly reported your message as spam while trying to quote it... darn Tapatalk... sorry
Standard response to Zoidberg posts right there.^
-
oh! you just made me realize I can unscrew the handle and remove the ring without cutting out anything.
I'm in for a reversible mod like that !
And thanks for the tip on how to not lose the small part :)ok, so in the end I now need two t10s, I knew I was ending up buying something, I just needed to focus on what

Danilo
Unless they changed them like with the Surge you'll only need one t10 as the post is keyed and does not rotate.
The screw is on the pocket clip and lanyard sides of the handle. Heat the screw to break the loctite. Hope that helps.oh I see, and I've read something about it before now that you say that...
thanks for the info, but how can I heat it up? with just a cigarette lighter?
p.s. I've mistakenly reported your message as spam while trying to quote it... darn Tapatalk... sorry
Standard response to Zoidberg posts right there.^
Exactly. :D
-
My solution to an issue I didn't even bother to resolve until now.
</post/1034292> -
lol,
it is also a nice idea, and one can attach the lanyard to the ring and fix my problem as well, I'll try it out! -
I am not a fan of lanyards, but do what you gotta do.

-
Btw, if you got money, you can get a full set of bits and use only one t10. It worked for me!
Sent from my iPhone using Tapatalk
-
in the end, I've bought the security torx (in a kit with other bits, as if I didn't have enough already...) and removed the fixed ring and inserted the removable one.
the morning after I reassembled the way it was: the removable ring is too tall! I can't even close the sheath button with it!at least now I like a bit more the fixed ring... I got used to it, and the even when using the scissors is not a big deal anymore...
-
At least you gave it a shot mate!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
