KPT (Kampfer's Pocket Tool)
-
It is tension bar to hold bit in place.
-
@MadPlumbarian said:
Interesting, what's the open channel going passed the hex?
JRProbably a spring, to hold the bit in place.
I like it
, except for the box-opener. I prefer to have no pointy edges so I can really just dump it into my pockets... Oh, and you are missing a pocket clip :P -
I dont like the box opener, people carry this tool would EDC a knife anyway.
-
Box opener = pocket ripper
-
I'm not much of a one piece tool fan, but to play along... any reason the upper part of the aligator wrench can't be a Phillips? As the centre line would be skewed to the rest of the tool, the flat driver shouldn't be an obstacle
-
I like it
nice one Kampfer.
-
Revised
-
I think all meant to have the Pillips in the line of the wrench, so you hold the KPT at an angle when using and thereby the flat screwdriver does not get into the way.
Btw. I would keep the evolution pictures for reference.
-
@Etherealicer said:
I think Al meant to have the Pillips in the line of the wrench, so you hold the KPT at an angle when using and thereby the flat screwdriver does not get into the way.Btw. I would keep the evolution pictures for reference.
Yup.
DEFINITELY keeping the evolution pictures should be.

Otherwise the discussion looses it's meaning.

-
@Etherealicer said:
I think all meant to have the Pillips in the line of the wrench, so you hold the KPT at an angle when using and thereby the flat screwdriver does not get into the way.Btw. I would keep the evolution pictures for reference.
Yea, that was the intend
-
@Etherealicer said:
I think all meant to have the Pillips in the line of the wrench, so you hold the KPT at an angle when using and thereby the flat screwdriver does not get into the way.Btw. I would keep the evolution pictures for reference.
Sorry if I wasn't clear, Etherealicer. I meant in-line/symetrical to the remaining material so thehead is formed evenly. So if the wrench formed an angle of 30 degrees, the centreline of the driver would be at 15 degrees
-
Drivers revised.

-
I think we all meant the same :D
How about making on side of the scraper / pry-bar round (I kinda like the round side from my pocket-wrench, lots of applications)
-
Hard to please you guys.

-
Was more thinking about an asymetrical design


-
Like it.

-
Not bad for a first draft.
The outward pointing screwdrivers are asking for trouble though, I'd make them parallel to the tool sides, but made one a tiny bit shorter than the other so they're not in a way. I feel 'pain' just by looking at them ;)
That's however easier said than done, because the shorter screwdriver end will always "suffer" as the longer bit will be in the way.As for the scraper/pry bar ends, I'd make them asymmetrical similar to what you did in your last photo but ensure the shorter pry tongue is finished in a way to be used as a large flat head screwdriver, so a little thicker than the other pry tongue.
For the bit tension bar....this could be designed in a way to double up as a pocket clip too. You could also add knurling or jimping on the inside of the bar.
Just some of my thoughts...that's all. Keep the dream going!

-
I personally don't drivers at the ends of wrench.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
