Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Common "Flicky-Plier" Problem?

Scheduled Pinned Locked Moved Gerber Tools
19 Posts 1 Posters 2.6k Views
  1. Home
  2. Tool Talk
  3. Gerber Tools
  4. Common "Flicky-Plier" Problem?
Common "Flicky-Plier" Problem?
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ducttapetech Offline
    ducttapetech
    Posts: 18,707
    ducttapetech Offline
    ducttapetech
    wrote on last edited by
    #7 Quote Reply

      I had a MP 600 do this to me. Never did really figure out what it was. Over time it did correct itself. I think it might have been a burr in the pivot itself.

      Nate

      1 Reply Last reply
      • gregozedobe Offline
        gregozedobe
        Posts: 5,148
        gregozedobe Offline
        gregozedobe
        wrote on last edited by
        #8 Quote Reply

          I have a vague recollection of someone here on MTo describing the same problem with a LM tool. Couldt be either a bit of grit/gunge inside the plier pivot or a slight deformation that binds after harder squeezing on the handles to grip something tightly. Unfortunately there is no non-destructive way to investigate problems inside peened plier pivots.

          1 Reply Last reply
          • lowtech Offline
            lowtech
            Posts: 4,799
            lowtech Offline
            lowtech
            wrote on last edited by
            #9 Quote Reply

              @ducttapetech said:
              I had a MP 600 do this to me. Never did really figure out what it was. Over time it did correct itself. I think it might have been a burr in the pivot itself.

              Nate

              I did experience this on a MP 600, too. My EDC MP 600 did not ever do it, no matter how hard I use it. I believe it might be a comnbination of the axis of the plier head and plier handle not being congruent and the plier head being a bit stiff, I have no real explanation, just wanted to emntion I experienced that ,too.

              1 Reply Last reply
              • rdub934 Offline
                rdub934
                Posts: 1,991
                rdub934 Offline
                rdub934
                wrote on last edited by
                #10 Quote Reply

                  Thanks for the input, folks. I think I agree lowtech, maybe since most Gerbers are "rattly" they are more prone to this sort of malfunction since the pliers are able to be at slightly different angle than the handles. I never really saw the looseness of Gerbers being a real problem just a personal preference type of deal, but maybe this is one reason in favor of tighter tolerances as found on Leathermans.

                  I wonder if this is as common of a problem on the tools from other companies?

                  1 Reply Last reply
                  • Dunc Offline
                    Dunc
                    Admin Team
                    Posts: 11,308
                    Dunc Offline
                    Dunc
                    Admin Team
                    wrote on last edited by
                    #11 Quote Reply

                      I've had a fair few MP400's and I've seen this problem on one of them. It seemed to be caused by the pivot. After gripping down hard on something with the pliers a certain percentage of the opening of the jaws was stiff. Continuis open and closing returned the pliers to normal feel until you gripped something tight again.

                      1 Reply Last reply
                      • tattoosteve99 Offline
                        tattoosteve99
                        Posts: 6,326
                        tattoosteve99 Offline
                        tattoosteve99
                        wrote on last edited by
                        #12 Quote Reply

                          Take a regular graphite pencil and rub over the pivot area. Apply some oil or whatever. Do this a couple times and work it in good. Should work

                          1 Reply Last reply
                          • PTRSAK Offline
                            PTRSAK
                            Posts: 4,776
                            PTRSAK Offline
                            PTRSAK
                            wrote on last edited by
                            #13 Quote Reply

                              My MP400 has this problem, I first thought of a burr on the wire cutters but upon examination there is none but that's how it feels. after that first movement the pliers move freely.
                              Most annoying.

                              1 Reply Last reply
                              • neillcurrie Offline
                                neillcurrie
                                Posts: 860
                                neillcurrie Offline
                                neillcurrie
                                wrote on last edited by
                                #14 Quote Reply

                                  I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                  Though there was no apparent damage to either wire cutter, I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                  End of problem in my case.
                                  BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                  1 Reply Last reply
                                  • David Offline
                                    David
                                    Posts: 9,246
                                    David Offline
                                    David
                                    wrote on last edited by
                                    #15 Quote Reply

                                      As others I've had this problem on the MP600 after hard gripping.

                                      @neillcurrie said:
                                      I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                      Though there was no apparent damage to either wire cutter, **I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                      End of problem in my case.**BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                      Thanks for the tip. :tu:

                                      1 Reply Last reply
                                      • rdub934 Offline
                                        rdub934
                                        Posts: 1,991
                                        rdub934 Offline
                                        rdub934
                                        wrote on last edited by
                                        #16 Quote Reply

                                          I definitely do not have any burs, nicks, or dents in my cutters - the Octane is anvil-style cutters so even if they were damaged, it would not be causing this issue. Strangely, I have discovered that my MP400 seems to be mostly good to go these days. Only about 1 in 20 times that I deploy the pliers do they exhibit any stickiness. The Octane is still sticky basically all the time, but it is not as bad as it had been - the pliers are much more usable now than they were previously.

                                          1 Reply Last reply
                                          • Freaver Offline
                                            Freaver
                                            Posts: 629
                                            Freaver Offline
                                            Freaver
                                            wrote on last edited by
                                            #17 Quote Reply

                                              @David said:
                                              As others I've had this problem on the MP600 after hard gripping.

                                              @neillcurrie said:

                                              I had it happen with a MP600. I looked at it carefully to see where in the arc of closing the pliers it happened, and it was just when the wire cutter faces moved across each other.
                                              Though there was no apparent damage to either wire cutter, **I carefully flattened the faces with a diamond flat rod, until they just passed cleanly.
                                              End of problem in my case.**BTW, you can buy small tubes of graphite almost any place that cuts keys. I've never actually used mine, but it's supposed to be a good dry lubricant, that doesn't hold onto pocket lint, etc.

                                              Thanks for the tip. :tu:

                                              +1. Except I've had this problem since I got my MP600 secondhand - it was in a not too pretty state, so the previous owner might have been a bit rough on it. Gotta try that trick with a diamond rod or file, when I get the chance.

                                              1 Reply Last reply
                                              • Cupboard Offline
                                                Cupboard
                                                Posts: 2,018
                                                Cupboard Offline
                                                Cupboard
                                                wrote on last edited by
                                                #18 Quote Reply

                                                  @gregozedobe said:
                                                  I have a vague recollection of someone here on MTo describing the same problem with a LM tool. Couldt be either a bit of grit/gunge inside the plier pivot or a slight deformation that binds after harder squeezing on the handles to grip something tightly. Unfortunately there is no non-destructive way to investigate problems inside peened plier pivots.

                                                  Yes, it's a known problem on the Rebar, particularly when fairly new.
                                                  I had one develop it after about a month of use, but then it cleared after about 6 months. You'd apply a lot of force to it then the pivot would seize up.

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. Tool Talk
                                                  3. Gerber Tools
                                                  4. Common "Flicky-Plier" Problem?
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0