wing man scissors on wave
-
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
) -
@pingu said:
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
)I don't recall changing the spring piece at all. And yeah that is probably what Zach has done.
@Zachbradley said:
No i have not. Do you mean the holes that the screw goes through? If so, how will this help? (Im not trying to be rude, in just puzzled :P)Yes, the hole that the screw goes through has to be large enough to let the post pass through.
The post (not the screw) is what the scissors and spring pivot on.
You may have to file the back of the scissors piece (not the spring piece) so that the liner lock engages.
Tighten the screw all the way so that the spring piece can't be pushed off the post.
File a little and check the fit, rinse and repeat, don't rush it. -
...rinse and repeat...
rinse? What are you doing to the mother country's language

Anyway damn this thread
. It has rekindled my interest in having Wingman scissors in a Wave, or my case my Ve. Also another go at at a single handled Wingman. I do not think I can resist 
I'm smurfing it to death just like
you and those scissorseveryone else does around here. :P -
Yes it was me who broke my Wingman scissors tang while attempting to drill it
instead of using the diamond burr as usual.But I have a question while the experts are on. I note the spring arm is already oversize at a tad under 6mm. Assuming I hadn't smeg'd the first stage does the original clearance between spring arm and post have to be restored?
(I'm guessing Zach must have the scissors piece trapped between post and screw against the liner lock
)I don't recall changing the spring piece at all. And yeah that is probably what Zach has done.
I've done this mod enough times now to say with certainty that the spring piece does not require any modification. :)
-
please pardon my newbiness. I am still not sure how to make this work. Here is how the scissors right now are acting: when locked into place, the scissors are not tight, so they dont spring back up. but when i force them down with my finger and hold it like that, they work like they should. but thats only when i am holding the scissors down with the opposite hand that i am using to press down the thumb pad. Can someone that has done this before please upload some picks showing me what i need to do? I would really appreciate it!
-
No i have not. Do you mean the holes that the screw goes through? If so, how will this help? (Im not trying to be rude, in just puzzled :P)
Yes, the hole that the screw goes through has to be large enough to let the post pass through.
The post (not the screw) is what the scissors and spring pivot on.
You may have to file the back of the scissors piece (not the spring piece) so that the liner lock engages.
Tighten the screw all the way so that the spring piece can't be pushed off the post.
File a little and check the fit, rinse and repeat, don't rush it.Did you read this? How much of it do you understand? Enlarged the pivot hole yet?
-
@Zachbradley said:
please pardon my newbiness. I am still not sure how to make this work. Here is how the scissors right now are acting: when locked into place, the scissors are not tight, so they dont spring back up. but when i force them down with my finger and hold it like that, they work like they should. but thats only when i am holding the scissors down with the opposite hand that i am using to press down the thumb pad. Can someone that has done this before please upload some picks showing me what i need to do? I would really appreciate it!I have some pics that might help, but they're on my home computer. (I'm still at work.) I'll try to post some this weekend.
-
I would appreciate it
-
ok, I found a couple pics from a recent mod that I did for someone else that might help.
most of the time, all I need to do with the Wingman scissors is enlarge the pivot hole as previously discussed, but sometimes the back of the scissors piece doesn't line up well with the liner lock, the scissors won't work properly, and it looks like this:

if that's the case, then you just need to slowly file it down, stopping to do frequent test fits, until you get a nice flush lockup like this:

does this help?

-
thank you for the photos. i think i have just the opposite problem that you had. on yours, the scissors needed to be filed down because there was too much for the lock to activate. on mine, the lock activates but there is nothing to file down, there is actually some wiggle room there.
-
@Zachbradley said:
thank you for the photos. i think i have just the opposite problem that you had. on yours, the scissors needed to be filed down because there was too much for the lock to activate. on mine, the lock activates but there is nothing to file down, there is actually some wiggle room there.interesting... I've never seen that before. could you try to get some close-up pics so we can see what you're talking about?
-
@Zachbradley said:
on mine, the lock activates but there is nothing to file down, there is actually some wiggle room there.In the spirit that this is a knowledge base for others could the hole enlargement (how exactly did you enlarge the hole?) have been a little off-centre

I've seen Amazon reviews complaining that Wingman scissors didn't spring but it turns out the lock wasn't engaged. I suspect or fear there are some tight tolerances required for correct operation.
Hope that you can recover something.
-
I finally got it figured out! thanks for the help, you guys!
-
@Zachbradley said:
I finally got it figured out! thanks for the help, you guys!glad to hear it!
what turned out to be the problem?? -
Just needed to make the pivot hole larger and file off the back of the scissors. Basically what you guys were telling me
-
more pics please

-

Sent from my iPhone using Tapatalk
-
Beautiful!
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login