Leatherman plier friction problems?
-
I find it strange that the cheapest leatherman (wingman sidekick) has the best plier locking system?
Do you mean locking open or locking closed and what exactly do you mean by "locking"?
The sidekick has springs that lock in a notch on the plier, thereby it locks firmly and for years to come in the closed and open position.
other leatherman's just have the friction on the bolts and the middle edge of the plier that is pushed against the handle top.That reminds me of my Kick (rip) which had open friction via the slightly eccentric pivot against the handle as you describe. Was unacceptably stiff. My Fuse has exactly the same system but is not over stiff. Closed retention is just pivot to Zytel friction and easily adjusted.
You are right to highlight Wingman (spring against pivot flat in open and closed position). Seems to work well with every expectation of lasting. Speculating that Wingman needs good closed retention because of the sprung pliers.
Rebar has closed retention via two spring arms against pivot flats. Same as Wingman. If that fails that has to be a warranty issue. Opening friction is the spring arms against the pivot and handle friction set by pivot torque. Adjust to suit. The fully open retention is the old eccentric pivot against the handle. I could see that wearing with heavy use. Probably a warranty issue.
Warranty is not an option for me because invariably my MTs are modded. I would attempt adjustment.
-
@anditsgone said:
I have loosen al the bolts on my wave because they where too tight, it is pretty difficult find the right tension, half a turn too lose and the tools just fall out, half a turn too tight and your nail breaks.Yes half a turn is too much. I use low strength thread lock and adjust a few degrees at a time.
-
There is another method that requires a hammer, nail punch and screwdriver.
I'll try and get some pics for you later showing where to do the adjusting work.
Ten points awarded if you can figure it out before I find time to take the pics.
-
-
@zoidberg said:
There is another method that requires a hammer, nail punch and screwdriver.I'll try and get some pics for you later showing where to do the adjusting work.
Ten points awarded if you can figure it out before I find time to take the pics.
I suspect you are going to solve a too loose when closed up issue. Regarding my Kick (rip) stiff to fully open issue would you have recommended filing the pivot or the handle?
-
There is another method that requires a hammer, nail punch and screwdriver.
I'll try and get some pics for you later showing where to do the adjusting work.
Ten points awarded if you can figure it out before I find time to take the pics.
I suspect you are going to solve a too loose when closed up issue. Regarding my Kick (rip) stiff to fully open issue would you have recommended filing the pivot or the handle?
I was going to cover both.
In the past I've tried the pliers cam/wedge and the handle.
I find the nail punch and screwdriver much quicker and it can be adjusted both ways.
-

OK I realise I need a NZ clock on my desktop.
Added it and its smaller than the mother country clock

-

Didn't mean to wake you up. No hurry for my question, Fuse handle stiffness is OK. -
Today i used a blast from a friend of mine, the tool is 5 years old.
The plier friction in the open position is good, but closed is completely worn out.
If you hold the tool with one hand the other handle just falls out. -
@anditsgone said:
Today i used a blast from a friend of mine, the tool is 5 years old.
The plier friction in the open position is good, but closed is completely worn out.
If you hold the tool with one hand the other handle just falls out.Blast closed friction is 100% pivot to Zytel. Nip up the pivot.
-
Today i used a blast from a friend of mine, the tool is 5 years old.
The plier friction in the open position is good, but closed is completely worn out.
If you hold the tool with one hand the other handle just falls out.Blast closed friction is 100% pivot to Zytel. Nip up the pivot.
Is the plier pressing against the zytel insert?
That would mean that it weares out in a couple of weeks. -
Today i used a blast from a friend of mine, the tool is 5 years old.
The plier friction in the open position is good, but closed is completely worn out.
If you hold the tool with one hand the other handle just falls out.Blast closed friction is 100% pivot to Zytel. Nip up the pivot.
Is the plier pressing against the zytel insert?
That would mean that it weares out in a couple of weeks.There may or may not be a washer but that's the principle. I don't think a couple of weeks is right.
-
-
-
-
-
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






