ReCharge
-
Dissembling the Charge was even easier thanks to the Safety T-10.
Re-assembly was a bit tricky, took some practice. Decided to exchange couple of the inner tools
Dropped the Mini-Bit-Holder and the scissors and shorted the flat-driver who now sits in the middle. Added the long small-screwdriver and the awl.
ReCharge
Unfortunately, the tool does not close nicely, so I will have to work on the awl and the small screwdriver. The shortened flat, also requires some work.good idea moving the large driver.
what will you do without the scissors? Very nice jobScissors: I didn't really like those tiny scissors attached to such a big tool. So carry Vic 58mm will give me better scissors, that are more convenient to use. Or I replace one of the blades with larger scissors.
I think ultimately at least one of the blades has to go, probably the PE, as I carry a PE folder.
What would you replace it with?
Maybe scissors or a pry-bar. I'm also studying Metros mods, so maybe a utility blade. However, first I have to do the internal tools, then I see what my options are.
I also have to consider my limited capabilities. I might dream big, but whether I can pull it off is in the stars. ::) -
Nice work (but I'd never give up scissors).
Where'd you get the elbow socket? Part or SKU number? It's just the right size as a companion.
-
-
Did put some work into my ReCharge... largest problem was not the awl, but the long small flat... now it closes up tightly again. I also fiddled with the two main blades and they are now opening smooth again.
Because I could not think of what I would like to do with the middle flat, I put the small-bit-holder back in. Ultimately this has to go, but first I need a better idea, as a pry tool does not work in the middle slot.
-
Could you live with a shorter small flat in the middle?
Or if I can find a spare here, I could hack (get the kid to grind) the back end and you wouldn't lose any reach.
-
@zoidberg said:
Could you live with a shorter small flat in the middle?Or if I can find a spare here, I could hack (get the kid to grind) the back end and you wouldn't lose any reach.
I have a bit holder, don't really see the point of another stubby flat driver. Its middle position and stubby nature makes it awkward to use as pry tool or chisel (that was my first thought).
The long small driver can be used for other things AND has reach. I was thinking of transforming the wide flat, into a hook but I'm uncertain about its utility.
Now I'm considering to drop the long small flat and the eye-glass screwdriver for an extra thick (especially at the pivot) prying tool. Because that is what my ReCharge really misses. -
Could you live with a shorter small flat in the middle?
Or if I can find a spare here, I could hack (get the kid to grind) the back end and you wouldn't lose any reach.
I have a bit holder, don't really see the point of another stubby flat driver. Its middle position and stubby nature makes it awkward to use as pry tool or chisel (that was my first thought).
The long small driver can be used for other things AND has reach. I was thinking of transforming the wide flat, into a hook but I'm uncertain about its utility.
Now I'm considering to drop the long small flat and the eye-glass screwdriver for an extra thick (especially at the pivot) prying tool. Because that is what my ReCharge really misses.Putting the small flat in the middle and hackin it to keep the reach would mean you could put a full length large flat against the side for a pry tool.
Do you have a Rebar phillips to make a thick based pry tool?
That would be pretty sweet. 8)
-
Do you have a Rebar phillips to make a thick based pry tool?
That would be pretty sweet. 8)
That should be strong at the pivot but how does the material strength compare when the nose is thinned down enough to pry

I don't know. Not sure if it's been done before. I'm sure it would be fine for normal use.
-
I took a good look at the Philips-driver last night. I think its too thin for a general purpose pry-tool. It might be great for other purposes.
I have a question are the small tools from Surge/ST300 compatible with the Charge frame?
This might seem a bit odd, but this project makes me appreciate the complexity of designing a MT.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


