Emerson Multitasker EDC-2
-
@lanedecamp said:
Multitasker and Emerson made the decision not to include pliers, which in turn made the tool much smaller and made it possible to make it much faster to pull out and use.Basic idea? Most of the time what you need -- really need -- isn't scissors or odd screwdriver bits or specialty saws or whatever. You basically just need to cut, to dig a hole you can put a screw into, and then to screw the fastener in.
I suspect more than a few people might feel the need for pliers to grip, pull, loosen/ tighten nuts/bolts, or cut wire, but if you're happy without pliers I'm not going to say your opinion is wrong - for you
That last rider is very important, as what suits you perfectly may have shortcomings for someone else. It's good to have a choice, so every one can choose what suits their individual needs best.
-
I am not sure where you see the benefit of the Multitasker-2 over a SI SAK or the new 111mm Soldier?
They deliver blade, screwdrivers, awl in a much lighter and cheaper version. Plus you don't have to worry about corrosion! ;)This EDC-2 has a locking awl which is important if you don't want it to fold up on you when you bear down on it such as when making a belt hole in tough leather. This happened to me yesterday with a SAK awl that didn't lock.
-
@lanedecamp said:
I've been testing one for the last several weeks, including sharing it with local fire department, local search and rescue, and at this moment with some folks at SOCOM in Florida. We've been comparing it to the Multitasker 3, plus a whole variety of the usual multitools, rescue tools, etc.This was designed in partnership with Emerson, and shows the heritage. The focus is on ease of use, almost to the instinctual level. You have to think when digging into a Charge TTi, but with this one, you have just the key basic tools that make or break a situation.......................All the tools from Multitasker are made without regard to cost -- they go for the best materials and best manufacturing techniques, and you pay for those. But I know I'll never see one break.
Well, lanedecamp, I want to thank you for taking the time to write your review. I am somewhat surprised that so many readers seem negatively disposed to both the tool, and also critical of your review.
Remember that your opinions remain just that, as do theirs. However, at least you have used the tool seemingly quite extensively, whereas the critics seem to be pontificating from a position of zero everyday-for-them experience. That speaks volumes.
As for the somewhat typical knee-jerk "this thread is useless without pictures" response, there's google, and it's easy to use. Brings up far more pics than anyone needs in less than a second. -
i would not consider the can opener on Pioneer as a + driver.
-
I agree that the most important point is if a tool works for you in the situation you are in.
Apart from that part of the discussion, does anyone own a Multitasker EDC/EDC 2 and can show some comparison pics with some of the usual suspects? (93 mm SAK, 111 mm, Wave...)?I can imagine the quality is good, my brother owns some Emerson fixed blades that are made very well.
-
I wish a few things were different on the tool, but am definitely drawn to it and would carry one. I wish the steel choice was better. I would be good with 154cm. I'm alright with the 440c, but not at the price point. If this was a $50 knife I would not mind the 440 at all. I hate the blade shape. Just personal preference. I like the tool selection and the reach in the drivers. I also like the locking half stop. If I could find one for a decent price I would definitely give it a go.
-
I like the idea of this tool, but can never warm up to the recurve of a short blade(I know it's Emerson, but still...)
I think the 'hurdle' of this product is probably pricing. When compared to most similar Vic or Wenger products, it has the advantage of locking tools and better scales. But whether those extra features and the brand are worthy of almost two Swisschamp, that will largely depends on the buyer.
-
I'm probably one of the few people who doesn't mind the bladeshape at all. But the price point is very off putting
-
@captain spaulding said:
i would not consider the can opener on Pioneer as a + driver.
I would. I mean its not a proper phillips and if you have the screw recessed or in any sort of hole it probably wont reach, but it definitely works on phillips.
Cap, why you always lock horns with me, hum...?

Just agree with me so I can sleep better, please. :D -
@captain spaulding said:
i would not consider the can opener on Pioneer as a + driver.
I would. I mean its not a proper phillips and if you have the screw recessed or in any sort of hole it probably wont reach, but it definitely works on phillips.
Cap, why you always lock horns with me, hum...?

Just agree with me so I can sleep better, please. :D:D :D
I can't agree, but I hear tea before bed helps with that sleep.
:P -
I will say technically its not a phillips though since it actually only turns the screw with a flat head....... Good enough.
:D :D -
@captain spaulding said:
i would not consider the can opener on Pioneer as a + driver.
I would. I mean its not a proper phillips and if you have the screw recessed or in any sort of hole it probably wont reach, but it definitely works on phillips.
Good to know in a pinch.
All of us who are waiting until it's cheaper are really saying we are waiting until they license the design to Kershaw and start making it in China.
I just bought such an Emerson/Kershaw knife, the CQC-7K 6034T at like a third the cost of the pureblood Emerson it was derived from. I like my E/K better, it has a more ergonomic handle. I wasn't looking for it but it's one of those knives that once you hold it in your hand in the store you know you are going to buy it. The blade is sort of a hybrid tanto/bowie that just gets it right.
I like having both the disc and wave pocket hook opener options, another refinement of the Chinese variant. It's a nice compliment to a multitool like a traditional SAK that has no one hand opening blade.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login