Leatherman Wave Quality Control
-
@Leathermended It! said:
Any ideas on how to fix the scissor spring in the meantime? That spring steel doesn't really bend and stay bent.Careful :ahhh. As suggested post some pics. The key issue is the registration between the two scissor parts governed by the dimple in the hole so photograph the other side. Your spring part is sitting too high (and higher than allowed by either of my Wave type scissors).
Do the scissor parts have the same relative position from closed to open or just when locked?
-
Looking again at your pic I can see the bottom of the hole on the fixed arm. I can see where the dimple has been punched. It looks to me that the dimple must be broken or unformed. Look on the other side.
If the retailer won't refund (not sure of sales law in your jurisdiction) you haven't much to lose and a lot to gain by a LM warranty fix of all the issues.
-
Not a good indicator for Leatherman when the quality of their flagship tool is degenerating. You'd think at least they'd step up the quality control related to the Wave.

Sent from my iPad using Tapatalk
-
-
It's threads like this that make me want to dig my PST collection out and give each one a big fat kiss. They don't make them like they used to.
-
@zoidberg said:
Can you take a bunch more pics? Ends, sides, inside handles with tools out of the way etc. And don't try bending the scissors spring.Here are some more pics. I couldn't really get a good inside handles pic. The black residue isn't as bad now because I spent a while opening and closing the tool and wiping off the black, inner handle coating material. The other plier face isn't as bad, but it still has big scratches that don't show up on camera well. I didn't bother with the scissor spring.


Other Side

After opening and closing the scissors a bit, they won't even open a little bit.


@sawman said:
It's threads like this that make me want to dig my PST collection out and give each one a big fat kiss. They don't make them like they used to.I know, it's bad, but I think that leatherman quality control has been a bit off and on for a lot of years now. People have been discussing their QC since the early 2000s.
-
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?
-
Rub on the plier head is normal where it presses into the handle.
Some of those marks look out of place though, more like from use.
Does the small bit driver and large flat driver deploy easily?
The scissor spring looks like it isn't bent enough.
Would have to recommend sending it back. -
If you arent happy Id send it back to MEC. Ive returned stuff there before no problem. I bought a wenger cast Ti scaled SAK, that weird looking one. I was so jaw droppingly unimpressed I returned it the next day no hassles.
-
If keeping it, could tweak handle insides something like this...

Flat blade about width of inner handle an pull an push inward a wee bit where scuff marks appear.
On one set of Wave I got I did this as it was annoying, no issue now.
I suppose this will upset purists but it is what it is, a tweak.Just throwing it out there is all.
Edit to add, hope I don't get booted for that suggestion lol.
-
@Leathermended It! said:
Can you take a bunch more pics? Ends, sides, inside handles with tools out of the way etc. And don't try bending the scissors spring.
Here are some more pics. I couldn't really get a good inside handles pic. The black residue isn't as bad now because I spent a while opening and closing the tool and wiping off the black, inner handle coating material. The other plier face isn't as bad, but it still has big scratches that don't show up on camera well. I didn't bother with the scissor spring.


Other Side

After opening and closing the scissors a bit, they won't even open a little bit.


@sawman said:
It's threads like this that make me want to dig my PST collection out and give each one a big fat kiss. They don't make them like they used to.I know, it's bad, but I think that leatherman quality control has been a bit off and on for a lot of years now. People have been discussing their QC since the early 2000s.
I can't recall hearing to many QC gripes about the Wave...? Perhaps I tuned them out.
Sent from my iPhone using Tapatalk
-
@Leathermended It! said:
Can you take a bunch more pics? Ends, sides, inside handles with tools out of the way etc. And don't try bending the scissors spring.
Here are some more pics. I couldn't really get a good inside handles pic. The black residue isn't as bad now because I spent a while opening and closing the tool and wiping off the black, inner handle coating material. The other plier face isn't as bad, but it still has big scratches that don't show up on camera well. I didn't bother with the scissor spring.


Other Side

After opening and closing the scissors a bit, they won't even open a little bit.


@sawman said:
It's threads like this that make me want to dig my PST collection out and give each one a big fat kiss. They don't make them like they used to.I know, it's bad, but I think that leatherman quality control has been a bit off and on for a lot of years now. People have been discussing their QC since the early 2000s.
I can't recall hearing to many QC gripes about the Wave...? Perhaps I tuned them out.
Sent from my iPhone using Tapatalk
They haven't been too widespread, but the wave is really the everyman's multitool, so maybe Leatherman thinks that it can get away with slightly lower standards than tools like the ST300 or OHT. Just speculation. Here is an interesting post with some valid points.
http://edcforums.com/threads/is-leathermans-build-quality-dropping.50926/
Anyways, I'm not that worried about leatherman going down some deep dark pit of poor quality, I just want Leatherman to know that the community is keeping track of any bad apples. -
@captain spaulding said:
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?That was a good idea. I oiled them with WD40 and they still stick a bit and don't open as far as they should, but at least they are usable now.
Does anyone have experience securing a bit extender into one of the side pockets? I just don't want to lose it because it holds my robertson bit, pretty essential for Canadians. I have heard that a metal pen clip works, but I don't think that I have one of those. Thanks!
-
@Leathermended It! said:
@captain spaulding said:
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?
That was a good idea. I oiled them with WD40 and they still stick a bit and don't open as far as they should, but at least they are usable now.
Does anyone have experience securing a bit extender into one of the side pockets? I just don't want to lose it because it holds my robertson bit, pretty essential for Canadians. I have heard that a metal pen clip works, but I don't think that I have one of those. Thanks!


For now I found a old string stop, it stops ext from falling through case in my use.
Edit, sorry, I see you want to carry bit in ext? I don't think will do you any good.
-
the scratches on the plier head look like what happens from over time. Mine had no scratches when i got them but have gained them through opening and closing, which makes no sense for a new one.
-
@Leathermended It! said:
@captain spaulding said:
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?
That was a good idea. I oiled them with WD40 and they still stick a bit and don't open as far as they should, but at least they are usable now.
Does anyone have experience securing a bit extender into one of the side pockets? I just don't want to lose it because it holds my robertson bit, pretty essential for Canadians. I have heard that a metal pen clip works, but I don't think that I have one of those. Thanks!


For now I found a old string stop, it stops ext from falling through case in my use.
Edit, sorry, I see you want to carry bit in ext? I don't think will do you any good.
The string stop is a really good idea. The only reason that I ever considered putting the bit in the extender is that my extender has really strong retention and I need to use the pliers to get the bit out. It just sucks having one loose robertson bit and no real place to put it. The area behind the velcro is an option, bit it's almost impossible to fish the single bit out. Maybe I need to integrate a mini magnet pen into my EDC. :P
-
@Leathermended It! said:
@Leathermended It! said:
@captain spaulding said:
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?
That was a good idea. I oiled them with WD40 and they still stick a bit and don't open as far as they should, but at least they are usable now.
Does anyone have experience securing a bit extender into one of the side pockets? I just don't want to lose it because it holds my robertson bit, pretty essential for Canadians. I have heard that a metal pen clip works, but I don't think that I have one of those. Thanks!


For now I found a old string stop, it stops ext from falling through case in my use.
Edit, sorry, I see you want to carry bit in ext? I don't think will do you any good.
The string stop is a really good idea. The only reason that I ever considered putting the bit in the extender is that my extender has really strong retention and I need to use the pliers to get the bit out. It just sucks having one loose robertson bit and no real place to put it. The area behind the velcro is an option, bit it's almost impossible to fish the single bit out. Maybe I need to integrate a mini magnet pen into my EDC. [emoji14]
Curious what you do to solve single bit carry issue.
Do tell when you discover that part.Are you keeping the Wave or exchanging it?
Edit to add, I forgot to say, if the ext bit holder really holds and you need pliers to remove, a drop of machine oil or WD inside tip where lock ring is that holds bit, helps greatly.
-
@Leathermended It! said:
@Leathermended It! said:
[quote author=captain spaulding link=topic=59337.msg1086148#msg1086148 date=1431306205]
Just putting it out there in case you have not done so. Did you try putting oil on the spring of the scissors and working them for a while?That was a good idea. I oiled them with WD40 and they still stick a bit and don't open as far as they should, but at least they are usable now.
Does anyone have experience securing a bit extender into one of the side pockets? I just don't want to lose it because it holds my robertson bit, pretty essential for Canadians. I have heard that a metal pen clip works, but I don't think that I have one of those. Thanks!


For now I found a old string stop, it stops ext from falling through case in my use.
Edit, sorry, I see you want to carry bit in ext? I don't think will do you any good.
The string stop is a really good idea. The only reason that I ever considered putting the bit in the extender is that my extender has really strong retention and I need to use the pliers to get the bit out. It just sucks having one loose robertson bit and no real place to put it. The area behind the velcro is an option, bit it's almost impossible to fish the single bit out. Maybe I need to integrate a mini magnet pen into my EDC. [emoji14]
Curious what you do to solve single bit carry issue.
Do tell when you discover that part.Are you keeping the Wave or exchanging it?
Edit to add, I forgot to say, if the ext bit holder really holds and you need pliers to remove, a drop of machine oil or WD inside tip where lock ring is that holds bit, helps greatly.
[/quote]Thanks for the tip on the lock ring. I think that I might make a mini single bit card to fit in the area behind the velcro. I am still on the fence about returning it. My tools are all users and I can handle the scratches on the pliers, I may still send it back on account of the other issues.
-
I know this has been done before, I just made one for myself.
Is this applicable to yourself maybe?

-
My wave also has that, it is designed that way so that the tool doesn't open in your pocket. My wave is also scratched on the pliers. I absolutley hate leatherman's way they designed their way to keep the tools open and closed. It is 100% garuanteed that it will not last 25 years. On al my leatherman tools it wore out in a year, some tools wore out in a month others in half a year. Their is no engineering behind it. It is just designed on luck or something. On some tools it works good, on others it never worked good.
They could learn something from victorinox who uses springs and has notches in the plier so it locks open and closed.No offence but i think it is funny that there are treads here where they show you how you can adjust your new tool with hammers, screwdrivers and torx bits.
Leatherman is an excellent brand and designes great stuff, and every time my new tool is deliverd to my house my excitement is killed because i have to adjust it again and the standard problems occur again.If you buy a new Mercedes you don't have to adjust the doors so that they close properly or are hard to open, even on the cheapest car you don't have to do that.
A new product should function good from the factory, no work needed. (you pay for it)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
