Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Kosmo's Projects

Scheduled Pinned Locked Moved The Mod Squad
36 Posts 1 Posters 4.6k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Kosmo's Projects
Kosmo's Projects
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kosmo Offline
    kosmo
    Posts: 1,199
    kosmo Offline
    kosmo
    wrote on last edited by kosmo
    #21 Quote Reply

      @Syph007 said:
      Since you're experimenting with peening more than I did, here are some thing for you to try.

      Use a carriage bolt as the backing. Put it in a bench vice as a test.

      This way each side of the rivet is getting hit by a domed surface. When I was playing I found it gave pretty nice results with lots of light hits.

      If you find you'd like to hit the heads more to form them better but don't want the sak any tighter, put a shim stock or razor blade in during assembly. Then peen to your hearts content and pull the shim when done. Its best to cut rectangle with a V notch and push it in so the shim surrounds the pin as much as possible. Also coat it with oil.

      :tu:

      I got this watchmaker's (peening) hammer from Harbor Freight (a source of cheap tools here in the US). I found nicer polished ones on-line, but at $4.99 it was about 1/4th the cost of ordering something similar on-line with shipping.

      I estimated the head weighs about 2 1/4 oz while the entire hammer weighs ~3 oz. (Not sure how these measurements compare to others, head vs entire hammer?) It comes with two rounded steel tips. I'm going to see if I can get a bolt (probably metric) to mount the second round tip on a platform below the knife being worked on and hammer from the top.

      Fastly error: unknown domain 151.101.1.124

      favicon

      (www.harborfreight.com)

      watchmaker-hammer.jpg

      1 Reply Last reply
      • Syph007 Offline
        Syph007
        Global Moderators
        Posts: 9,842
        Syph007 Offline
        Syph007
        Global Moderators
        wrote on last edited by
        #22 Quote Reply

          I buy alot of my supplies from Jeweler supply places so I pick up msc things there when I order.

          The hammer I use most is a 2 oz basic one from Gesswein. The $4 one. :D

          http://www.gesswein.com/c-142-jewelers-hammers.aspx

          They've got much fancier ones though but the basic one does the job for me.

          1 Reply Last reply
          • kosmo Offline
            kosmo
            Posts: 1,199
            kosmo Offline
            kosmo
            wrote on last edited by
            #23 Quote Reply

              I've included an image below to try to illustrate my question. The photo is not quite accurate, because I mirrored the image of the Electrician's blade to switch sides in the photo.

              I've been thinking about what obstacles would prevent having two small blades on one layer opposite each other (on an 84mm Alox)? The key ring spacers would be needed on both ends to take up space because of the thickness of the back spring. But from what I've looked at they should fit without modification. What other obstacles might there be in attempting to make a layer like this?

              1 Reply Last reply
              • Syph007 Offline
                Syph007
                Global Moderators
                Posts: 9,842
                Syph007 Offline
                Syph007
                Global Moderators
                wrote on last edited by
                #24 Quote Reply

                  Just the position of the nail nicks really. If its an outer layer youd want both nicks facing out, but thats not possible. If its an inner layer, maybe it can fit in such a way both nicks are accessible?

                  1 Reply Last reply
                  • kosmo Offline
                    kosmo
                    Posts: 1,199
                    kosmo Offline
                    kosmo
                    wrote on last edited by
                    #25 Quote Reply

                      @Syph007 said:
                      Just the position of the nail nicks really. If its an outer layer youd want both nicks facing out, but thats not possible. If its an inner layer, maybe it can fit in such a way both nicks are accessible?

                      That should be OK because the Electrician's blade is wider and nail nick will be up higher. It would be toward the inside and above the can opener.

                      1 Reply Last reply
                      • kosmo Offline
                        kosmo
                        Posts: 1,199
                        kosmo Offline
                        kosmo
                        wrote on last edited by
                        #26 Quote Reply

                          I'm roughing out an idea to create a peening fixture. Using a second rounded tip underneath to peen against. If it looks like it will work, I'll probably see if I can cut a channel in some HDPE to minimize movement of a the knife while peening to try to minimize hammering outside the effective diameter of the brass rod being peened. I should also be able to adjust the height of the lower rounded tip so it won't come into contact with the Alox scales.

                          I still need to pick up some metric parts (bolt, washers and nuts) that I assume I will need to attach to the rounded tip. These pictures give you a rough idea of what I'm trying to do.

                          1 Reply Last reply
                          • captain spaulding Offline
                            captain spaulding
                            Posts: 20,793
                            captain spaulding Offline
                            captain spaulding
                            wrote on last edited by
                            #27 Quote Reply

                              Very cool and it looks like you have caught the modding bug!

                              1 Reply Last reply
                              • kosmo Offline
                                kosmo
                                Posts: 1,199
                                kosmo Offline
                                kosmo
                                wrote on last edited by
                                #28 Quote Reply

                                  :cheers:
                                  I enjoy doing this kind of stuff, although I kind of limited not having access to a machine shop.

                                  The peening is kind of an art, although I thought maybe I can eliminate some problems, mostly to cosmetic mistakes that are easy to make.

                                  1 Reply Last reply
                                  • kosmo Offline
                                    kosmo
                                    Posts: 1,199
                                    kosmo Offline
                                    kosmo
                                    wrote on last edited by
                                    #29 Quote Reply

                                      Peening fixture with some controlled variability.

                                      From my previous experience and that explained by Syph007 it would probably be better to work on the two outer rods first and tighten the knife blades and then finish the knife working on the inner pin, not making it too tight. With that in mind I made this fixture that uses the middle pin as a registration point to help minimize hitting the alox scales during peening.

                                      I made this fixture using a liner as a gauge to drill the holes. The peening tip underneath can be raised and lowered using shims. It is also a little off center by ~1/16" or ~1.5mm so it will allow the peening tip to come in contact with different parts of the rod depending on how it is rotated. I use leather on top to help protect the upper surface (bottom photo).

                                      1 Reply Last reply
                                      • Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        Posts: 9,842
                                        Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        wrote on last edited by
                                        #30 Quote Reply

                                          I applaud your enthusiasm for experimenting with the riveting! Great to see what you come up with. :tu:

                                          1 Reply Last reply
                                          • kosmo Offline
                                            kosmo
                                            Posts: 1,199
                                            kosmo Offline
                                            kosmo
                                            wrote on last edited by
                                            #31 Quote Reply

                                              A fish scaler pickle getter in an 84mm? It would probably work with an 84mm saw blade back spring, but the spring will need to be thinner or perhaps the use of a shim washer?

                                              1 Reply Last reply
                                              • Syph007 Offline
                                                Syph007
                                                Global Moderators
                                                Posts: 9,842
                                                Syph007 Offline
                                                Syph007
                                                Global Moderators
                                                wrote on last edited by
                                                #32 Quote Reply

                                                  You can use the spring from the 91mm. Cut the end off and use it as a shim then shorten the spring. There was someone else on here a year or more ago that put a fishscaler on an 84mm that way.

                                                  1 Reply Last reply
                                                  • kosmo Offline
                                                    kosmo
                                                    Posts: 1,199
                                                    kosmo Offline
                                                    kosmo
                                                    wrote on last edited by
                                                    #33 Quote Reply

                                                      I've got an urge to start another 84mm Alox mod. Perhaps a Micro-Farmer? Perhaps a serrated Micro-Farmer?

                                                      I've still got a mega blade knife on my mind.
                                                      Is there another 84mm large blade to fill out a four layer?

                                                      Normal main blade
                                                      Serrated main blade
                                                      Youth main blade (butter blade)
                                                      ?

                                                      Small pen blade
                                                      Clip point small blade
                                                      Electrician's blade
                                                      Pruner blade

                                                      1 Reply Last reply
                                                      • kosmo Offline
                                                        kosmo
                                                        Posts: 1,199
                                                        kosmo Offline
                                                        kosmo
                                                        wrote on last edited by kosmo
                                                        #34 Quote Reply

                                                          ♫ Should ♫ they ♫ stay ♫ or ♫ should ♫ I ♫ build ♫ now? ♫

                                                          - YouTube

                                                          Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.

                                                          favicon

                                                          (www.youtube.com)

                                                          1 Reply Last reply
                                                          • kosmo Offline
                                                            kosmo
                                                            Posts: 1,199
                                                            kosmo Offline
                                                            kosmo
                                                            wrote on last edited by
                                                            #35 Quote Reply

                                                              Continuing on my bone scale project. I've got them prepared for forming. I was considering working with the bone scales and the brass liners with a sanding wheel. Do you think I should work with these two materials (bone and brass) separately?

                                                              1 Reply Last reply

                                                              Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                              Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                              With your input, this post could be even better 💗

                                                              Register Login

                                                              • 1
                                                              • 2
                                                              1. Home
                                                              2. Tool Talk
                                                              3. The Mod Squad
                                                              4. Kosmo's Projects
                                                              Reply
                                                              • Reply as topic
                                                              Log in to reply
                                                              COMMUNITY LINKS
                                                              EDC-TV SAKWiki GearFeed SAKSelector
                                                              Operational Funds

                                                              Help us keep the Unworkable working!

                                                              Make A Donation
                                                              November Goal: $300.00
                                                              Due Date: Nov 30
                                                              Total Receipts: $0.00
                                                              Below Goal: $300.00
                                                              0% funded
                                                              • Login

                                                              • Don't have an account? Register

                                                              • Login or register to search.
                                                              • First post
                                                                Last post
                                                              0