Alox TLC
-
Myself, spray the crap out of it with Ballistol. Use the doubled ended nylon toothbrush dealies like for gun cleaning to scrub what I can reach, long wooden stick double ended Qtips to get down in there. Gun patches on those dental pics made for gun cleaning.
If the gunk is hardened and bad, I use the synthetic safe gun scrubber first to blow out stuff and loosen crud up. As gun scrubber takes out all the oil and stuff too, I'll spray with Ballistol after. I mentioned synthetic safe Gun Scrubber cause that's just what I have on hand for use on my Glocks or other plastic guns. Found out once that the plastic stock on a Mossberg shotgun doesn't care for regular Gun Scrubber. Lol. Oops.
After its cleaned up and wiped out very well, little Militec in the joints. Tiny bit.
I know many use the dish soap method with great success as well.
-
Dunk it in some hot water and liquid soap, with all the tools half opened. After a few hours, I take the SAK out, I wash it inside and out, let it air dry for another few hours, then apply some fine oil :)
-
You are welcome.

-
Keurig!
That's Dutch for Good job! Bad joke, I know. Nice coffee maker.
-
-
Good for making ramen noodles too.
Nate
That's us mobile -
Thanks for all the suggestions everyone.
Santos you are now on "The List"
-
@HarleyXJGuy said:
Thanks for all the suggestions everyone.Santos you are now on "The List"
Herley,mate,your loosing it

He was on The List ages ago!
-
On most knives WD-40 is sufficient. If more cleaning is needed I go the hot soap bath route. I like to use pipe cleaners to wipe out the areas between the liners. A fine screwdriver works well on cleaning out packed-in gunk between the outer liners, where the blade contacts the spring when open.
-
Not an expert on the subject, but doesn't the dishwasher detergent corrode aluminium? I've always been told not to wash aluminium dishes in the washer...
-
According to Victorinox you shouldn't put them in the dishwasher at all.
-
Thanks for all the suggestions everyone.
Santos you are now on "The List"
Herley,mate,your loosing it

He was on The List ages ago!
Yeah but in my defense I am getting old.
-
Thanks for all the suggestions everyone.
Santos you are now on "The List"
Herley,mate,your loosing it

He was on The List ages ago!
Yeah but in my defense I am getting old.
Hey, that's my
excusedefense! -
@Lynn LeFey said:
Before listening to anything I have to say on the matter, keep these things in mind...- I'm lazy
- I mostly don't know what I'm talking about.
I've gotten a number of knives off ebay that have been pretty ick filled. If they have scales, I remove them. Then, either way, I open all tools and soak the knife in very hot water with Dawn dish detergent for 'a while'. I check periodically, and swish it through the water to see if crud is coming off. Once it seems like the crud is soft enough, I brush it down with an old toothbrush, repeating the soak/scrub until I'm happy. Then, I rinse thoroughly in cold water, shake it dry, and pat it down with a paper towel, then leave the knife wrapped in the paper towel for maybe ten minutes to catch whatever water is left.
Next, I blast the whole thing to soaking with WD40, and shake off as much excess as possible, then another paper towel wrap for a few minutes. After this, I'll start opening and closing tools, to see how they're moving. usually, if there's crud in the joints, it starts coming out as a dark oily looking substance. I'll just work the tools open/closed until it stops leaking dirty oil. Repeat the WD40 soak as needed. I assume this is the slow way to accomplish what ultrasonic cleaners do quickly.
Once the WD40 looks clean, a thorough shake off, towel dry, and let it sit for a bit, maybe half an hour.
Finally, go back in with 3-in-1 oil at the joints, replace scales, and done.
This has worked remarkably well to clean up pretty heavily gunked up tools. It usually only takes one round of WD40 to get it done.
I feel confident in saying that nothing i do in this process would mess with your alox scales, or brass liners. I'd personally avoid a dish washer, as I just don't think that's a method with enough detailed cleaning used. Dish washers are good at big, flat things, not stuff with 'nooks and crannies'.
+1 !!
This is almost identical to my process with the slight exception of using compressed air if I'm wanting to pocket the thing immediately, and I alternate between 3 in 1 and MMO lube. Always pleased with the results.
Especially on board with points 1 and 2 Lynn... :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
