Amazing Gerber Service
-
Dunc I changed my original post a little so Gerber will still love ya :D
The one they sent me is a standard 600.
Dennis
-
-
Dennis I was only kidding :D
Dunc
Yea, I kinda figured that :D
Dennis
-
I found an old broken non-locking Gerber multitool in some trash about 6 years ago. One of the plier jaws had been broken off and the can opener tool had snapped off. It certainly led a hard life.
Motivated by this thread, I finally got around to sending it in to Gerber for warranty service on July 28th. I sent the bare tool along with a note describing these problems.

I got a package today:

Inside I found two belt pouches. One contained my old broken tool, the other contained a brand-new Multi-Plier 600 Bluntnose with tungsten carbide wire cutter inserts.

The old tool bears the engraved X 'condemned' mark. I'm sure they don't want to see this old tool again!

Though I found this broken Multi-Plier just a few years ago, I have another Multi-Plier MP600 that I have had for about 10 years. It has served me well. I recently upgraded to a Victorinox Swisstool Spirit, but the old MP600 still feels familiar and comfortable in my hand.
-
Congrates mate, although I doubt they'd off needed the note explaining the problem :D
So what are your thought's on the new one mate ???
-
I was surprised to see the new tool was a blunt nose, but looking at what was left of the old tool it surely was a bluntnose too. I never knew the old one when it was whole. :D Good for Gerber trying to replace my old tool with a new one as closely as possible.
The blade on the new tool was absolutely awful. It was one gigantic burr, and had two small chips out of the edge. I would have been hard pressed to cut myself on it, let alone anything else. After about 15 minutes on the Sharpmaker it will shave hair now. :D I don't recall Gerber's blades being so lousy. The serrated blade was somewhat better, I had to work a slight burr off the back of the blade, but that isn't unusual.
I've had a MP600 for about 10 years or so, so this new tool feels familiar, <FLICK>! My old MP600 lives in my tool bag I keep at work.
The Multitool world sure has come a long way...the multi-plier design has been surpassed by some of the newer tools. I picked up a Vic Spirit about 6 months ago and I absolutely love it. I stopped trying to flick it after a week or so, but I still occasionally find myself opening it up to get to the tools.... ::) I might have to alternate carrying the Vic Spirit with this new Gerber on occasion... :o
-
Yeah tool familiarisation can be a real double edged sword can't it :D
As for the burr's I had a similar story with the Diesel, I don't think there quality control is always what it good be at Gerber :-\
-
Yeah, the burr was so pronounced I thought for a second it must be a chisel... :D At least the steel is decent enough to take a nice edge.
Continuing my Gerber Multi-Plier saga, my wife found a non-locking Multi-Plier in darn near perfect condition about a year or so ago lying on the ground at a coin-op car wash. Joints and tools are loose but otherwise great condition. I'm considering sending it in requesting tightening.... >:D
-
@speederino said:
Yeah, the burr was so pronounced I thought for a second it must be a chisel... :D At least the steel is decent enough to take a nice edge.Continuing my Gerber Multi-Plier saga, my wife found a non-locking Multi-Plier in darn near perfect condition about a year or so ago lying on the ground at a coin-op car wash. Joints and tools are loose but otherwise great condition. I'm considering sending it in requesting tightening.... >:D
May as well abuse the privilige :D
-
bit OT but IF i was to get a gerber mt ,whats the best of them???
i dont want to hear about lightweight weights,not a word about some scissors and toothpick clockwork tools :D
want it to be sturdy. -
@Tarrodemierda said:
bit OT but IF i was to get a gerber mt ,whats the best of them???i dont want to hear about lightweight weights,not a word about some scissors and toothpick clockwork tools :D
want it to be sturdy.Diesel or one of the MP600 series :), the others sadly aren't in the same league :(
-
im so out from grid.
mp600 SERIES?
so mp6hundred aint any specific model? -
The MP600 represents about 9 or 10 variations on a fundamental theme. Bluntnose or Needlenose, some have variations in their tool selection such as saws and scissors. Any of the MP600's are great tools, pick one with the variations that suit you needs.
-
Yep Mr Speedy's got it right, just pick the MP600 with the best tool load out for you :)
-
Here here, quit mucking about and get this one:

Its the newest MP600 version, with:
blunt nose jaws (also in needlenose)
black finish (also in stainless)
carbide wire cutters
Wharnecliffe knife blade
square phillips driver
every blade locks
no blade clumps
Made in USA:)
-
I have been carrying a blunt nosed 600 for many years. I just did a little modding on mine a couple weeks ago to customize my tool load a little and updated to the new plier head.
I have used gerbers warranty service twice. very pleased both times with the outcome.
-
@J-sews said:
Here here, quit mucking about and get this one:
Its the newest MP600 version, with:
blunt nose jaws (also in needlenose)
black finish (also in stainless)
carbide wire cutters
Wharnecliffe knife blade
square phillips driver
every blade locks
no blade clumps
Made in USA:)
"quit muckin" :D
well that looks nice,only the can opener and small flathead is disturbing :D
saw blade exchanger ?i could use one. -
@Tarrodemierda said:
bit OT but IF i was to get a gerber mt ,whats the best of them???The answer to that should be obvious...

:D
Def
-
Mate i like the MP600 and the MP400 CS is also pretty nice. :D
-
I have little experience with Gerber tools I ahve had owned a shortcut which was great ( I broke it through stupidity) and the 800 which I am really impressed with it has been used for a variety of things from gardening to housebreaking and never once felt like it wasn't up to the task if it had a decent woodsaw it would be a great multi
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



