Wenger PocketGrip Variations
-
When it was first announced at the 1998 Shot Show, this little tool from Wenger was called the MiniGrip. More closely resembling a Swiss Army Knife than any other multitool before or since, the MiniGrip was Wenger’s second foray into the multi-purpose plier arena. Its predecessor had been the gigantic SwissGrip, based upon the 120mm Ranger series of knives, which had been criticized as being too large and bulky. Hoping to address these accusations, Wenger condensed the features of the MiniGrip into a much smaller package.

For those unfamiliar with this unusual looking device, I suggest you check out DavidBinGA’s review of it HERE.
As originally introduced, the MiniGrip had red cellidor scales (housing the characteristic SAK tweezers and toothpick, of course!) and could be obtained with either needlenose or blunt nose plier jaws. Other features and blades remain the same, with one notable exception…

Along with the two different plier-nose styles, there were also two styles of knife blades found on the PocketGrip. Most models I've seen came armed with a plain-edge spear point knife blade, but a fully serrated spear point blade is also available. Unfortunately, neither style locks open.

At some point within the first couple years of its existence, Wenger gave this little tool a new name, and the MiniGrip now became known as the Swiss PocketGrip. As near as I can determine, no other changes were made at this time except for the name.

Perhaps some folks had issues with the red cellidor scales being too fragile? Or perhaps Wenger was simply going for a more rugged look to appease the folks in Marketing. In any case, the next variation of their little multitool to appear was the Iron PocketGrip. It had handle scales of solid 1mm thick stainless sheet metal, which shed nearly 5mm off from the width of the entire tool. Slimmer and sleeker, the only downside to the Iron PocketGrip was the loss of the tweezers and toothpick compartments. (That, and it wasn’t RED anymore…..)

Now here is a subtle change; on all PocketGrips up to this point, the little serrated plier-lock tab, necessary on account of the tool’s spring-loaded plier jaws, was actuated with a sliding motion. At around the time of the Iron PocketGrip’s introduction, this slide-action lock was changed to a pivoting action. I believe the reason for this improvement can be found back in David’s review, where he rightly points out how easily the sliding lock can be accidentally tripped when using the bit driver.
I find the pivot-action lock to be much more secure.

With the exception of the Iron PocketGrip, all of the plier tools in this series seem decidedly on the wide and fat side. Most extreme in this regard was the next variation, called the Porsche Design Multitool. It is a whopping 12mm thicker than the already-plenty-wide red cellidor models, thanks mainly to its two handle scales of contoured Ruthenium (purplish-gray colored material from the platinum family).

On the plus side, the Porsche tool comes equipped with a tire-tread depth gage (excellent quality, but of dubious practical value) and a corkscrew, neither of which can be found on other PocketGrip models.

The most recent addition to the PocketGrip family is the 799 model, introduced in 2006. It features scales made of solid brushed aluminum, both of which are faceted in a sort of “octagon” style. Like the Iron PocketGrip with its stainless steel scales, the 799 does not have slots for tweezers or a toothpick. All other features however, remain the same.

Along with the introduction of the model 799, Wenger changed the model designation for all of the PocketGrip line last year. As can be seen above and at their website HERE, the Iron PocketGrip became the model 200, and the needlenose red cellidor version became the model 577. The blunt nose models no longer appear on the Wenger website.
Never very common, at least two of the variations shown above never even made it to the North American market. A quick check of the Wenger NA website shows only the Porsche tool available. And while there is no question that the MiniGrip/PocketGrip series of tools is not the most practical multitool design in history, the construction of these devices is typical of the stellar quality we’ve come to expect from Wenger.
-
Wow! These reviews of yours keep me interested in learning more about multi-tools. Really nicely done!
@J-sews said:
These little tools are not common. I’ve only handled a few, and so cannot say conclusively, but every one I’ve seen with needlenose pliers has a plain-edge spear point knife blade, and every one I‘ve seen with blunt nose pliers has a fully serrated blade. Perhaps this is just a coincidence, I don’t know for sure...It's just a coincidence. I have a blunt nose with a plain-edge spear point blade in the "multitool trade" section of these forums (</topic/571).
-
These little tools are not common. I’ve only handled a few, and so cannot say conclusively, but every one I’ve seen with needlenose pliers has a plain-edge spear point knife blade, and every one I‘ve seen with blunt nose pliers has a fully serrated blade. Perhaps this is just a coincidence, I don’t know for sure...
It's just a coincidence. I have a blunt nose with a plain-edge spear point blade in the "multitool trade" section of these forums (</topic/571).
Ahh! Thank you sir, I shall edit that portion of my post immediately.
-
Glad to have been of service.
You and the other multi-tool historians should write a book ...but post all the chapters here. ;)

-
I do love that tool. I've never been fond of the serrated blade on mine, or the way the bit holder is snapped in, but it still sees some use.
I need one of those metal ones. Does the 799 have a more comfortable grip than the Iron model?
-
-
What a great review :) I really like the iron ones .Another one to add to the growing list ::)
Dunc
-
I have the red handled blunt nose-serrated pocket grip. I'm using it at work more than my XLT and OH-fireman

-
Wow! What a great review.
I really like these tools....wish I had one. I guess they may be found outthere somewhere.
Thanks for this thread!
:)
-
Hi everybody. I'm new on this forum, and I have two short questions regarding the Porsche design model:
Are there more tools on the Porsche design model than on the other Pocket Grips ?
Are You sure, that the scales are plastic ? I've read, Ruthenium is a metal akin to Platinum.
-
Welcome to the forum Anson! If you like tools, this is the place to be...
WengerNA.com lists quite a few Porsche designed tools:
http://www.wengerna.com/browse/browse.jsp?cat_id=1&sub_cat_id=23
They've been running them for a few years now, but I can't comment on the handle material as they are all well out of my price range.
Def
-
@Anson Argyris said:
Hi everybody. I'm new on this forum, and I have two short questions regarding the Porsche design model:Are there more tools on the Porsche design model than on the other Pocket Grips ?
Are You sure, that the scales are plastic ? I've read, Ruthenium is a metal akin to Platinum.
Welcome. The handles are indeed Ruthenium which is from the Platinum family. They are awesome (I am fondling one right now). That is definitely one reason they are so expensive.
-
@Anson Argyris said:
Are You sure, that the scales are plastic ? I've read, Ruthenium is a metal akin to Platinum.
Welcome. The handles are indeed Ruthenium which is from the Platinum family. They are awesome (I am fondling one right now). That is definitely one reason they are so expensive.
Thanks for the additional info guys. I went back and removed the plastic note from my original post.
-
About how much do they run for, that Porsche is actually the first Wenger I've seen that I liked, besides the big one, what's it's name? The Ultimate? :-X :-\
-
The Giant is the unofficial name. Officially it's called the Every Implement Tool.
Def
-
@Viper said:
About how much do they run for, that Porsche is actually the first Wenger I've seen that I liked, besides the big one, what's it's name? The Ultimate? :-X :-\All of Wenger's Porsche tools fetch a high premium. Suggested retail on this model was $180.00 I believe.
Felinevet has one available for considerably less money than that HERE.
-
Well it's too late for that, but I couldn't have gotten it anyway. I only have about 50 US dollars, and once I go back to work this summer, I'm going to put all my money toward my next prize: a Victorinox SwissChamp XAVT.
-
Check with Felinevet (www.felinevet.sosakonline.com) for the XAVT. I believe he has the best price to be found anywhere.
Def
-
It appears that this "Felinevet" man has the answer to pretty much everything.
-
great review there mate!
add some of those to the list too, as for them being slip joints, thats a good thing in a lot off markets, like here in the UK
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login