Modded tti
-
Indeed. They seem to work well enough.

-
Most of us have done similar Josh. Hope it heals up good. Nice work mate.

-
:o ER visits suck! Hope it heals up well for ya!!
Nice mod BTW!

-
I have done a similar mod, I used a chainsaw file to open up the scissors pivot hole, I didnt like the idea of scissors spinning around on a drill! Hope your finger heals up ok!

-
Nice mod! Sorry about your hand. Hope you heal up fast.
Nate
That's us mobile -
What you need is a 7-year old to hold the sharps for you. ;)

You will never be rid of that

-
Nice Mod !
the tool not the finger mod :D
-
Past the tendon?
I hope you got inside stitches, otherwise it will get looser than a fake SAK... -
Holy Toledo!
I do hope you heal completely brother Josh.
-
Healing up pretty well! Talked with Jeff about getting my charge Cerakoted. Hopefully will be sending it off next week. Still cannot believe how dumb I was. Although, I had a couple few wobbly pops.... so that may have had something to do with it....

-
Wobbly pops tend to have that effect! :D
Sent from my iPad using Tapatalk
-
@firefightingjosh said:
Healing up pretty well! Talked with Jeff about getting my charge Cerakoted. Hopefully will be sending it off next week. Still cannot believe how dumb I was. Although, I had a couple few wobbly pops.... so that may have had something to do with it....

Jeff does great work! You won't be disappointed.

-
IVe done the same exact thing but with a SAK blade. Got careless and was only holding the blade with my hand and the bit caught and sliced deep into my thumb.
I made a very simple board now for holding sharps on my drill press. Basically just a small piece of plywood as the bed but with a strip of wood screwed and glued to the back that sticks up about an inch from the surface. That way when I drill if a bit catches in the part it drives the part into the wood sticking up instead of my thumb.

The only other tip for drilling out metal is use lube. If there are any metal fragments on the drill wipe them off and lube again. I use mineral oil since I have that in abundance, but there are proper cutting oils too, which Ive not yet tried.
-
Been there... done that (not quite as deep, tough). It actually happened with a 1/2" chuck hand-held drill set at very low RPMs - it actually twisted my hands due to its extreme torque motor.... I learned my lesson and now hand and eye protection are a must when handling any power tools.
-
Wot?

I was going to recommend my hack for improving the scissors cutting performance, might not be needed though.
Do you have a link to this mod?
-
Wot?

I was going to recommend my hack for improving the scissors cutting performance, might not be needed though.
Do you have a link to this mod?
-
Could someone tell me the size drill bit needed to drill out the wingman scissors to put them in the charge like this? Was going to check before I left the house this morning and forgot. Thanks.
-
@carlb said:
Could someone tell me the size drill bit needed to drill out the wingman scissors to put them in the charge like this? Was going to check before I left the house this morning and forgot. Thanks.I used a file with my one.
I've not measured them myself but I believe from what I've read here the Wingman scissors pivot is 3/16 and the Charge saw pivot is 7/32.
Hope that info helps you. -
Thank you that helps me out a lot.
-
Remember to take lots of pics and come join the club.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login