What did you use your Leatherman for today?
-
Thank You Kampfer for Kampferman Can Opener .. best all around..

-
I used the scissors on my Surge to trim my thumb nail, I hit it with a hammer in February and it died, the new nails been growing through and I caught it and ripped the old nail off. I trimmed it up so that I won't catch it again because it was bloody painful!
I also cut a lot of rope into shorter pieces for a T-bar at work.
-
@Henry said:
I used the scissors on my Surge to trim my thumb nail, I hit it with a hammer in February and it died, the new nails been growing through and I caught it and ripped the old nail off. I trimmed it up so that I won't catch it again because it was bloody painful!I also cut a lot of rope into shorter pieces for a T-bar at work.

-
not sure if i want to see pics. i lost a few finger nails myself.
-
@ducttapetech said:
not sure if i want to see pics. i lost a few finger nails myself.Yep, been there done that .
-
Not today, but over the weekend I built a kydex press using my Rebar and my CRKT minimalist. My brother laughed at me for not using power tools, but it didn't take much longer than using power tools would have. Not much of a press, just two planks, some foam padding, rubber bands and sit on the whole thing.
Ham pressed by an oversize lawn gnome. Not done yet, so no pictures yet.
-
I used the scissors on my Surge to trim my thumb nail, I hit it with a hammer in February and it died, the new nails been growing through and I caught it and ripped the old nail off. I trimmed it up so that I won't catch it again because it was bloody painful!
I also cut a lot of rope into shorter pieces for a T-bar at work.

Have you not seen the Surge scissors before? Nice size and pretty handy.

Unless you meant this.... in which case I won't make other people look
-
I used the scissors on my Surge to trim my thumb nail, I hit it with a hammer in February and it died, the new nails been growing through and I caught it and ripped the old nail off. I trimmed it up so that I won't catch it again because it was bloody painful!
I also cut a lot of rope into shorter pieces for a T-bar at work.

Have you not seen the Surge scissors before? Nice size and pretty handy.

Unless you meant this.... in which case I won't make other people look
V-cut on ReBlaster Maximun power !!

-
I used the pliers on the PST II to undo a knot in my son's shoelace.
-
Used my ST300 to help my sister in law move. Couldn't fit a futon through the door, so I used the flat driver to pop out pins and take the door off. Still didn't fit, so out came the bit kit and adapter to undo the hex screws holding the futon together, and we took it out in pieces.
-
@eddie1115 said:
Used my ST300 to help my sister in law move. Couldn't fit a futon through the door, so I used the flat driver to pop out pins and take the door off. Still didn't fit, so out came the bit kit and adapter to undo the hex screws holding the futon together, and we took it out in pieces.Nice!
-
Today they get a WD40 tune-up.
.jpg)
-
I used my leatherman squirt PS4 to help repair the water jets on my wife's Dodge Journey.
Sent from my electronic multi-tool.

-
Just installed an ethernet outlet using my Wave's pliers, wire stripper and knife

Real simple thing to do as it turned out, took me around 3 minutes :)
-
I've been carrying my BO Mini all week. Today smurf hit the fan when I received more stock than I could handle.
I needed to re-merchandise a large area,and put new shelves in. The only shelves available were knackered. The mounting tabs were bent up to 90 degrees out. Much to my surprise and delight,the Mini worked a charm straightening them!
:ahhh :ahhh :ahhh MINI! :ahhh :ahhh :ahhh
-
Used my Skeletool to re-attach some key hooks to the laundry room wall. I had forgotten how well the drivers work.
Also used Skeletool to cut some paracord for wife.
-
I used my PST II scissors to cut out a form for one of my coworkers and the pliers to hold a nut from spinning while we were fixing our door handle.
-
Used my wave to hold a bolt on my headboard while I tightened the nut with a wrench, then I used a modded saw blade(thx Baldux) in the pocket clip slot to shorten the bolts. Finished them smooth with the file.
-
Used my Wingman to help repair my bike.

Should have used the wave, screwdrivers/prybars that fold in on ones fingers are quite annoying!
Sent from my XT1068 using Tapatalk
-
Took apart a Traxxas eRevo axle and cut out a Papa Murphys coupons with my Charge TTI.
Sent from my iPad using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login