And so it begins.... (My adventures into Alox!)
-
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?
And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
:)
-
@twiliter said:
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
:)
A small blade is a wee bit thinner than the awl, so I make little washers to fill out the remainer of the space, but other than that they fit no problem.
91mm file works on the 93mm saw spring with no changes needed (other than making the pivot hole bigger).
:D
-
A couple of questions for you Syph, and maybe this was covered elsewhere, but what is required to put a small blade in a 93mm in place of the awl, is there a factory spacer that works?
And, is the file from a 91mm a direct drop in on a 93mm saw spring?
Thanks in advance, I'm trying to figure out what to send you for a custom, if you're willing and still taking 93mm requests.
i
:)A small blade is a wee bit thinner than the awl, so I make little washers to fill out the remainer of the space, but other than that they fit no problem.
91mm file works on the 93mm saw spring with no changes needed (other than making the pivot hole bigger).
:D
Thanks, will continue on PM...

-
I still have a decent stash of BO'd 93mm parts but they dont get asked for too often. Here is one I put together today on request. A good combination of tools in 3 layers. :D





-
Beautiful BO double blade Syph...even better on the 93mm frame so they can be on opposite pivots. Nice work.
-
Excellent work.

You had to go and ruin it with the combo tool though. :P
-
I got some more 91mm alox in. I machined a tweezer slot in a few this time. :D
I love this 4 layer setup. Lots of tools and still reasonable on thickness. Every layer has a backtool and no hook on scissors layer for the hook haters either... :D
CNC machined 6061 Al scales
Black hard anodized
Brass liners
Brass Nub on tweezers- combo tool / main blade / phillips
- metal file / chisel
- wood saw / fine driver
- scissors / awl







-
I forgot the customer wanted the wire cutter mod to the scissors so I added that. Id never tried it before but wow it does actually cut wire pretty darn good.



-
Just made it through this entire thread. Amazing work, Syph. I'm inspired. Seeing as how you don't work on 84mm, I may take a stab at modding my Cadet. If I may ask, can the saw from a 84mm Lumberjack replace the blade in a Cadet. Usually the saw in an 84mm pivots on the "fat" end. Will it work on the skinny the end in place of the blade?
-
@MachoGrande said:
Just made it through this entire thread. Amazing work, Syph. I'm inspired. Seeing as how you don't work on 84mm, I may take a stab at modding my Cadet. If I may ask, can the saw from a 84mm Lumberjack replace the blade in a Cadet. Usually the saw in an 84mm pivots on the "fat" end. Will it work on the skinny the end in place of the blade?Wow you need a prize for reading the whole thread! :D The saw only works on the saw backspring as far as I know. Its not a tapered tools like a blade and its the same thickness the whole way, so its not a good tool to share with another tool in the same layer.
-
I promoted 3 stock alox saks to Electrician + scissors config. :D



-
Love the OC's, thinking about round 2 even before 425 arrives...

Nice work Syph!

-
Just made it through this entire thread. Amazing work, Syph. I'm inspired. Seeing as how you don't work on 84mm, I may take a stab at modding my Cadet. If I may ask, can the saw from a 84mm Lumberjack replace the blade in a Cadet. Usually the saw in an 84mm pivots on the "fat" end. Will it work on the skinny the end in place of the blade?
Wow you need a prize for reading the whole thread! :D
Thanks! I'll let you know where to send my free custom sak! :D
Thanks for the info regarding the saw. That makes a lot of sense as to why I never see a 93mm saw sharing a layer with something like an awl.
So if I was looking for a slim, bladeless 93mm sak that featured a saw, a cap lifter, an inline phillps and an awl, could the awl sit opposite the inline phillips next to the cap lifter?
-
I forgot the customer wanted the wire cutter mod to the scissors so I added that. Id never tried it before but wow it does actually cut wire pretty darn good.



any guidance on the scissor mod for wire cutters? it looks straight forward, but, looks can be deceiving
I used a small diamond bur that came with my dremel to make the cutouts then cleaned up the edges with a stone, and that was it. I was expecting it to be more annoying but it was pretty straight forward.
-
I forgot the customer wanted the wire cutter mod to the scissors so I added that. Id never tried it before but wow it does actually cut wire pretty darn good.



any guidance on the scissor mod for wire cutters? it looks straight forward, but, looks can be deceiving
I used a small diamond bur that came with my dremel to make the cutouts then cleaned up the edges with a stone, and that was it. I was expecting it to be more annoying but it was pretty straight forward.
sounds good, at about what opening angle of the scissors did you do the drilling? (closed, 30 degrees, etc)
-
I forgot the customer wanted the wire cutter mod to the scissors so I added that. Id never tried it before but wow it does actually cut wire pretty darn good.



any guidance on the scissor mod for wire cutters? it looks straight forward, but, looks can be deceiving
I used a small diamond bur that came with my dremel to make the cutouts then cleaned up the edges with a stone, and that was it. I was expecting it to be more annoying but it was pretty straight forward.
sounds good, at about what opening angle of the scissors did you do the drilling? (closed, 30 degrees, etc)
Oh I did it full open, then kept grinding until they mated up just right.
I used a bit that looks like the one on the right in this pic.

-
One of the last little blades I had made went into a pioneer yesterday. These really are too thick for my preference so next time I try making some it will be on thinner material. These are 0.160" thick blades. The pliers layer is 0.125" for reference. :D



-
Very cool!!!!!!

-
That's a beast of a blade, and really cool

Sent from my XT901 using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login