Bike porn thread
-
@captain spaulding said:
Here is my 1985 Miyata 610. It still needs some work, but is ride-able and I have been riding it a lot recently. It needs a new wrap for the grips. Derailleur adjustment and the brake cables are rusted so probably a complete brake overhaul. The brakes barely work. It also needs a wheel truing. I have a Nashbar AT-1 coming in, in a few days so the Miyata will not be getting much love or money put into it anytime soon, but at least I will have it as a backup. It's to tall for me anyways. Even with the saddle slammed all the way down the length to the pedals is still not a proper length. I can ride it though.
hi capt,this is a bit different than the miyata you showed in the pic, but still a nice old tourer,

The picture I posted in the other thread was not mine as stated. Its the EXACT same bike just different colors. The only difference is where the gear shift is.
-
I picked this up a couple weeks ago. It is a frankenstein of sorts with a cyclocross frame, assorted Campy, Shimano and XTR parts.
-
@captain spaulding said:
[quote author=captain spaulding link=topic=5435.msg1113857#msg1113857 date=1435903736]
Here is my 1985 Miyata 610. It still needs some work, but is ride-able and I have been riding it a lot recently. It needs a new wrap for the grips. Derailleur adjustment and the brake cables are rusted so probably a complete brake overhaul. The brakes barely work. It also needs a wheel truing. I have a Nashbar AT-1 coming in, in a few days so the Miyata will not be getting much love or money put into it anytime soon, but at least I will have it as a backup. It's to tall for me anyways. Even with the saddle slammed all the way down the length to the pedals is still not a proper length. I can ride it though.hi capt,this is a bit different than the miyata you showed in the pic, but still a nice old tourer,

The picture I posted in the other thread was not mine as stated. Its the EXACT same bike just different colors. The only difference is where the gear shift is.

yours has center pull brakes and pictured one has canterlevers,ive got a few old sets of weinmann centerpulls,there classics,be nice too see yours back on the rode capt
-
This is the first bike in a long time that has knobby tires on it. I am itching to take this things out on some trails and see how it does

-
@ToolJoe said:
This is the first bike in a long time that has knobby tires on it. I am itching to take this things out on some trails and see how it does
Im sure it will go well mate,i sometimes use my audax bike off road and thats not even got knobblys on :D although i dont ride it as hard as my mtb's

-
yours has center pull brakes and pictured one has canterlevers,ive got a few old sets of weinmann centerpulls,there classics,be nice too see yours back on the rode capt
Not exactly sure what that is as i'm not real familiar with this style bicycle.
-
The Nashabr AT-1 I ordered was not supposed to be here until Monday, but it looks like its out for delivery today!

Hopefully I do not have much trouble putting it together.

-
So the Nashbar AT-1 came in today. I unpacked everything and was looking for the assembly instructions. Problem is they do not give you any. Nothing. I called the company and was told they do not include assembly instructions with their bicycles. This is the first time I have built a bike from the box, but I would assume you would get instructions. Guess I was wrong. Anyways, I had to buy some grease and a pedal wrench to do the assembly properly. Not a big deal, but it kind of sucks. So I assembled everything and all is well.
I am assuming once I put the proper tension on the front brakes I can cut the rest of the cable off right? How much should I leave?
The grips are interesting and quite comfortable. From the limited riding I did with it today I don't really like the twist shifting, but it is what it is.
One thing I noticed is the wheels aren't true right out of the box, but not enough for me to pay to have them fixed.
-
BUMP. I need to confirm its alright to cut the brake cable.
-
Everything looks seated correctly (assuming left hand front as you're in the US), you have two small Philips screws on the side of the break, they adjust the tension of the spring so you can make sure both sides contact the rim at the same time.
-
@Henry said:
Everything looks seated correctly (assuming left hand front as you're in the US), you have two small Philips screws on the side of the break, they adjust the tension of the spring so you can make sure both sides contact the rim at the same time.I tried to do that, but the screw does not seem to be adjusting anything. I tightened the cable and tried to fine tune the left side brake pad to be closer to the rim, but when screwing (left moves the brake pad closer) the screw just backed out all the way without adjusting the brake pad at all. The brakes work, but not real well as the brake handle will pull all the way to the grip and barely stop the bike. If I use both brakes at the same time the bike stops well but if I use either the front or rear brake alone they will only roll the bike to a slow stop. Should I tighten the adjustment screw for the brake pad all the way, then tighten the cable, then back out the screw to push the brake pad to proper alignment?
I can cut that long front brake cable and put a cap on the end right? How much should I leave?
-
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:
Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
-
@Henry said:
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
I will just have to fiddle with it and see what I can do. The brakes work well enough to be safe so i'm not to concerned but would like to get them working perfectly without having to pay $75 for a tune up.
Do you mean leave 2''-3'' on the cable and cut there? I don't think I can tuck it into the caliper.
-
@captain spaulding said:
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:
Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
I will just have to fiddle with it and see what I can do. The brakes work well enough to be safe so i'm not to concerned but would like to get them working perfectly without having to pay $75 for a tune up.
Do you mean leave 2''-3'' on the cable and cut there? I don't think I can tuck it into the caliper.
2" to 3" should be good, just so that the cable doesn't slip off when not under tension (ie. when adjusting the cable later on)
Nice looking set of wheels you got there, cap'n

I gotta get my "new" Nishiki 352 hybrid sorted out, just waiting for the smurfing postal services to deliver my parts

-
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.
-
@captain spaulding said:
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.That belonged to another thread...
-
@captain spaulding said:
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.
That belonged to another thread...
It belongs in both as I was talking about the cable in this thread.

-
I finally got the time and $$ to put new tires on my bike. I got a set of puncture-resistant semi-slicks and new tubes for $60 installed. The change was instantly noticeable. The bike handles better and the ride is not as sluggish on the pavement as it was with the off-road rubber it came with.
One or two more little things and my department store mountain bike will be a nice urban ride.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




