Bike porn thread
-
Everything looks seated correctly (assuming left hand front as you're in the US), you have two small Philips screws on the side of the break, they adjust the tension of the spring so you can make sure both sides contact the rim at the same time.
-
@Henry said:
Everything looks seated correctly (assuming left hand front as you're in the US), you have two small Philips screws on the side of the break, they adjust the tension of the spring so you can make sure both sides contact the rim at the same time.I tried to do that, but the screw does not seem to be adjusting anything. I tightened the cable and tried to fine tune the left side brake pad to be closer to the rim, but when screwing (left moves the brake pad closer) the screw just backed out all the way without adjusting the brake pad at all. The brakes work, but not real well as the brake handle will pull all the way to the grip and barely stop the bike. If I use both brakes at the same time the bike stops well but if I use either the front or rear brake alone they will only roll the bike to a slow stop. Should I tighten the adjustment screw for the brake pad all the way, then tighten the cable, then back out the screw to push the brake pad to proper alignment?
I can cut that long front brake cable and put a cap on the end right? How much should I leave?
-
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:
Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
-
@Henry said:
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
I will just have to fiddle with it and see what I can do. The brakes work well enough to be safe so i'm not to concerned but would like to get them working perfectly without having to pay $75 for a tune up.
Do you mean leave 2''-3'' on the cable and cut there? I don't think I can tuck it into the caliper.
-
@captain spaulding said:
To see the adjustment those small screws make, you squeeze the lever and see it return. Each side is going against the other. The pad itself will be adjusted by a 5mm. Leave around 2-3" and then tuck it into the caliper:
Its fine fettling to set them up perfectly, a back you only get through lots of experience and helps put people like myself through college!
I will just have to fiddle with it and see what I can do. The brakes work well enough to be safe so i'm not to concerned but would like to get them working perfectly without having to pay $75 for a tune up.
Do you mean leave 2''-3'' on the cable and cut there? I don't think I can tuck it into the caliper.
2" to 3" should be good, just so that the cable doesn't slip off when not under tension (ie. when adjusting the cable later on)
Nice looking set of wheels you got there, cap'n

I gotta get my "new" Nishiki 352 hybrid sorted out, just waiting for the smurfing postal services to deliver my parts

-
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.
-
@captain spaulding said:
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.That belonged to another thread...
-
@captain spaulding said:
I cut the cable and tried putting the cap on and crimping. Since the MT's I used to cut the cable sucked the big one (Rebar and MP400) the end was frayed. I could not get the cap on and almost gave up and while putting the tools away noticed my Teflon tape. I got the idea to use a small piece and wrap the end of the frayed cable. It worked to keep the together and let the cap slide on enough for me to crimp it down.
That belonged to another thread...
It belongs in both as I was talking about the cable in this thread.

-
I finally got the time and $$ to put new tires on my bike. I got a set of puncture-resistant semi-slicks and new tubes for $60 installed. The change was instantly noticeable. The bike handles better and the ride is not as sluggish on the pavement as it was with the off-road rubber it came with.
One or two more little things and my department store mountain bike will be a nice urban ride. -
@jerseydevil said:
I finally got the time and $$ to put new tires on my bike. I got a set of puncture-resistant semi-slicks and new tubes for $60 installed. The change was instantly noticeable. The bike handles better and the ride is not as sluggish on the pavement as it was with the off-road rubber it came with.
One or two more little things and my department store mountain bike will be a nice urban ride.Awesome! I am waiting on my bag and light mount.
-
I still owe you some pics of my new work and family carrier.
As I am still in paranting time - and for a good part could not move well - I only have tested it a few times with my son and used it instead of my bike as having electric power was so much nicer on my hurting knees and feet.As mentioned before, my Boss bought the bike as my work vehicle and I may use it in my free time, too. We bought a Kid seat and rain-roof to make it a Kid transporter. My son likes it very much but you need to keep an eye out for the Cargo - He tends to try to unload the bike while we ride...
I present teh Babboe CityE:



-
That looks pretty cool. Is it hard to steer with the extended wheelbase?
-
That's a fantastic ride mate! I really do think the bicycle is key to our environmental woes :)
Sent from my K013 using Tapatalk
-
Now that's a proper bakfiets!

-
Well the Nashbar is starting to disappoint. First off the bike needs a complete tune up right out of the box. Derailleurs are out of wack and the chain hits it in certain gears. Wheels are not true. Brakes don't work very well and the latest development is the JUNK pedals they provide have already broken (less than a week) after very light riding. I'm kind of pissed off right now.

-
Can you take it back as it sounds like its not fit for purpose???
Sent from my K013 using Tapatalk
-
@Mike, Lord of the Spammers! said:
Can you take it back as it sounds like its not fit for purpose???Sent from my K013 using Tapatalk
Cannot return it. It really just needs a full tune up and new pedals. I ordered new pedals which will be here in a couple of days. I will most likely try and do the tune up myself, but would hate to make anything worse. With that said I like to be able to work on things I own so I will definitely be doing it myself. I also do not have money to spend on doing a tune up and no way to get the bike to the shop anyways. To do it properly I am going to have to buy a "work stand" or whatever its called which sucks, but I kind of want one anyways so I will see if I can get the stand eventually. The pedals are easy enough to replace. I have a fear of ruining the threads on the crank arm and having to replace that as well, but if it happens then so be it.
I'm just really bummed as the damn bike needs a brake adjustment, derailleur adjustment, wheel truing, and new pedals right out of the box. I'm stuck with the bike now. I really do love the look and design of the bike though so once everything gets sorted I expect to be very happy, but I will always be pissed off about having to do all this extra crap after spending a bunch of money on a brand new bike. -
Bikes are packed from Taiwan etc, and then every single bike at a shop has these adjustments, if you skip the shop part, then you have to do them yourself. The good thing is, its not rocket science, so if you're mechanically minded you can easily do it yourself. I no longer work in bike shops, but I do everything apart from suspension cartridge service that requires nitrogen.
I wouldn't worry about stripping your cranks, just use a 15mm wrench. The pedal axle themselves will be 9/16" with a coarse thread, so its not easy to cross thread, and if its stiff then don't force it! Cranks mainly strip when they receive and impact and don't have steel inserts.
You don't NEED a bike stand, but they make working a lot easier. Though it is essentially just a way to secure the bike with the wheels in the air. When I first started racing I can't count the number of times I tuned my gears with the bike upside down in a muddy field. If you have a garage/shed just having something suspended from the rafters will be more than adequate for the odd job.
If you do get into cycling more however, it can be just as addictive, and every more expensive than knives and tools!
-
Good luck in getting your bike road worthy, Captain!
I did test ride a few different load carrying bikes and the 3 wheeled versions are very clumsy in handling, slow and tend to tip over in fast curves.
The 2 wheeled bikes rides like a usual bicycle after around 2 blocks of getting used to. You need to look where you ride, not stare at the front wheel. Otherwise you get used to the length pretty quick. Until now I used a bike trailer when carrying tools at work and I like the long bike much better.
Steering is not as quick as on a usual bike and some pedestrian crossings are a bit tight. Most annoying is people using the (narrow) bike path the wrong way and then yelling at you because you are not disappearing in smoke as they approach.The bike itself, while a basic load carrying bike, is nicely equipped. Rear hub brushless engine (250W, 3 levels of support up to 25 km/h), Rear brake is a Magura hydraulic barke, front is a drum brake combined with hub dynamo, automatic LED lighting. The box is waterproof plywood.
I am thinking about making the front (drum) brake a bit more efficient - The 40 feet long cable with a million bends eats a good amount of the applied force.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
