The Hacked Leatherman Owners Club.
-
Finally stuck the Rebar plier head onto my Wave. Doing a cable cut test (/post/1113037) convinced me that my modded Wave (+ Wingman scissors, small flat driver and awl) was superior to the Rebar for in almost every way - except for the cable cutters. Only had to modify the locking pin for the blade, shorten the small flat driver and clean up the back of the awl to make it fit.
-
Nice job !
-
Thanks Steve.
I've had the Wave and the Rebar for nearly a year now and though I've modded both I've never really gelled with either. Always preferred the feel of the Wave over the Rebar but favoured the Rebar's pliers. Hopefully now I've got the best of both. -
Good job Harry.
This reminds me I still need to get mine done.
Breezy where did you go?
-
@HarleyXJGuy said:
Good job Harry.This reminds me I still need to get mine done.
Breezy where did you go?
I'm still here... just busy these days. Check your PMs mate. ;)
-
@hiraethus said:
Finally stuck the Rebar plier head onto my Wave. Doing a cable cut test (/post/1113037) convinced me that my modded Wave (+ Wingman scissors, small flat driver and awl) was superior to the Rebar for in almost every way - except for the cable cutters. Only had to modify the locking pin for the blade, shorten the small flat driver and clean up the back of the awl to make it fit.Harry did you have to do anything special to make the awl and two flat drivers to fit. Is the smaller flathead from the Rebar?
-
They're all modified in some way. The small flat head is from a Kick/Fuse/Blast and it's been shortened and had a little taken off the underside to clear the lock mechanism. The large flat head is from a Rebar and it's been shortened to clear the pliers rest in the handle. The awl is from a Rebar too, and I ground the back down so it cleared the pliers head.
-
Very nice Hiraethus, looks like exactly the loadout I'm planning. Out of interest have you put your Rebar back together yet? I'd be interested to see that. I was thinking of trying to fit the left overs in, and then potentially turning it into a blunt nose plier tool.
-
Not yet - I think it'll be a bladeless blunt nose version of the Rebar with scissors. I've already ground the pliers from a Blast down, now I just need to pull the bit driver from another mod and swap everything over.
-
So get around the length of the scissor issue by putting them down the side? I hadn't thought of that but if its being set up as a '2nd' tool then it makes sense.
-
I've already fitted a pair of Wave scissors to the Rebar - I ground the thumb pad down a bit to fit - so I'll reuse them.
-
Kick-A.S.S. version 2 to meet Restrictions on knives in California schools
-
@Kampfer said:
Kick-A.S.S. version 2 to meet Restrictions on knives in California schools

-
My Wave is now modded... a rebar plierhead with the s30v and serrated/hook blade from a Charge - should have just got a charge but because it was a gift and sentimental I wanted to keep the wave...

-
@Beynon5 said:
My Wave is now modded... a rebar plierhead with the s30v and serrated/hook blade from a Charge - should have just got a charge but because it was a gift and sentimental I wanted to keep the wave...Great job man! I like the look of large Torx screws by the outside tools on the Wave better than the Knurled screw on the charge. By the way do you have any plans for your dismantled Charge? If not Id be interested in buying or trading for the remains.

-
My Wave is now modded... a rebar plierhead with the s30v and serrated/hook blade from a Charge - should have just got a charge but because it was a gift and sentimental I wanted to keep the wave...
Great job man! I like the look of large Torx screws by the outside tools on the Wave better than the Knurled screw on the charge. By the way do you have any plans for your dismantled Charge? If not Id be interested in buying or trading for the remains.

I agree with that about the torx :) and unfortunately I never had a Charge - I bought the blades from TexasToolCrafters however I did buy a rebar for the plierhead...
-
Void Warranty from Leatherman


-
@Beynon5 said:
My Wave is now modded... a rebar plierhead with the s30v and serrated/hook blade from a Charge - should have just got a charge but because it was a gift and sentimental I wanted to keep the wave...You ain't got to make excuses to mod stuff for no reason around here. We all are on board with it.
-
Kickman
[ftp=ftp://forum.multitool.org/index.php/topic,61437.msg1139391.html#msg1139391]/post/1139391[/ftp]
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
