SOG Switch Plier 2.0
-
well, scissors are made of two blades, so How is it going to work if two blade are not together?

-
@SOG said:
SCISSORS * ° LARGE 2 SLOTS- Special positioning required
° PowerLock exclusive component
Scissors and Wirecutters MUST be positioned on the far left side of any configuration
- Special positioning required
-
@SOG said:
SCISSORS * ° LARGE 2 SLOTS
- Special positioning required
° PowerLock exclusive component
Scissors and Wirecutters MUST be positioned on the far left side of any configuration
It says large tool, far left, two slots, not two long slots. And I'm guessing the second slot would be for the spring (which is shorter than the scissors themselves) ergo making it able to fit in a small slot, I had planned on removing can opener and file. So let's reserve the :twak: until it has been tried. :tu: thanks for the link tho. That is helpful. :salute:
- Special positioning required
-
The scissors should fit in the file slot. That's where I put the wire strippers. Works great. :)
-
I want some too, smkw only had saw, file, knife, and Phillips.
-
Demel, what plastic on switch plier are you talking about?
Nate
That's us mobile -
@ducttapetech said:
Demel, what plastic on switch plier are you talking about?Nate
That's us mobileAren't the black scales made from a hard plastic? I could be wrong, but It doesn't seem like steel, unless it is a very light and thin steel.
-
Demel, what plastic on switch plier are you talking about?
Nate
That's us mobileAren't the black scales made from a hard plastic? I could be wrong, but It doesn't seem like steel, unless it is a very light and thin steel.
Not sure what Demel is talking about, but I can assure you that on my SwitchPlier, the scale are definitively metal (also tested that it is ferromagnetic) and pretty thick.
-
@Omar Rapace said:
Demel, what plastic on switch plier are you talking about?
Nate
That's us mobileAren't the black scales made from a hard plastic? I could be wrong, but It doesn't seem like steel, unless it is a very light and thin steel.
Not sure what Demel is talking about, but I can assure you that on my SwitchPlier, the scale are definitively metal (also tested that it is ferromagnetic) and pretty thick.
You are right. I just assumed because of the weight it was plastic. After looking closer it is metal. That is even better. Sog has done great with this tool
-
Picked one up a few weeks ago, I like it. It has a very good tool selection, and the tapered end makes for a more comfortable use of the tools. Had to ditch the godawful combo blade that SOG makes though, put in a plain edge one then swapped the sides that it and the file were on.
I just wish it had a better pocket clip, and that SOG would stop plastering their name on every square inch of the tool.
-
If anyone successfully fit scissors into it I like to see.
-
@Kampfer said:
If anyone successfully fit scissors into it I like to see.I just called sog to see if they had any in stock. The rep said he spoke to the warranty department and he didn't suggest putting scissors in because they may or may not interfere with the plier head. :-\ I will still order some to test it out.
-
After using it for a while, I do believe I will replace the blade with__________. It has the perfect setup for a bladeless multi. I'm thinking combing it with a mini vulcan or mini grip. I wanted a knifeless fuse, but this will work out better.
Edit:
Has anyone tried carrying one in a sheath? -
Alright, I think I cracked the code too...
"50ft-trad": hope you don't mind but I was too curious to wait for your pictures 
My current config, from scissors to blade:
[list type=decimal]-
Scissors
-
thin metallic spacer (1x)
-
Can opener
-
thin metallic spacer (2x)
-
Phillips
-
Bottle opener / Large flat screwdriver
-
Knife blade
Not an ideal set of tools but a good starting point to experiment. Everything opens and closes smoothly and pliers deploy and close as expected. Oh, and you don't even need to deploy the pliers to access the scissors!
For reference, here is the original tool layout (don't remember about any spacer/washer):
[list type=decimal]-
File
-
Awl
-
Can opener / small screwdriver
-
Phillips
-
Bottle opener / Large flat screwdriver
-
Half serrated knife blade




-
-
@Omar Rapace said:
My current config, from Scissors to blade:
Nice.
Any chance you could list the original layout as well?For reference, here is the original tool layout (don't remember about any spacer/washer):
[list type=decimal]-
File
-
Awl
-
Can opener / small screwdriver
-
Phillips
-
Bottle opener / Large flat screwdriver
-
Half serrated knife blade
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




