AWT Benchmade Griptilian scales.
-

Edit: beat me to it steve :D
-
I recieved the AWT kit and donor Griptilian. I have to admit it did feel slightly strange getting a brand new $100 knife and immediately disassembling it.
I did take a few pictures during the process. Nothing in detail, but enough to see what is going on.
Donor Griptilian and AWT Kit.
The kit comes with screws (which you will have to use) that are different from the originals. Backspacer, and scales. No instructions on instillation. One thing I would of liked to know is you will need a T6, T10, and a 1/16 allen. You will re-use your original pivot and pivot screw for the kit.
Griptilian disassemble.
Grip going into AWT kit.
I installed the scales on both sides and then screwed everything together lightly, leaving the blade and pivot out.
cleaned and re lubed (with CRK grease) the washers.
After greasing the washers I started to put the pivot pin in (it is shaped like the letter D so it will only go in one way. Inserted it and let it protrude only slightly. Slid on the first washer. Pushed in the pin further and installed the blade. Pushed it in further and installed the last washer and inserted the other screw. Sounds easy, but this was one thing that took a bit of time. I will explain later. Once you do this you are basically done.
Deciding which clip to use.
I have a bunch of different clips I could use for this and was originally going to do the black oxide clip, but placed the deep carry Contego clip on and it looked great. I had a tension problem with the clip. Removed it and reinstalled to find the tension was great, but the portion of the clip the first inserts into your pocket was much to low and I could not get it into my pocket. After trying to get it to work it was not happening so I went with my original plan and used the black oxide. Same tension issue so I bent the first one and it snapped in half. I was only bending with my fingers. Tried another and got it perfect and installed. Tightened all the screws down for the clip and scales. Last thing to do was center the blade and adjust the pivot which took about 5 minutes.
Shes all done!
Something to note.
One thing I noticed while installing was this gap. Even though it is there it has no effect on the strength or blade/frame play in any way.
Something else to note.
I noticed the factory Benchmade screws are no longer using loctite, but rather these plastic sleeve's. Seems very smart. It is not messy. It locks the screws in VERY well while at the same time acting as a sign of if the owner has disassembled the knife when sending in for warranty (I assume).
Blem
So I ordered the blemished kit as it is $25 cheaper and was the only one they had. I have to say I could barely even notice a blem at all. I think I spotted it and if this is how their blem kits look then I am definitely happy with that. There is a tiny spec of a blem on the edge.
Final thoughts.
Final thoughts are great so far. The blem kit was beautiful and the blem was tiny and not even really noticeable. The knife will get more wear than that in the first day for sure. Instillation was very straight forward and easy. Know in advance what size tools you will need and have a SAK handy as it helped with a few things like pushing the pivot pin and installing the last washer. The gap in the frame and the scales could be better, but to be honest this gap happens in your standard Spydercos and the like so its no big deal and I am not worried about it at all. The back spacer fits pretty dang good, but could be refined to be perfect. Still good enough that there are no complaints from me at all. Centering the blade and getting proper tension was easy. The one and only thing is the blade will not free fall as easily as it did right out of the box, but it opens just as smooth. I did flip around the washers so it might just be that and could break in well. Again, not even enough to have me concerned or care really. It makes the knife slimmer and carries beautifully in the pocket. Makes the Griptilian feel like a heavy duty performer. As of now I could not be happier. I love the scales. If I remember anything else I will add it later.
More Pics.
-
Looks great Cap! I wish they were just a touch less expensive, but ah well. I can't justify doubling the cost, but if it were "the" knife for me, I would in an instant. I really love the look of well machined aluminium
is it a lot heavier? -
Very nice Cap! How's the grip on those scales?
-
@Toolslinger said:
Very nice Cap! How's the grip on those scales?Well they do not have to much traction when running a finger over them, but when held in the hand I do not feel like the knife would ever slip out.
-
@SAKnight said:
Looks great Cap! I wish they were just a touch less expensive, but ah well. I can't justify doubling the cost, but if it were "the" knife for me, I would in an instant. I really love the look of well machined aluminium
is it a lot heavier?Honestly the price is very reasonable compared to other aftermarket scales. I got the "blem" set for $50. Other aftermarket scales are usually $90+. I don't disagree that I wish they were less than $50 still as we all want things to be less expensive. :D
-
@captain spaulding said:
Looks great Cap! I wish they were just a touch less expensive, but ah well. I can't justify doubling the cost, but if it were "the" knife for me, I would in an instant. I really love the look of well machined aluminium
is it a lot heavier?Honestly the price is very reasonable compared to other aftermarket scales. I got the "blem" set for $50. Other aftermarket scales are usually $90+. I don't disagree that I wish they were less than $50 still as we all want things to be less expensive. :D
It's very true. I was looking at endura scales briefly, all i found were more than the knife... But yeah, $50 really isn't that bad, they look damn fine, especially for "blemished"!
-
I just adjusted the pivot again and it is still centered and closes much smoother now.
-
I need to stay away from this thread, I almost talked myself into a set... :ahhh
-
I came close to buying a set after cap's first post and that was before seeing his shots of the finished product.
This forum is dangerous to one's wallet.
Not that I'm complaining, I encourage people too...

-
That looks a lot better than the original scales! I would like to see a stag set for that knife!
-
Great write up and awesome pics as always Capt. I do think this knife looks so much better that how it comes originally. The scales IMO really make the knife a $100 knife.
-
-
Nice pics!

I'm loving the color on the AWT. Kind of a Kelly/Hunter/Forest Green at least to my eyes. Whatever you call it, it's beautiful.
-
What's interesting to me, is that those are likely "blemish" because the color wasn't right. It said on the site most of them don't qualify, not because of chips or dings, but because of colors being out of range, which makes me wonder what they "should" be. I like the shade they are

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





































