Time to break a blade
-
Have a look over in the Mod Squad forum, there are a few threads on taking apart MP400s and 600s. For example: /post/928630
-
Agreed with the swap not the chop. Gerber are extremely easy to take apart and put back together. Only thing is to remember the washers have little tabs on them that must sit in a certain place into the handle. Its really easy to do though.
-
...so Red loctite for reassembly?
-
Hmm. Anyone got an MP450 file they'd sell me?
I feel like it isn't likely I'd find a washer of just the right thickness to keep the tension right.
-
@Smaug said:
Hmm. Anyone got an MP450 file they'd sell me?I feel like it isn't likely I'd find a washer of just the right thickness to keep the tension right.
You can always layer thinner ones to get the right thickness. Plus there is some leeway in the screw for tightening to get the tension right. Gerbers are built like AK's, a little sloppy on the tolerances, but rugged and reliable.
-
No! Use some of your wife's nail varnish (or some of your own :P). This will make the thread "gummy" enough to not come undone inadvertently, but also allow you to freely take it apart again if you need to. If you buy a MP450 to steal the file from, you then have a spare set of drivers to swap in if you damage one ;)
-
Or you can leave the loctite out. I've not had any problems with the pivots loosening on mine after modding them.
-
@Toolslinger said:
Or you can leave the loctite out. I've not had any problems with the pivots loosening on mine after modding them.This times a thousand. There is no way for the tools on a Gerber to spin the pivot, this no way to loosen the screw through repeated tool opening/closing
-
Hmm. Anyone got an MP450 file they'd sell me?
I feel like it isn't likely I'd find a washer of just the right thickness to keep the tension right.
You can always layer thinner ones to get the right thickness. Plus there is some leeway in the screw for tightening to get the tension right. Gerbers are built like AK's, a little sloppy on the tolerances, but rugged and reliable.
Yes, tension is against the tools and not the handle so as long as the tools clear the pliers you should be good.
Or you can leave the loctite out. I've not had any problems with the pivots loosening on mine after modding them.
This times a thousand. There is no way for the tools on a Gerber to spin the pivot, this no way to loosen the screw through repeated tool opening/closing
I've done six of these, they all worked loose and required loctite, so probably one for YMMV.
-
Hmm. Anyone got an MP450 file they'd sell me?
I feel like it isn't likely I'd find a washer of just the right thickness to keep the tension right.
You can always layer thinner ones to get the right thickness. Plus there is some leeway in the screw for tightening to get the tension right. Gerbers are built like AK's, a little sloppy on the tolerances, but rugged and reliable.
Yes, tension is against the tools and not the handle so as long as the tools clear the pliers you should be good.
Or you can leave the loctite out. I've not had any problems with the pivots loosening on mine after modding them.
This times a thousand. There is no way for the tools on a Gerber to spin the pivot, this no way to loosen the screw through repeated tool opening/closing
I've done six of these, they all worked loose and required loctite, so probably one for YMMV.
I stand corrected. YMMV it is, I've done two and been okay, and a pinchy :D
-
@Toolslinger said:
Why chop when you can swap?You could just take the knife out and replace it with another tool. The ones on other 400/600 series Gerbers will fit with some rearranging and consideration for tool length.
or
You can take the knife out and put in a washer/spacer to fill the gap.
Either way, you get a knifeless tool and still have the option of the blade if you decide to swap it back in at some point.
What he said.
Takes a little patience, plus you will have a knife blade for another great idea! -
At the very least, someone may want the drop point blade to replace their wharncliffe, I know that's a love/hate shape. Maybe they'd trade for it?
-
I´d like to add this:
/topic/47743
For some additional pics of disassembled Gerber Tools. I´ll always take gerber tools and if I have what you need, I´ll gladly trade.
if you just need a washer, I can send it in an envelope.And I can offer some broken blades ( basically, tool pivot area bits), so you don´t have to snap off yours...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


