And so it begins.... (My adventures into Alox!)
-
-
Please Syph, what is the mystery tool? I can't stand the suspense! :ahhh
I was hoping he'd have the parts cut this week, but looks like I'll have to wait until next week. Boy this will be a let down if they don't turn out! :D I'll show what I made anyhow though.
Can't wait, even though I've seen your design drawings :)
-
Back to some alox work today. Electrician with scissors :D



-
And my last set of white cerakote scales. :D



-
:ahhh
does that mean you won't be getting anymore white? -
-
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?
-
@MachoGrande said:
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?Nope. One just needs to be flipped around.
-
:ahhh
does that mean you won't be getting anymore white?I dont think i will do anymore cerakote at all actually.
Wait what?
What scales will you put on your Alox customs?
Just anodized ones and Ti. Ive got a bunch of Ti scales being cut with various options
-
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?
Nope. One just needs to be flipped around.
Ok, bear with me here. I'm new to this. No matter which way I swap the spring, I can't get it to work with the phillips. And if I could, the spring would stick out past the bottom of the scale. Do I need to mod the phillips? Or do I have the wrong Phillips?
-
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?
Nope. One just needs to be flipped around.
Ok, bear with me here. I'm new to this. No matter which way I swap the spring, I can't get it to work with the phillips. And if I could, the spring would stick out past the bottom of the scale. Do I need to mod the phillips? Or do I have the wrong Phillips?
Yes I believe you'll need to grind the lugs off the Phillips.
-
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?
Nope. One just needs to be flipped around.
Ok, bear with me here. I'm new to this. No matter which way I swap the spring, I can't get it to work with the phillips. And if I could, the spring would stick out past the bottom of the scale. Do I need to mod the phillips? Or do I have the wrong Phillips?
Yes I believe you'll need to grind the lugs off the Phillips.
Is that a 91mm?
-
[quote author=MachoGrande link=topic=34772.msg1140856#msg1140856 date=1440203703]
When doing the phillips-across-from-two-tools mod, do the opener layer springs need to be modded to accommodate the phillips?Nope. One just needs to be flipped around.
Ok, bear with me here. I'm new to this. No matter which way I swap the spring, I can't get it to work with the phillips. And if I could, the spring would stick out past the bottom of the scale. Do I need to mod the phillips? Or do I have the wrong Phillips?
Yes I believe you'll need to grind the lugs off the Phillips.
Is that a 91mm?
[/quote]The Phillips is from a 91mm. It's going in a 93mm project.
-
K
-
Ok, bear with me here. I'm new to this. No matter which way I swap the spring, I can't get it to work with the phillips. And if I could, the spring would stick out past the bottom of the scale. Do I need to mod the phillips? Or do I have the wrong Phillips?
Yes I believe you'll need to grind the lugs off the Phillips.
Thanks. Anyone else care to confirm before I totally ruin this phillips driver? :D
-
The lobster is right. Basically, you need to make the tang of the philips driver a similar size to the one on the cap lifter. You can adjust the angle of each face as well as the perpendicular distance from the pivot to change the angle of the driver relative to the spring, and you can change the radius of the corners to make it easier to open/close.
Make sure you leave enough material on to keep the snap and to ensure it doesn't drop too far into the knife when closed but take enough off that it's not too difficult to open and close.
Take it steady - easy to take too much off, difficult to put it back on again. ;)
-
@hiraethus said:
The lobster is right. Basically, you need to make the tang of the philips driver a similar size to the one on the cap lifter. You can adjust the angle of each face as well as the perpendicular distance from the pivot to change the angle of the driver relative to the spring, and you can change the radius of the corners to make it easier to open/close.Make sure you leave enough material on to keep the snap and to ensure it doesn't drop too far into the knife when closed but take enough off that it's not too difficult to open and close.
Take it steady - easy to take too much off, difficult to put it back on again. ;)
Thank you!
-
@Syph007 said:
This one was interesting as it's a bladeless model.I wanted to use the metal file backspring in the blade layer so I could use the phillips on the backside. The only problem is the metal file layer is thinner by 0.015" than the blade layer. So what I did was to mill off that much material from the flat pivot area of the phillips driver and it fit like a dream! :D
Syph - The "lock" on the main blade on the 93mm feels so much stronger then on the 91mm, and I've assumed this is largely because there is no back tool.
So now that you're able to put the cutout tools on other layers, is there a no-back tool spring that can be used with the main blade on the 91mm? Am I overstating the affect that the back tool has on the lock?
-
This one was interesting as it's a bladeless model.
I wanted to use the metal file backspring in the blade layer so I could use the phillips on the backside. The only problem is the metal file layer is thinner by 0.015" than the blade layer. So what I did was to mill off that much material from the flat pivot area of the phillips driver and it fit like a dream! :D
Syph - The "lock" on the main blade on the 93mm feels so much stronger then on the 91mm, and I've assumed this is largely because there is no back tool.
So now that you're able to put the cutout tools on other layers, is there a no-back tool spring that can be used with the main blade on the 91mm? Am I overstating the affect that the back tool has on the lock?
Nope there are no, no back tool blade backsprings that I know of. The main reason for the 93mm feel is significantly thicker and stronger backsprings than the 91s. At least thats what I think, but the shape probably plays a role too.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login