The Mega84
-
@50ft-trad said:
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
WE DEMAND A VIDEO! :ahhh
:D
Hear, hear!

I was referring to a 91mm metal saw earlier; I know 84mm ones are hard to find. Besides, newer ones are better ;)
I'm probably too late for this but what if you turned the pruner balde to a wharncliffe, a sheepsfoot or a bevel point? More function then. >:D :)
It was your preference of cellidor that I recalled, then.
Now you've got me thinking about a mod I had in mind... Will you be modding a Wenger next by any chance? :ahhh
-
@50ft-trad said:
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
WE DEMAND A VIDEO! :ahhh
:D
Hear, hear!

I was referring to a 91mm metal saw earlier; I know 84mm ones are hard to find. Besides, newer ones are better ;)
I'm probably too late for this but what if you turned the pruner balde to a wharncliffe, a sheepsfoot or a bevel point? More function then. >:D :)
It was your preference of cellidor that I recalled, then.
Now you've got me thinking about a mod I had in mind... Will you be modding a Wenger next by any chance? :ahhh
No vids, sorry.
I was tempted to use the MFV blade for turning into a wharncliffe actually. Unfortunately, it's only 2.0mm tang thickness and I need the 2.4 due to the awl tang thickness.
Yes, Wenger may well be next, but that's (hopefully) a MUCH simpler project :)
-
84mm saw springs are a PITA >:(
-
Awl spring is protruding a little, which means the Phillips is sitting high. I've marked it up with a sharpie marker to see if it can be reprofiled without compromising the spring under the cap lifter

-
Peening with a hammer drill, you've got to love it.

-
No video :'( :P
I was thinking of a Vic/Wenger frankenmod. I wonder if you could offer some insight on Wenger entrails once you got it open.
But that's not for now. You're tackling the first project yet.


-
That's not going to work grinding that off 
Bacon sandwich and cup of tea required while I think this through....

-
Bacon butty completed, Mega84 built up and clamped, and Phillips sits at an acceptable height with no spring modification (spring sits sufficiently off centre on the driver).
Commence operation "whack it with a hammer" :D
-
@50ft-trad said:
I really can't believe how well that works. They've actually slightly "over peened" and don't quite seat in the bushings, so I'm just tickling them up with a file. It actually gives a nice domed and burnished finish.Alox modders take note!
Ha, I had that idea and tried to peen an alox mod together... the drill got away from me and just ended up damaging the scales. I gave up on peening alox after that try. :D
As for pre peening I dont bother any more just put the rods through, cut to lenght and pen both ends.
-
Mega84 v1 is complete and operational





-
Very nice Al

-
It's not 100% perfect, and there is a tiny bit of daylight between the springs/liners, though it is fully functional.

-
@50ft-trad said:
I really can't believe how well that works. They've actually slightly "over peened" and don't quite seat in the bushings, so I'm just tickling them up with a file. It actually gives a nice domed and burnished finish.
Alox modders take note!
Ha, I had that idea and tried to peen an alox mod together... the drill got away from me and just ended up damaging the scales. I gave up on peening alox after that try. :D
As for pre peening I dont bother any more just put the rods through, cut to lenght and pen both ends.
Using the hammer drill for pre peening did make it a lot easier, although I just finished off with a hammer so I had more control

-
Great work

-
I carried it for half an hour before I realised I forgot something :ahhh :ahhh
Mini-driver for the corkscrew :D Now sorted
;)A quick count up of the features:
Full sized plain blade
Full sized serrated blade
Scissors
Wood saw
Corkscrew
Nail file
Inline awl
Phillips driver
Large flat blade driver
Small flat blade driver
Eyeglasses precision driver
Can opener.... untested
Cap lifter
Wire bender
Toothpick
Tweezers -

I think thats gotta be the most tools on an 84mm mod Ive ever seen. Excellent job!
-
I so envy you folks that have the skill to mod these SAKs. As SAKs are one of my favorite things, I like them even more for the fact they can be customized with so many different parts/implements as I like to call them. I've pondered over what would make my perfect SAK and it changes almost daily. Currently, I am quite content with the Swisschamp, but would actually like to add a pruner blade and electrician blade to it, along with possibly some other implements.
I think the SAK I really want is the XLT (correct me if I'm wrong), the one the adds the pruner, elec. blade, and cyber tool. ???
Anyhow, whenever I see a mod like this it gets the gears turning in my head and if I could afford the overhead, I might even get into modding myself! ::)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login