Hytest Axe
-
Looks like a good axe.

-
Cut the old handle off. It must have been only using about 60% of the handle due to the top portion being split. Removed a couple of the wedges. You can see the holes where they were and them sitting to the left of the vice

There is a proper metal wedge in there somewhere too, but it was too small and has ended up at a 45 degree angle.
Here's where I got to tonight. No wedge in yet as the ones I have are too small.
Close up of the stamp which you may be able to just see
Not sure if I should take the handle off again and file beck those protrusions in the eye or just bang the wedge in as is. What do you guys think?
The aren't very clear in the pic.
-
I also weighed the head when I had it off. Came in at 2.015kg or 4 lb 7 oz. So it would have been a 4 1/2 lb model.
Filed the nicks out of the cutting edge a bit too, and a slight sand of the handle. I have some raw linseed oil but have read that boiled linseed is better to use.
-
IMO leave it as is and go with a wooden wedge.
-
Hey Rob your bench looks very much like mine

I would take the handle out and just file back any sharp edges/burrs on the inside of the eye (top and bottom) (if you haven’t already)
Raw linseed is OK to use but might take a little while to dry

-
^ ^ ^. Agree with Tony.
-
@TazzieRob said:
I also weighed the head when I had it off. Came in at 2.015kg or 4 lb 7 oz. So it would have been a 4 1/2 lb model.Filed the nicks out of the cutting edge a bit too, and a slight sand of the handle. I have some raw linseed oil but have read that boiled linseed is better to use.
I knew the head looked big but a 4 1/2 pounder is real felling axe.
-
@Sparky415 said:
Hey Rob your bench looks very much like mine
I would take the handle out and just file back any sharp edges/burrs on the inside of the eye (top and bottom) (if you haven’t already)
Raw linseed is OK to use but might take a little while to dry

I'm not very good at keeping things spick and span. My whole shed looks a lot like the bench!
There aren't any sharp edges or burs but some that may cause reduced surface contact if they don't bite into the wood. I'll back the handle out again and give it a bit more clean up. Looks like the eye may be deformed a touch from heavy hitting on the poll. Will give the raw linseed a go.
I also weighed the head when I had it off. Came in at 2.015kg or 4 lb 7 oz. So it would have been a 4 1/2 lb model.
I knew the head looked big but a 4 1/2 pounder is real felling axe.
This one was designed or priced towards farmers and land owners for everyday duties. Came in 3.5, 4, 4.5 and 5 lb heads. I've never felled a tree, but this axe has split its fair share of wood.

-
@Sparky415 said:
Hey Rob your bench looks very much like mine
Notice the deodorant can alcohol stove in the bottom left of the bench pic?
-
Hey Rob your bench looks very much like mine

Notice the deodorant can alcohol stove in the bottom left of the bench pic?
I do now

And the beer keg below :D

-
-
The hardware store doesn't sell timber wedges, so I made my own. Using a flap sanding disk on the 4" angle grinder. Made my shed super dusty! Feeding the handle with linseed oil now, then will burnish with steel wool and finish the sharpen.
It was sharp enough that when it fell over and chopped through my vacuum cleaner cord it tripped the breaker to the shed!


-
@TazzieRob said:
It was sharp enough that when it fell over and chopped through my vacuum cleaner cord it tripped the breaker to the shed!
That’s brilliant Rob! :D

-
Thanks, mate

I made the wedge chunky enough to fill the extra space due to the handle being a tad small for the length of the eye. As I was pounding the wedge in I had to do it on the floor and dropped the axe. Thankfully it only got the one cord as there were a few laying there!
-
@TazzieRob said:
Thanks, mate
I made the wedge chunky enough to fill the extra space due to the handle being a tad small for the leg th of the eye. As I was pounding the wedge in I had to do it on the floor and dropped the axe. Thankfully it only got the one cord as there were a few laying there!
Lucky it didn't get your toes

-
Thanks, mate

I made the wedge chunky enough to fill the extra space due to the handle being a tad small for the leg th of the eye. As I was pounding the wedge in I had to do it on the floor and dropped the axe. Thankfully it only got the one cord as there were a few laying there!
Lucky it didn't get your toes

Kneeling down and it fell away from me. Even if I was standing the head would have ended up a handle length from my toes in any direction

-
Something very strange has just happened.
I logged into Photobucket with the intention of redoing the photos in this post by downloading them and adding them to Google Photos, and now I can see them straight from Photobucket. I'm assuming no-one else can see them?
-
So here are the updated pics
Before:
Eye after Nail "wedges" removed
Start of fitting process
Stamp
Before Tidying up the Eye
Eye Grinding
Casualty
Finished and oiled
-
Nice before and after pics
Looks like a nice axe
but be careful :ahhh :ahhh :ahhh :DJust noticed this thread is a couple years old
So how is it holding up 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






