My First Alox Mod.
-
@Tarrodemierda said:
well send me one and make it happen ;)Next one I see is yours buddy! :D
-
Congratulations Mikko, that's really some outstanding work.

Mike
-
thank u so much Mike!
-
Looking good man!! That's some nice work.

Be a stud and copy the magnifyer frame in brass for the empty spot!!!
-
well if id make a new frame,id stick a compass in it instead of mag.
so u like my work,really?
thats cool since u seem to be a guru in this area.
-
@Tarrodemierda said:
well if id make a new frame,id stick a compass in it instead of mag.so u like my work,really?
thats cool since u seem to be a guru in this area.
A brass compass the same shape as the original magnifyer would be awesome!
-
wouldn't all the metal of the tool mess up the compass readings?
-
@WhichDawg said:
wouldn't all the metal of the tool mess up the compass readings?Who cares, it would look great! :D
-
the only thing a cant pull out is how to make an Bail,that wont ruin easily the scales.hollow axle/pin would be the solution but i donno where to get one or how to make one really nicely.
[/quote]
You could rivet the bail on with a small thin brass or aluminum washer underneath to avoid hitting the scales. A hollow pin, I think would weaken the pin or or might need too thin a bail. Would also make riveting hard to do without riveting the hole too.Richard
-
yep youre thinkin like iam,about the fact that hollow axle that small in diameter would be weakening factor.....

-
Maybe I'm the only one who doesn't like hollow-rivet bails? On my Wenger SI the darn thing is constantly darting in front of the knife blade just as I'm about to close it. I've reshaped the blade several times to remove the resulting dent. >:(
-
I like bails :D
I've added bails to alox knives by drilling into the pin a few mm, it doesn't seem to have caused any problems. I think the alox knives are over engineered in the first place, they can handle quite a bit of abuse :)
Neil
-
J-sews is that the "Johnny Quest" spider in your avatar?
-
I've added bails to alox knives by drilling into the pin a few mm, it doesn't seem to have caused any problems. I think the alox knives are over engineered in the first place, they can handle quite a bit of abuse :)
Neil
oooo!
so thats one way to do it,i was worried about fully thru drilled axle u see.
-
I think you should forego the bail and place the ever-useful LANYARD HOLE opposite the phillips. =D
Two birds with one stone!
-
I like bails :D
I've added bails to alox knives by drilling into the pin a few mm, it doesn't seem to have caused any problems. I think the alox knives are over engineered in the first place, they can handle quite a bit of abuse :)
Neil
oooo!
so thats one way to do it,i was worried about fully thru drilled axle u see.
Long as you get it centred properly it all seems good. If you're a bit out it can go horribly wrong... don't ask me how I know ::) ;)
Neil
-
i have this watchmakers lathe,i think with that i could do the holes....

-
I just start off with a small hand drill and then use a pillar drill. Its not fancy but it works... most of the time :)
Neil
-
pillar drill is very useful in about any crafts,ive used it also as a light duty mill.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login