Show us your Spyderco
-
At what point do you oil your knives, guys?
Or, how often?I've had my Spyderco Ambitious for a few months now, hadn't used it for about a week or two and yesterday, when I took it out, it was almost impossible to open it with one hand/flip and the blade movement was kinda.. difficult due to friction. I oiled it and it's working perfectly, but I was just wondering how often you do this to yours?
-
Eh? Never had to oil my Tenacious or my Para2... they open smoother than when I got them.
The DF is a bit tighter so I should oil it again now, a month later... -
Yeah, it had never happened to me before. And as I don't tighten or loosen the screws usually, this can't have been the problem (overtightening or sth.). It's like the washers (I'm not familiar with the terms) were screaming while opening/closing the blade.
Or maybe it was some dirt, but I do keep them clean

-
Only oil them if there is an issue like yours or I happen to have the oil in hand and a knife close by.
Maybe if they we're exposed to.salt water I would but not often in the ocean.
-
@N_N_R said:
At what point do you oil your knives, guys?
Or, how often?I've had my Spyderco Ambitious for a few months now, hadn't used it for about a week or two and yesterday, when I took it out, it was almost impossible to open it with one hand/flip and the blade movement was kinda.. difficult due to friction. I oiled it and it's working perfectly, but I was just wondering how often you do this to yours?
Sounds like some corrosion might of started in or around the washers. Kind of strange for that to happen and in such short time unless you live in a corrosive environment.
As far as oil/grease in my own knives it is literally a knife by knife thing. Some knives like my Sebenza get grease every time I disassemble and clean it. SAK's and Spyderco's (or any folder really) normally only get oil if I notice it really needs it. I like to run certain knives "dry" as while the oil or grease helps initially it also attracts dirt and lint that will in turn make the blade deployment become stiff. I usually only do this on SAK's though. With the high polish you don't even need oil in most cases. On the same note other knives I would not normally run dry. Sorry for the rambling. Basically its just like I said in the beginning. Its different with every knife.
-
Thanks captain
I intended to disassemble it to clean it properly when I found out I didn't have a proper screwdriver. It's high time I bought one. -
@N_N_R said:
Thanks captain
I intended to disassemble it to clean it properly when I found out I didn't have a proper screwdriver. It's high time I bought one.Not sure if you are familiar with disassembling folders or not. If not you should look on youtube for the particular knife and there will most likely be a dis-assembly video or two.
Be extra careful with the screws, especially when reassembling and tightening them down making sure not to tighten to much and strip anything. It can and will happen easily if not careful.
If you have any questions and I can help I will. Good luck.

EDIT: As far as the drivers needed. It should just be Torx T-6 and T-8 if it is the same as the Tenacious. I suggest Wiha or Bondhus.
-
No, I'm not familiar with this :D It'll be just ... take one off, put it aside, take another part off, put it aside... and then assemble it by following these "steps" back :D
-
Only oil them if there is an issue like yours or I happen to have the oil in hand and a knife close by.
Maybe if they we're exposed to.salt water I would but not often in the ocean.
-
@captain spaulding said:
Thanks captain
I intended to disassemble it to clean it properly when I found out I didn't have a proper screwdriver. It's high time I bought one.Not sure if you are familiar with disassembling folders or not. If not you should look on youtube for the particular knife and there will most likely be a dis-assembly video or two.
Be extra careful with the screws, especially when reassembling and tightening them down making sure not to tighten to much and strip anything. It can and will happen easily if not careful.
If you have any questions and I can help I will. Good luck.

EDIT: As far as the drivers needed. It should just be Torx T-6 and T-8 if it is the same as the Tenacious. I suggest Wiha or Bondhus.
Cappy is right about the drivers and being careful you don't strip the screw heads.
Just wanted to add that in the future if you have or buy more Spydies that every screw Spyderco has ever used falls between T-6 for the small scale screws to T-15 for the pivot on a Military.
-
Thanks for the info! Well, since I don't have the appropriate screwdrivers at home, I'll have to go actually buyyyyy one(s) only for the pleasure of disassembling my Spydie. So maybe I won't do it soon. I do have one such screwdriver, but it's suitable for the tiny clip screws only.
My knife's safe for now. Unless I run to the store and buy screwdrivers
Who knows. lol -
Military in all black.
-
My last family photo , i have added two more Manbugs , a G10 and a ZDP.

-
@Toolslinger said:
Military in all black.Been researching my next Spyderco and I'm going with a Military. I love that it's a 4" blade.
-
@Toolslinger said:
Military in all black.Great looking Millie and I love the upside down picture.

-
Military in all black.
Been researching my next Spyderco and I'm going with a Military. I love that it's a 4" blade.
Excellent choice. The best Spydje imo.
There is a 110V Millie coming out at some point although it could be a while. Fyi.
-
Military in all black.
Great looking Millie and I love the upside down picture.

Looks rightside up to me...

-
Military in all black.
Great looking Millie and I love the upside down picture.

Looks rightside up to me...

Upside down on both my tablet and phone. Weird.
-
Nice Military TS. Its my favorite folder.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
