What did you use your Leatherman for today?
-
also used the rebar to disassemble a guitar amplifier that was in need of repare
-
@Zachbradley said:
also used the rebar to disassemble a guitar amplifier that was in need of repareNice! What kind of amp?
-
@Flint Hills said:
also used the rebar to disassemble a guitar amplifier that was in need of repare
Nice! What kind of amp?
I was wondering the same thing :)
-
@Flint Hills said:
also used the rebar to disassemble a guitar amplifier that was in need of repare
Nice! What kind of amp?
I was wondering the same thing :)
Pics

-
Used the rebar's saw to cut a long stick, for shaking off some walnuts of a few trees on the side of the road. Gathered a nice bag that way in a short time.
-
Its a Marshall MG 100fx 2x12

-
used my wave wire cutters to cut some wire. used the scissors to cut some electrical tape.
-
@jacktrades said:
Used the rebar's saw to cut a long stick, for shaking off some walnuts of a few trees on the side of the road. Gathered a nice bag that way in a short time.
-
@Rossko07 said:
Disconnected a burnt out vacuum motor to fit a new one.
That is exactly the kind of tasks that you can handle with a Wave and its siblings with their nice implementation of the flat bit-kit.
That is the reason I always have one with me in the car / bike-rides etc. The world is held together by torx and hex nowadays. -
Fixing my stove.
-
rebar helped me do a small modification to my car to install a mount for my phone
-
Used my Wave to cut some sticks for a camp fire

Dream. Wish. Leave nothing undone. Repeat.
-
I used the screwdriver on the PST II to tighten the chain on my chainsaw with the adjustment screw.
-
Not today but last week I put the Charge ALX to work. Drove 850 miles and on the first fuel stop rescued a damsel in distress with a loose battery cable. Got to destination and took a bed frame apart, took base off a TV and cut a lot of packing tape.
Got back and put the bed and TV back together, then put in two jacks one for phone and one for ethernet. -
Cut a gypsum board.

-
Fine tune and install robotic end of arm tooling, here cutting and trimming hoses and zip ties so that there are no loose ends that can be caught when the robot moves fast in 6 axes.

-
Fine tune and install robotic end of arm tooling, here cutting and trimming hoses and zip ties so that there are no loose ends that can be caught when the robot moves fast in 6 axes.

What does the robot chop with the axes?
Haha. Thats a misfortunate typo. I guess it moves in six axis, no axes. It was not a cyberdyne T-1000 killer robot but rather a humble ABB IRB 4600.
-
Fine tune and install robotic end of arm tooling, here cutting and trimming hoses and zip ties so that there are no loose ends that can be caught when the robot moves fast in 6 axes.

What does the robot chop with the axes?
Haha. Thats a misfortunate typo. I guess it moves in six axis, no axes. It was not a cyberdyne T-1000 killer robot but rather a humble ABB IRB 4600.
I can only think of 3 axis, care to explain?
-
Fine tune and install robotic end of arm tooling, here cutting and trimming hoses and zip ties so that there are no loose ends that can be caught when the robot moves fast in 6 axes.

What does the robot chop with the axes?
Haha. Thats a misfortunate typo. I guess it moves in six axis, no axes. It was not a cyberdyne T-1000 killer robot but rather a humble ABB IRB 4600.
I can only think of 3 axis, care to explain?
Sure,
There are of course only 3-planes to move in, and there are robots with only x-y-z (3 axis) movements, so called cartesian robots.
Six axis robots however have six axis that it can use to move it´s arm with extreme freedom within the 3-planes.
https://en.wikipedia.org/wiki/Six_degrees_of_freedom#/media/File:6DOF_en.jpg
Therefore, it is a challenge to distribute media like compressed air and current to the end of arm tool without compromising the movements or risk that a hose or cable is cut. There can be high risk if for example a vacuum hose brakes in a high acceleration movement and send a metal sheet like a frisbee.
That´s why all cable ties etc. have to be snug and the last preparation is what was in the picture before test run of the robot installation.
Here are the six axis explained:
https://www.youtube.com/watch?v=7coUcEHxnYAAnd here is something fun you can do with it:
https://www.youtube.com/watch?v=9PMCiMij0kQ
(I would never do that)Sorry for the off topic.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login