And so it begins.... (My adventures into Alox!)
-
-
@Syph007 said:
I think I will have to epoxy the lenses in, unless I can work out a rubber gasket or something similar.A gasket could work. There are probably Viton o-rings or something already in that size. For a different design, it would take some work, but maybe a small twist lock type of outer ring? Although, that does add to the complexity of the piece. Possibly a snap ring retainer?
-
@Syph007 said:
Parts are in! :D The scale wrench is rev. 3.I didnt bother to show the first 2 versions as they had some funny design flaws that didnt occur to me until I tried to use them. I'll explain in a later post, but this version works great. One side is to tighten, other to loosen. Normally a OPT wrench only needs one, but you can flip a normal OPT to use either side, cant do that with a scale mounted to a SAK. :D So yes ver 1 could only loosen bolts night tighten....



Yes! Potential Yeoman mod: mag glass and wrench on one layer and the Phillips as a back tool.
Great job, Bob!
...as for the scale wrench... Why not make it symmetrical with 'steps' on both sides?
-
Parts are in! :D The scale wrench is rev. 3.
I didnt bother to show the first 2 versions as they had some funny design flaws that didnt occur to me until I tried to use them. I'll explain in a later post, but this version works great. One side is to tighten, other to loosen. Normally a OPT wrench only needs one, but you can flip a normal OPT to use either side, cant do that with a scale mounted to a SAK. :D So yes ver 1 could only loosen bolts night tighten....



Yes! Potential Yeoman mod: mag glass and wrench on one layer and the Phillips as a back tool.
Great job, Bob!
...as for the scale wrench... Why not make it symmetrical with 'steps' on both sides?
That was ver 2. It didnt work, not enough surface contact and it slipped out. Here is what that one looked like.
Ver 3 I just did a regular bump pattern and it fits all the imperial and metric bolts Ive tried so far.

-
And this was ver 1.
At least 3rd times a charm! :D

-
Wow. Are the wrench scales 91 or 93?
Looks like 93mm to me

I too would like confirmation as this puts a custom SAK much closer to the top of my 'spend money on it' list.
I'd also like to know if the double opener would fit across from the wrench...
93 ya. I'll have something like this for 91s too though in 3-4 weeks. Its parts making month. :D I still got a few other coming in too.
-
Heres today's work. A 91mm compact that I left a brushed style finish on. This has Aluminum cross as well. It actually leaves a decent contrast on the bare Ti.








-
Questions about the new wrench piece.
- Will it fit on the same layer as the double opener (can and bottle)?
- Will the philips fit across from it?
Both assume the 93mm frame.
-
Now, for the version with inline wrench as a layer tool, one could make a scale that has just the bit cut-out, in place of the cross...
-
Wow! I can now say that SAK stands for Syph Army Knife.
-
@Toolslinger said:
Questions about the new wrench piece.- Will it fit on the same layer as the double opener (can and bottle)?
- Will the philips fit across from it?
Both assume the 93mm frame.
I have to get one prepped then I can test it. I tested the fit of the wrench area on teh scales and those work perfect. I have a set tumbling right now. :D
-
Questions about the new wrench piece.
- Will it fit on the same layer as the double opener (can and bottle)?
- Will the philips fit across from it?
Both assume the 93mm frame.
I have to get one prepped then I can test it. I tested the fit of the wrench area on teh scales and those work perfect. I have a set tumbling right now. :D

-
REALLY hope that mag glass and wrench go together on an 91.
-
In first as a test pilot for the new stuff.
It's a dirty job but someone has to do it.
-
Oh yes they are looking good. :D The 1/4 inch bit holder is perfect. Its slightly tapered and retains the bit perfectly. It does not fall out at all. :D







-
These are 93mm scales right?
If you were to carry some bits you would not even need the inline phillips. Would make for some interesting tool combos.
-
@HarleyXJGuy said:
These are 93mm scales right?If you were to carry some bits you would not even need the inline phillips. Would make for some interesting tool combos.
Yep 93. I will have scale options with this type of thing for all sizes though.
-
These are 93mm scales right?
If you were to carry some bits you would not even need the inline phillips. Would make for some interesting tool combos.
Yep 93. I will have scale options with this type of thing for all sizes though.
Have any issues with bolts slipping or being rounded off?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
