Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Fenix L2D problems

Scheduled Pinned Locked Moved Flashlight Forum
17 Posts 1 Posters 5.0k Views
  1. Home
  2. Non Tool Forum
  3. Flashlight Forum
  4. Fenix L2D problems
Fenix L2D problems
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • NutSAK Offline
    NutSAK
    Admin Team
    Posts: 8,463
    NutSAK Offline
    NutSAK
    Admin Team
    wrote on last edited by
    #1 Quote Reply

      There shouldn't be anything between the LED "pill" and the reflector.

      I've worked on a lot of Fenix lights. I hate to the the bearer of bad news, but it sounds like something on the circuit board has gone bad. Does strobe mode work, or just turbo?

      1 Reply Last reply
      • Abstraction Offline
        Abstraction
        Posts: 353
        Abstraction Offline
        Abstraction
        wrote on last edited by
        #2 Quote Reply

          Yeah the strobe works just fine but it's either turbo mode or strobe unfortunately, and the head just doesn't seem to twist as smoothly as it used to. Any idea how good the Feinx warrenty is in the UK? It should still be covered but i have none of the original packaging unfortunately. I bought it from Heinnie so i might send them an email.

          1 Reply Last reply
          • NutSAK Offline
            NutSAK
            Admin Team
            Posts: 8,463
            NutSAK Offline
            NutSAK
            Admin Team
            wrote on last edited by
            #3 Quote Reply

              There is only one thing that would cause the normal modes to not work on the L2D other than the circuit going bad. If the contact ring on the bottom side of the head is somehow shorted to the walls of the head, it would make this happen. That is how the switch works--when the head is screwed down tight against the body, that connects the contact ring with the body of the flashlight. Otherwise, they should be electrically isolated. Be sure there are no foreign objects inside the head where the body screws in.

              1 Reply Last reply
              • Abstraction Offline
                Abstraction
                Posts: 353
                Abstraction Offline
                Abstraction
                wrote on last edited by
                #4 Quote Reply

                  Thanks for the help, i can't see any foreign objects, it does feel slightly 'grainy' when i screw it on but nothing there that i can see. I emailed Heinnie and linda has already got back to me, within 15 minutes! She said i can send it back to them and they will either get it repaired or replaced :) Will just do that i guess, as there's nothing i can see wrong with it and if as you say the circuit is fried then there won't be much i can do! I just hope their returns policy is as fast as their reply's to emails!

                  1 Reply Last reply
                  • NutSAK Offline
                    NutSAK
                    Admin Team
                    Posts: 8,463
                    NutSAK Offline
                    NutSAK
                    Admin Team
                    wrote on last edited by
                    #5 Quote Reply

                      Sounds good!

                      1 Reply Last reply
                      • edap617 Offline
                        edap617
                        Posts: 3,958
                        edap617 Offline
                        edap617
                        wrote on last edited by
                        #6 Quote Reply

                          I could be wrong but here's my analysis of the problem.

                          The lower portion of the head (red arrow) got stucked to the body tube, hence it is permanently engaged in turbo mode. You were actualy turning the upper join (blue arrow) and the grainy material you mentioned is dried loctite. Turn counterclockwise the lower portion of the head (red arrow) to release the turbo mode.

                          Remove all grainy materials on the thread of the lower portion of the head (2nd pic, yellow arrow), apply loctite and tighten.

                          Next time when you want to change mode don't hold the upper portion of the head. Hold only the lower portion with knurling.

                          1 Reply Last reply
                          • NutSAK Offline
                            NutSAK
                            Admin Team
                            Posts: 8,463
                            NutSAK Offline
                            NutSAK
                            Admin Team
                            wrote on last edited by
                            #7 Quote Reply

                              hmmm... That is a very good analysis. I thought it was odd that his head separated anyway....

                              I'd say you're right Eddie.

                              1 Reply Last reply
                              • edap617 Offline
                                edap617
                                Posts: 3,958
                                edap617 Offline
                                edap617
                                wrote on last edited by
                                #8 Quote Reply

                                  Thank you Terry.

                                  1 Reply Last reply
                                  • Abstraction Offline
                                    Abstraction
                                    Posts: 353
                                    Abstraction Offline
                                    Abstraction
                                    wrote on last edited by
                                    #9 Quote Reply

                                      That's it! Nice thinking mate. I was wondering why it 'felt' different to twist, it's twisting in a different place! The only thing is, there's no way i can get the lower part to twist, i'm not a small guy and my grip has got me through over a decade of Judo, but this thing aint budging now matter how hard i try!

                                      1 Reply Last reply
                                      • edap617 Offline
                                        edap617
                                        Posts: 3,958
                                        edap617 Offline
                                        edap617
                                        wrote on last edited by
                                        #10 Quote Reply

                                          Try wrapping the part that got stucked with rubber band or flat tourniquet.

                                          1 Reply Last reply
                                          • Abstraction Offline
                                            Abstraction
                                            Posts: 353
                                            Abstraction Offline
                                            Abstraction
                                            wrote on last edited by
                                            #11 Quote Reply

                                              Done it :D cheers mate, i wrapped it in a rubber glove, then two tea towels and got a swisstool to the top part of it and a wave to the bottom, quick twist in either direction and it was loose with no damage to the body! Now just need to clean and glue the top bit, would you recomend a bit of WD40 on the threads to stop that happening again or would that not be wise so near the battery's? It's working perfectly again at any rate though so cheers for that, saved me a bit of a wait, i just have no idea how it managed to get stuck on 'that' tightly!! I was pretty pissed when i used it out camping but i'm sure i wouldnt have overtightened it like that.

                                              1 Reply Last reply
                                              • edap617 Offline
                                                edap617
                                                Posts: 3,958
                                                edap617 Offline
                                                edap617
                                                wrote on last edited by
                                                #12 Quote Reply

                                                  I think grease is better than oil. WD40 is too light.

                                                  I'm happy your L2d is now ok mate!

                                                  1 Reply Last reply
                                                  • Abstraction Offline
                                                    Abstraction
                                                    Posts: 353
                                                    Abstraction Offline
                                                    Abstraction
                                                    wrote on last edited by
                                                    #13 Quote Reply

                                                      So am i, great great light so it was frustrating for it to develop problems! Thanks a lot to both of you for your help :) I can't believe it was something so simple, the thing was on so tight i really didnt think that there was another joint in there! I just figured the reason it felt different to twist was something to do with the problem!

                                                      1 Reply Last reply
                                                      • NutSAK Offline
                                                        NutSAK
                                                        Admin Team
                                                        Posts: 8,463
                                                        NutSAK Offline
                                                        NutSAK
                                                        Admin Team
                                                        wrote on last edited by
                                                        #14 Quote Reply

                                                          Good job Eddie!

                                                          You should use some silicone grease on the threads and o-ring. You can usually find this at hardware stores in the plumbing section. A small drop of Loctite on the other threads dried overnight will keep the head from separating.

                                                          1 Reply Last reply
                                                          • Teofilo Offline
                                                            Teofilo
                                                            Posts: 2,332
                                                            Teofilo Offline
                                                            Teofilo
                                                            wrote on last edited by
                                                            #15 Quote Reply

                                                              :cheers: to your L2D, Abstraction!

                                                              1 Reply Last reply
                                                              • Abstraction Offline
                                                                Abstraction
                                                                Posts: 353
                                                                Abstraction Offline
                                                                Abstraction
                                                                wrote on last edited by
                                                                #16 Quote Reply

                                                                  Cheers mate, i was worried for a while there that i wouldnt be able to make maglite users feel inadequate anymore :D

                                                                  I'll pick up some silicone grease next time im in town, already cleaned out the threads and put some superglue on it , will leave it to dry for a while now :)

                                                                  1 Reply Last reply

                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                  With your input, this post could be even better 💗

                                                                  Register Login

                                                                  1. Home
                                                                  2. Non Tool Forum
                                                                  3. Flashlight Forum
                                                                  4. Fenix L2D problems
                                                                  Reply
                                                                  • Reply as topic
                                                                  Log in to reply
                                                                  COMMUNITY LINKS
                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                  Operational Funds

                                                                  Help us keep the Unworkable working!

                                                                  Make A Donation
                                                                  November Goal: $300.00
                                                                  Due Date: Nov 30
                                                                  Total Receipts: $0.00
                                                                  Below Goal: $300.00
                                                                  0% funded
                                                                  • Login

                                                                  • Don't have an account? Register

                                                                  • Login or register to search.
                                                                  • First post
                                                                    Last post
                                                                  0