Maintenance Multi-tool
-
As much as I'm a fan of the Vic Spirit,I'd go Wave on this one. You'll find the bit driver invaluable. Likewise,you say you don't need a saw,but I suspect you might be surprised! After all it's better to have it and not need it than need it and not have it

-
SuperTool 300, or a Rebar if you prefer a slightly smaller tool. Other than the knives not being one-hand open, they're about as simple and reliable as multitools could be. Replaceable wire cutters so when you do damage them cutting barbed wire you can swap them out easily instead of having to send it back for repair.
Or, a pair of pliers and a Leatherman C33T.
-
I'm going to agree with hiraethus on this one. ST300 would be my choice. It is also dead easy to clean as there is nothing fancy going on inside the handles. Everything is contained in one package and there are no fiddly bits to get lost or keep track of. It also has a nice form factor for riding in a pouch or pocket and isn't atrociously heavy considering it's size and capabilities.
-
The LM Surge will do you good on a farm like that. Also, I believe you will find the the file and saw will come in very handy on the farm.
That's us mobile.
Nate -
@Smaug said:
Leatherman Surge. I recommended this because it has great pliers, a good wire cutter, great flat head, great Phillips, one hand opening blades.I'm not crazy about the bit driver phillips, prefer a solid one.
@StephenAndMelissa Smith said:
I am moving to Honduras to work as a missionary for a non-profit organization that runs a leadership and business university for underprivileged women. I will be managing their campus including maintenance and upkeep for their buildings, farm, and coffee plantation, 200 acres in total.All the best for your err missionary position.
-
I'd go with the Supertool 300.
-
As much as I'd say go with a mt, a pair of regular pliers and a pair of heavy duty cutters paired with a Crater C33T or a Victorinox Trekker/GAK might be a good route to. As much as you say you don't want the saw, its best to have it and not need it as opposed to not having it and needing it.
I'd also throw in a pair of electrician scissors and something like a Klein 11 in 1 screwdriver into the mix for all the different types of screws out there:
-
I would have suggested the ST300, but I got thinking that a hammer may also be useful, as well as a variety of bits.
I would therefore also suggest the one hand opening Leatherman MUT
-
Id recommend getting either a Leatherman Wave/Surge/Rebar/Supertool 300, paired with a good small fixed blade (such as something from ISEE) or folder (if fixed blade is not an option). I recommend a separate knife, becasue even though the Wave/Surge have excellent blades for multitools, dedicated knives are significantly more comfortable and robust, with little loss in your comfort for carrying it.
Rebar/SuperTool 300 are no nonsense tools. The Rebar is the Super Tools little brother, and share very similar toolsets. Their Phillips drivers are excellent, working well on both #1 and #2 Phillips heads. 2 flathead (3 on ST300), awl, canopener/wirestripper, straight and serrated blades, file and saw. The Super tool has larger and longer everything, but is larger than Rebar, which many with small hands find uncomfortable.
Wave/Surge are considered the next step in Leathermans lineup. They swap out the full sized phillips and a flat head (surge has 2, Wave has 1) for a bit driver, which uses Leathermans proprietary bits. They also feature scissors (big outside opening ones on Surge) a diamond coated file, can opener saw, and One hand opening straight and serrated blades. Surge also has a blade exchanger that works with standard t shank jigsaw blades (also holds file or woodsaw), an awl, and the same new style plier jaws that Rebar and ST300 has. Wave features has the old style plier head, which isnt as good for cutting wire, has a larger bolt gripping section. The Surge is larger than Wave, and has larger implements. Wave is same length as Rebar, but thicker. Surge is same length as ST300, also thicker. I am unsure of relationship of thickness between wave and ST300, but I believe they are similar.
If you decide to get the Leatherman bit kit, or any other bit kit, invest in the Bit Kit Extender for Wave/Surge, or Removable Bit Driver for Rebar/ST300. These accessories accept standard hex bits as well as Leathermans proprietary bits (Leatherman bits fit in all standard 1/4" hex bit drivers, albeit loosley). The fill Leatherman kit is very comprehensive, and very compact.
Also, seriously consider getting a decent flashlight, and a Skinth sheath to carry everything in. -
Keep in mind your hand size. Members have raised issues with handle splay on the larger MTs.
I believe the Surge is your best bet if splay is not an issue. I'd pick up a spare set of replaceable wire cutters and blades. The Surge while it has "fiddly" parts like the bits and blade exchanger IMO it offers exactly what you want. It also comes with extras for those times you might need them. If you plan on carrying your tool in a sheath then there is no reason why those "fiddly" parts would pose a problem.
You'd be hard pressed to find a MT without the can opener. The metal file and saw will come in handy, that I'm sure of.
Now if your aren't sold on the Surge then the ST300 is a terrific option. No OHO tools but a solid performer.
All the best to you.
-
Leatherman Wave: has a compatible bit kit, one hand opening knife, and everything else you require in a decent sized package with pocket clip.
Gerber MP600: I would suggest avoiding the type with the indexable cutters. One hand opening pliers, and compatible bit set, but this one takes full 3D 1/4" bits which would be easier and cheaper if you need to replace due to loss/wear/damage. Has everything else you are looking for, but no pocket clip. Sheath carry. A blunt nosed version with blade exchanger may prove to be a good option for you
Victorinox Spirit: has every tool you could possibly wish for, including chisel and pry tool, and is very well made. Knife is outside accessible, but two hand opening. Additional bit set is available with a bit wrench or ratchet. Bit wrench is stronger than any of the other options mentioned in this post, and takes the full 3D easily replaced 1/4" bits.
NOTE: as the Victorinox bit wrench is available seperately, there's nothing to stop you getting one to accompany a Wave or MP600. It should be noted also that this bit wrench beats everything else for hard to access screws in awkward places. Irrespective of what multitool you choose, DO consider one of these

If you expect to be cutting a lot of barbed wire or fencing wire, consider taking a separate pair of drop forged wire cutters, as these would be superior to the cast plier heads typically offered on multitools.
Surge or ST300 may be good alternative choices, assuming they are going to be used by someone with large hands. A Victorinox Swisstool (the Spirit's bigger brother) would be another alternative in this size. I have average hands and can get better gripping/cutting force on a smaller chassis tool. The MP600 is actually a large chassis tools, but is more friendly to a wider range of hand sizes.
Rebar is a pocketable/diminutive version of the ST300, but they scaled down the durability as well, and the knive blades in particular are not very robust. I would not recommend this for you.
Please do let us know what you choose, and pop in when you can to give some user feedback both on it's performance but also it's suitability for the tasks you face

-
@50ft-trad said:
Leatherman Wave: has a compatible bit kit, one hand opening knife, and everything else you require in a decent sized package with pocket clip.Disclaimer: Pocket clip on Wave is an add-on, and not normally included with the tool.
EDIT: however, it's a GREAT add-on, and well worth the extra few bucks, IMO.
-
My first choice would be a surge,then st300,something a bit smaller victorinox spirit or lm wave,good luck

-
Swisstool so you don't have to worry about humidity rusting your tool.
-
My brother works as a Maintenance in large apartment complex, he loves the ST300
-
MP600 will hold up to the rigors of a farm

-
Thanks for the great feedback.
The bulk of the responses were favoring Leatherman. I was surprised to see only a few Gerber & Victorinox and no SOG mentioned.
I like the advice for the saw, thinking particularly for PVC pipe.
What do most people use their files for?
It looks like you get either file or saw on the Surge but not both at the same time. Is that correct? Can you swap the scissors out with the file or anything?
I have reasonably large hands so I'm not too concerned with tool size. At the moment I'm leaning toward the Surge or ST300 based on their heavy duty build. I like the one hand open blades on the Surge. The bit kit seemed "fiddly" to me as my first impression, but I have never used it. It sounds like it is pretty popular so they may have implemented it well. I like being able to use standard 1/4" drivers since they are easily replaceable. It appears this is the case with the Gerber MP600, but not the Leatherman. Is that correct?
I like the rotation option for the Gerber MP600 wirecutter insert.
Also appreciate the other suggestions for secondary tools (pin socket, bit wrench, etc)
-
You can change out the saw for the file and vise versa on the Surge. Also, if you get the bit extension, you can use 1/4 bits. The flat bits will surprise you. I use mine on the farm all the time and at work. The file is good for smoothing out metal and plastic and in a pinch, sharpen you blade. These are not cheap files. They work rather well
Something else you can check out is the SOG Powerlock. You can change out the tools for different ones and it will NOT void the warranty. Also, you can use sockets on it and 1/4" bits with it. If you are going to cut a lot of wire, SOG pliers are hands down the best, period.That's us mobile.
Nate
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


