Maintenance Multi-tool
-
The Surges blade exchanger will accept Tshank blades. You now have a tool that can cut a variety of materials. The metal file for me has been used to knock down burrs. I've also filed down "just enough" material when cutting was over kill. There is a diamond side so you can sharpen your blade if needed. Great thing about the file is it can be removed so you can have the saw there if thats whats used more.
The blade exchanger is either saw or file not both at same time, you are correct.
The scissors are really nice on the Surge. You can mod the tool and remove them however I find when you need scissors, thats what works best.
Pick up a bit extender from LM, this will increase reach as the name suggest and allow you to use 1/4in bits as well. With this add on part you can also use sockets as well.
As far as fiddly goes, using LM flat bit vs 1/4in bits its a draw IMO. The flat LM bits being 2D vs 3D have not been an issue for my usage.
Not bad for all fitting in the LM nylon sheath ( minus sockets ).


-
Leatherman is usually the popular choice and will usually get the most recommendations. In your situation they do offer more potential candidates than other makers in my opinion. Generally they would not be my first choice (long story) but in this instance a Wave, Surge or ST300 should quite rightly be high on the list of suggestions
A few other thoughts
Leatherman Bit Kit: Lose/damage one bit, and you have to buy a full set to get a replacement. The bit extender works with the same driver (Wave and Surge), and converts them to full bits - however the reduced sized driver is still taking all the load. A compatible adaptor for the Phillips on the ST300 or MP600 would be stronger .... or the Victorinox Bit Wrench
(seriously, look into this)MP600 rotatable bits.... avoid!! If you're cutting soft stuff regularly, you will see reduced wear. If you're cutting harder wire however, they are likely to shatter/fracture as they are made of carbide (hard but brittle).
SOG has the compound leverage, but the wire cutters are easily deformed by harder materials, and their internal tools are lacking when compared against Leatherman, Victorinox and Gerber IMHO
Files? Deburring, cleaning corroded terminals squaring up a roughly cut pipe joint.... useful to have, even if not used regularly.
If I was going off to do the kind of work you're looking at, there's probably one other multitool I'd seriously consider taking. You'll probably know them as crate openers, but over here they tend to get called roofing tools... combined axe, hammer and prybar, and for the size of a small camp axe. Consider it the brute force solution to all problems that your pliers tool can't resolve :D mine has been surprisingly useful when it's not sensible to take a full compliment of dedicated tools.
-
Oh, just one more thing (said the wonky eyed detective), whichever tool you get, look it over thoroughly and take it for a test drive before you go off on your quest. Quality slip ups can and do happen, and you want to be sure you find and resolve any issues and address them before you head off

-
@50ft-trad said:
.... or the Victorinox Bit Wrench
(seriously, look into this)Is this the right one?
http://www.victorinox.com/us/product/Swiss-Army-Knives/Category/Accessories/Nylon-Pouch-with-Bits-Wrench/33340 -
@StephenAndMelissa Smith said:
@50ft-trad said:
.... or the Victorinox Bit Wrench
(seriously, look into this)Is this the right one?
http://www.victorinox.com/us/product/Swiss-Army-Knives/Category/Accessories/Nylon-Pouch-with-Bits-Wrench/33340That's the baby
Standard driver bits fit in both ends, and the case comes with a few standard bits and a few empty slots to add your own. Excellent little tool! -
@50ft-trad said:
If you expect to be cutting a lot of barbed wire or fencing wire, consider taking a separate pair of drop forged wire cutters, as these would be superior to the cast plier heads typically offered on multitools.+1 ^
MultiTool wire cutters may be damaged trying to cut wire that is too hard/thick
-
The ST300 and Surge were good suggestions, keep it simple with the ST300
Put a Spyderco Delica or Endura in your pocket and you are good to goI gather other dedicated tools will be available to you
-
Considering scissors are not on you list I think the Super Tool 300 would be a better fit. Nice long drivers. A real phillips. You can also get the bit driver to use normal 1/4" hex bits.
Bit Kit 3 | Leatherman
Leatherman Bit Kit 3 features Phillips #0 and #3, Torx T10–T15, and flatheads 0.2–0.075 in. Includes Hex 4–6mm for everyday repairs and adjustments.
Leatherman (www.leatherman.com)
The ST300 is a simple, effective, tradesman tool. You won't be disappointed with it. Hope this helps.
-
@Marcellus said:
I gather other dedicated tools will be available to youYes, I plan to have dedicated tools for major tasks. Looking for the multi-tool as a go to through out the day when I might not have my tool bag handy.
-
As an ex maintenance engineer I feel reasonably qualified to answer this. :D However I will say that this is still just a matter of opinion and there is always room for personal preferences. For me the Spirit X is the go-to choice. The comfy grip on the pliers and the long screwdrivers are what seals the deal IMO. Sorry to say that I'm not a huge fan of the flat LM bits, too fiddly and too short too often.
If you are going to be doing any serious amount of heavy steel wire cutting then I really think you'll want some dedicated cutters though. The replaceable ones on the ST300 and Rebar are definitely better than the ones on the Spirit, but they still pale in comparison to the real deal.
All the best with the project.

-
You think maybe a pair of 8" knipex bolt cutters? Or is that overkill?
-
@Demel said:
Considering scissors are not on you list I think the Super Tool 300 would be a better fit. Nice long drivers. A real phillips. You can also get the bit driver to use normal 1/4" hex bits.
Bit Kit 3 | Leatherman
Leatherman Bit Kit 3 features Phillips #0 and #3, Torx T10–T15, and flatheads 0.2–0.075 in. Includes Hex 4–6mm for everyday repairs and adjustments.
Leatherman (www.leatherman.com)
The ST300 is a simple, effective, tradesman tool. You won't be disappointed with it. Hope this helps.
Is the removable bit driver compatible with the ST300? How does it attach? on the flat head?
Good point on the scissors.
At this point I am leaning toward the ST300 or Surge.
ST300 Pros:
longer philips bit
has both saw and file at the same time (no scissors)Surge Pros:
has on hand open blades
interchangeable t saw blades
Interchangeable bits (Unsure, Seems to be mixed opinions on)How does the locking mechanism on the ST300 compare to the liner locks on the Surge?
Also note, probably correct on the wire cutters, will plan to used dedicated cutters most of the time and the MT cutters when in a pinch.
-
While i've never had a Surge, it's liner locks are similar/same as the Wave, and the locks on ALL of the leathermans you're looking at are all really solid.
Sometimes blades will have a very tiny amount of play when locked, but it doesn't affect their use, and more often, they're rock solid lockups.
-
Just go with BLAST-OFF


-
@StephenAndMelissa Smith said:
Considering scissors are not on you list I think the Super Tool 300 would be a better fit. Nice long drivers. A real phillips. You can also get the bit driver to use normal 1/4" hex bits.
Bit Kit 3 | Leatherman
Leatherman Bit Kit 3 features Phillips #0 and #3, Torx T10–T15, and flatheads 0.2–0.075 in. Includes Hex 4–6mm for everyday repairs and adjustments.
Leatherman (www.leatherman.com)
The ST300 is a simple, effective, tradesman tool. You won't be disappointed with it. Hope this helps.
Is the removable bit driver compatible with the ST300? How does it attach? on the flat head?
Yes it goes over the phillips driver. Its really helpful without having to replace leatherman bits and using normal bits instead.
-
@Aloha007 said:
The scissors are really nice on the Surge. You can mod the tool and remove them however I find when you need scissors, thats what works best.+1, I would not remove the scissors on a Surge, they are one of it's best features. You may find them more useful than you think.
The Surge is not only big, it is heavy as well - some don't like this so it would pay to handle one first.
One thing I have used the Surge for is shortening bolts using a metal jigsaw blade then using the file to clean up the edges. I find the OHO blades very handy as well. -
Don't know if you've seen the thread below yet :pok:. I know the rust "issue" comes up when talking LM but I have not yet had any issues. The other knock are the bits yet what's the difference then in using 1/4in bits besides shape? I love that I can change out blades/saws to suit whatever material I'm cutting. While not the best way or easiest longer Tshank blades can be used tho I wouldn't go to long.
/post/1154134
The tool tested is the older version without the replaceable 154cm wire cutters. This one also has the small bit driver.
I know it's a not in english but the video is worth a look IMO.- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
Get real tools! PH2/Flat screwdriver and a pair of pliers (one for gripping one for cutting)
Get a Farmer! excellent pocket knife, you will love it (better get 2 or 3 of these)
Get a fixed blade and an axe!
Get something to sharpen your knifes!
If you have money left! Get a MT that can work alone and does not need bits and blades and whatever. My recommendation would be a Vic Spirit (IMHO best tool selection) or a Rebar (much cheaper).About the Vic bit-kit:
The Vic bit-kit is excellent, but pricey. You probably can get a much cheaper bit kit at your local hardware store, although it might not be as compact.About the Surge:
Before you get a LM Surge, try one. I found it way to big and had tons of issues with it. For example I had trouble gripping stuff due to the large size combined with quite pointy pliers (needs large hands / strength)
**Blade Holder / Bit Holder: **Are interesting choices as they add versatility. However small parts easily get lost and might be hard to replace (especially LM bits).
Considering that you are not interested in File/Saw etc I think the Surge is a poor choice (I mean it will be good to have those but you probably won't need a blade exchanger). -
StephenandMelissaSmith,
If you have an REI store near you, you might be able to try out the various tools we've recommended before purchase. This would let you know if the tool is comfortable in-hand, and at least give you minimal idea if its functions suit you.
Just a thought.
-
@StephenAndMelissa Smith said:
I gather other dedicated tools will be available to you
Yes, I plan to have dedicated tools for major tasks. Looking for the multi-tool as a go to through out the day when I might not have my tool bag handy.
If he was marching on to a planned project, my brother would carry his tool bag with him.
But most the time he would inspect the issue first, if it is a quick fix, the ST300 in his pocket would just fix it on spot.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login