Show off your Sak mod's!
-
Fantastic job!!!!!

-
Very nice Steve, looks like a classy pocket knife.

-
Lovely job
Great tool selection -
TatSteve I have a OC Pioneer that has some issues closing, like it lost some of its snap.
Is that something that can be fixed?
-
@HarleyXJGuy said:
TatSteve I have a OC Pioneer that has some issues closing, like it lost some of its snap.Is that something that can be fixed?
This just came up here
</topic/62704
-
@HarleyXJGuy said:
TatSteve I have a OC Pioneer that has some issues closing, like it lost some of its snap.Is that something that can be fixed?
Yes it can be. Cleaning it throughly is the first step. After that who knows. It is possible a pin is bent or something is broke. Either of those I can fix :)
-
TatSteve I have a OC Pioneer that has some issues closing, like it lost some of its snap.
Is that something that can be fixed?
This just came up here
How to bring snap back to older SAKS? (without dismantling)
I have an 1970s Spartan that has very little if any snap, what would be suggestions for bringing the snap back short of taking it all apart? I would rather n...
Multitool.Org Forum (multitool.ninja)
Good thread but I never leave wd40 in a sak. It displaces water and dirt which is good. But after that always clean it off. Then use a good grade mineral oil. I've noticed since I switched to using that instead of some other lubrication it works great.
-
Good info thanks.
Steve are you sure you don't want to pass on that OC Farmer so I can buy it?
-
-
-
Awesome!!! Love the file!
-
@hiraethus said:
DIY Modeler:

Nice selection of tools

-
Apologies in advance because I'm sure this has been covered, but would anyone care to share either a source or idea for the proper size pin stock for the rivets? I'd like remove the corkscrew and install a Philips driver in a Waiter as my first mod... :)
-
@Sheradin said:
Apologies in advance because I'm sure this has been covered, but would anyone care to share either a source or idea for the proper size pin stock for the rivets? I'd like remove the corkscrew and install a Philips driver in a Waiter as my first mod... :)2.5mm for the tools and 2.2mm for the springs and backtools.
-
I'm sure you have probably encountered this, but a Waiter with a phillips instead of a corkscrew is called an Apprentice (some boxes had them accidentally labelled "Apprenice" without a t).
As for a source for the rod, especially the 2.2mm, some local hobby shops might have something available but if you look on here, someone recently posted a source in the UK.
Good luck. The Apprentice is one of my favorites.
One other thing. I thought 84mm was 2.2mm for all pins and 91mm was 2.5mm for the tools and 2.2mm for the back tools and springs. All of the pins on 93mm are 3.0mm if I remember correctly. Of course I'm new so I could be wrong.
-
@s1xty7 said:
One other thing. I thought 84mm was 2.2mm for all pins and 91mm was 2.5mm for the tools and 2.2mm for the back tools and springs. All of the pins on 93mm are 3.0mm if I remember correctly. Of course I'm new so I could be wrong.93mm knives have a 2.5mm centre pin, not 3mm. Otherwise, all good.

-
Thank you all for the info, I have a local hobby shop or two that needs visiting...
I had seen the Apprentice but unfortunately also saw the prices some bring! Figured I'd probably spend twice as much, bugger a couple perfectly serviceable knives, curse a bit, and try to make my own... :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



, it needs catchy a name.