Off-Brand Challenge - ETHEREALICER - Böker City Tool / SWIZA D04
-
I dunno about you guys but the cut-out holes in the tools just scream "cost cutting" to me.
-
It costs more to machine the holes out than to just leave them in.
-
-
Definitely cheaper to have the through hole. Its harder to make a good nick. The only benfit of a through hole is that it can be acccesed from both sides.
-
I think the way Vic does it, the blade is stamped out, and then followed up with another press op which simultaneously produces the primary blade angle and the nail nick. If that's the case, it will add less than two seconds to the processing time. Machining, or even laser cutting the hole, would take notably longer. Even if I'm wrong, and it's a separate operation, punching a nail nick is a very quick process
-
You lot will not be popular in a spyderco forum

-
Big difference, Spyderco has the hole close to the pivot, where food is less likely to get stuck. The Spidy-hole is also excellent for OHO.
The holes on the Swiza also help with opening, but on the blade I find it a nuisance.
With the Swiza its a matter of what is more important to you:- Easy opening thanks to the holes
- Difficult cleaning because dirt gets stuck in the hole.
Another problem with the hole is, that it needs to stick out of the frame to be accessible resulting in an uncomfortable grip.
Thanks Syph/Al for clearing that up :P
-
@Etherealicer said:
Thanks Syph/Al for clearing that up :P:D :D :D
Glad we could be of assistance :P
-
@50ft-trad said:
Thanks Syph/Al for clearing that up :P
:D :D :D
Glad we could be of assistance :P
You know how confusing it would be if you two had said the exact opposite? ::)

-
As if we'd do such a thing

-
@50ft-trad said:
As if we'd do such a thing
I'm not saying you would do such a thing, I'm only saying it would be rather confusing if you did

-
Well, that's that cleared up too then

We're on a roll :D
-
I like the pumpkin

The SWIZA not at all.
-
@50ft-trad said:
I think the way Vic does it, the blade is stamped out, and then followed up with another press op which simultaneously produces the primary blade angle and the nail nick. If that's the case, it will add less than two seconds to the processing time. Machining, or even laser cutting the hole, would take notably longer. Even if I'm wrong, and it's a separate operation, punching a nail nick is a very quick processMy thought as well. A few blades later and you have paid for tooling (sure it will wear and stuff but still). Not to mention the recess and the engraving on the Swiza.
-
3 weeks ago I receive my first swiza knives :
The D01

The D02

The D03

And the D04

My first impressions:
-
they are "fresh" because of their color, a red-light near red-raspberry, because of the purity of their line, because of their fluid design, etc. FYI, design was provided by the company 'Estragon' in Zurich: http://www.estragon.ch/home/swiza-swiss-knife/
-
they have a good grip with good scales.
-
they are simply beautiful and they are "New Swiss way of life". These first 4 models are basic knives, like at the beginning of the Swiss army knife early 1900s. I suppose the range will grow with time...
It's difficult to compare a Swiza knife with other Swiss Army knives : new brand, new style, new concepts.
My opinion is the line of a Swiza knife is very similar to the french knife "Le Thiers" (the last knife).

Since 3 weeks I use a D03 like an EDC to test it in several situations...
First, It's a slim knife, I often forget I have a knife in my pocket. No keyring and no toothpick, but it's not a problem for me : I never used any keyring on a knife and I'm sure toothpicks are not very hygienics...
Swiza scales are soft, like Wenger soft-touch scales and it's very confortable, and Swiza scales cover external liners, like wenger scales...
All liners are stainless steel, not aluminium... So it's a strong quality !<u>The main blade :</u> 75 mm, just largest than a main blade of a soldier knife. This blade holds its cutting edge for a long time (longer than a lot of other Swiss Army Knives). Note all Swiza main blades are numbered for a best tracking in the time. All main blades are also "auto lock". The hole in the blade does not clog with cheese or mushy food. At worst, a simple cleaning with warm water would suffice to unblock. Everyone washes his knife before and after eating, isn't it?

<u>The awl :</u> It is formidable! It cuts better than the awl of an alox, it is shorter, wider and thinner in thickness. Attention, it is intended for materials such as leather or soft woods, not for hardwoods (risk of breakage). You can also use it like a small clip point blade to scrape with the tip, it is sharp as a doctor-blade. Caution, you must use it by turning to the left, unlike the other awls

<u>**The can opener / small screwdriver : **</u> With this can opener, mo risk to make damages to the scales! It is long, wide and very sharp!

<u>Cap-opener/screwdriver:</u> the small hook provided to position itself as one of the "slots" of a capsule is more pronounced/curled, so it seems more efficient, but I have not yet tested. But what a pity : the screwdriver is not "safety lock"...

The corkscrew: It can only be better than all corkscrew on Swiss Army Knives... More long, 5 coils, slightly tapered... Tested by sommeliers...

I have a good experience of Swiss Army knives, I have more than 600 knives of all ages, I am a collector... I can only welcome the birth of a new Swiss Cutler who brings on the market a new concept of Swiss Army knives.
-
-
Nice write up

Thank you for your views on them

-
Nice write up.

And your english is just fine :)
-
And now, for collectors, the first limited an numbered series for 2015 of SWIZA knives !

-
@jcfiguet said:
It is formidable! It cuts better than the awl of an alox, it is shorter, wider and thinner in thickness. Attention, it is intended for materials such as leather or soft woods, not for hardwoods (risk of breakage). You can also use it like a small clip point blade to scrape with the tip, it is sharp as a doctor-blade. Caution, you must use it by turning to the left, unlike the other awlsYup, used mine on on something hard and now the tip is blunt

Similar to the small flat and the Phillips, the tools showed lots of wear after the first use.@jcfiguet said:
The hole in the blade does not clog with cheese or mushy food. At worst, a simple cleaning with warm water would suffice to unblock. Everyone washes his knife before and after eating, isn't it?Well I use my SAK on food when I'm on the move and usually just wipe the blade. After cutting a pumpkin I found gunk in the hole even after putting the knife in the dish-washer.
@jcfiguet said:
<u>Cap-opener/screwdriver:</u> the small hook provided to position itself as one of the "slots" of a capsule is more pronounced/curled, so it seems more efficient, but I have not yet tested. But what a pity : the screwdriver is not "safety lock"...Will be curious to see how you get along with that, both dks and I found
"It worked, but it is not as good as the established Swiss gang"
to quote dks.How do you find grip comfort when using the blade on the 2-layers model? I
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login