And so it begins.... (My adventures into Alox!)
-
Say that you got a little overzealous peening your first mod and one of your pins is applying too much pressure on the joint. Any trick to fixing this? Or do I need to drill it out and start over?
-
The way I've heard it is you start over, but if anyone knows how to fix it short of that, you're in the right place.
-
Arrived today from the Great Northern Territories. :) Simply beautiful. Thanks, Syph!



-
@MachoGrande said:
Say that you got a little overzealous peening your first mod and one of your pins is applying too much pressure on the joint. Any trick to fixing this? Or do I need to drill it out and start over?Slide a thin piece of metal in between the layers and pry slightly. Also use a punch and tap lightly while the other side is not against a surface. Hard to explain that one.
-
@MachoGrande said:
Say that you got a little overzealous peening your first mod and one of your pins is applying too much pressure on the joint. Any trick to fixing this? Or do I need to drill it out and start over?Its easiest to start over especially if its really tight.
You can use shims in the assembly, then peen tight and pull the shims, I like that method.
-
Thanks for the advice, guys. Its not too bad. When closing the tool, the joint is just tight enough that the tool doesn't snap into the closed position as effortlessly as it should. I have to give a little assistance near the end.
-
Syph, the more I think about the cap lifter paired with the inline phillips on the 93mm, the more it makes natural sense. Way more useful than the can opener in my world. I guess I need to get some shim material, screws, pivots, and a couple of carbide 1/8" drill bits. I'm too nervous to hammer alox! Nothing crazy. A Pioneer with a can opener/phillips swap.
If its simple, why do I feel so apprehensive?
-
The phillips is thicker than the can opener, so you'll need a different spring - the blade spring works with a spacer/washer next to the cap lifter. Peening alox is fine if it's silver, a bit more nerve wracking on coloured scales.
-
Yea, I heard about the blade spring. I thought there was some slight modification on the cap lifter end required too. And its a .002 washer, right? Maybe get some phosphor bronze shim material to make a few washers with. I would want to do this on a several colors of Pioneer so maybe I should practice up on my peening first!
-
I'm trying to remember what I used in the past. 0.4mm brass sheet, I think.
-
@Syph007 said:
opener and phillips takes 0.105" of width on a single backspring. There is a 0.020" washer with the cap lifter to fill out the width.Ah, found the relevant information: .02". The only problem is the phosphor bronze I've seen is sold in MUCH larger quantities. I guess I'd have enough to make a few thousand washers! :D
Edit: Apparently USA Knife Maker has phosphor bronze washers in various thicknesses. While they don't have any in .02", they have pairs in .01" along with other thicknesses. Cheaper than ordering a whole sheet and making my own. Now all the parts are on their way. Ack!! My work simply won't be able to compare to any of the amazing stuff I see on here.
-
http://gearjunkie.com/best-multi-tools-knives-review
I reccognize that first tool! :D
-
@Syph007 said:
http://gearjunkie.com/best-multi-tools-knives-reviewI reccognize that first tool! :D
Best in the world eh? Can we believe him though? :P We all know the Wave doesn't have a 154CM blade... ;)
-
@Syph007 said:
http://gearjunkie.com/best-multi-tools-knives-reviewI reccognize that first tool! :D
Congrats! Now I have to order my next one fast, before you get even more overrun by orders due to that article.
-
As an outside observer I think you've earned the title! Unless Timbukto has an equivalent to MTO and there is some dude on there dishing out hundreds of sweet mods that we don't even know about. Maybe he's even made a custom backspring to put 91mm scissors on a 84mm :P
Very cool mate!

-
@Syph007 said:
http://gearjunkie.com/best-multi-tools-knives-reviewI reccognize that first tool! :D
Where?
I don't think I've ever seen that one :P -
This GearJunkie dude also thinks that Vic scissors suck? Really?
-
Wow, that is a cool article! From all of the amazing things I've seen you produce, I think it's pretty accurate. Your volume of work and quality are so prevalent that you're used as a reference point for how to do things as well as quality. There are quite a number of talented modders out there, but if wondering if something can be done or has been done, the answer is always the same: Syph did it.
Gee, now I feel like I'm hobnobbing with famous people!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login